Advertisement
Quick Links
Assembly Instructions
M105HV
Your Maco 105HV maxibeam is an innovation in base station beam design, which enables the
vertical and horizontal to be assembled for either 10 or 11 meters.
For example, using the charts supplied, you can assemble the horizontal for 11 meters and the
vertical for 10 meters, or reverse this, or assemble both the same. The horizontal and vertical
do not affect each other, so feel free to set your antenna up whichever way you wish.
THE ONLY DIFFERENCE BETWEEN THE HV BEAMS AND THE INSTRUCTIONS INCLUDED IS THAT THE
HV BEAM HAS BOTH SETS OF ELEMENTS ON THE SAME BOOM.
P LEASE ADD THE FOLLOWING INSTRUCTIONS TO THOSE SUPPLIED:
U
Mount the first reflector with the u-bolt facing the rear. Mount its mate with the u-
bolt facing the front of the beam. This is so the vertical and horizontal elements will
be close together.
Do the same with all the elements and measure the spacing only once per set of
elements.
Maco Antennas - a Division of Charles Electronics, LLC
302 S. East St.
Mt. Carroll, IL 61053
815-244-3500
www.macoantennas.net
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Maco Antennas M105HV
Summary of Contents for Maco Antennas M105HV
- Page 1 This is so the vertical and horizontal elements will be close together. Do the same with all the elements and measure the spacing only once per set of elements. Maco Antennas - a Division of Charles Electronics, LLC 302 S. East St. Mt. Carroll, IL 61053 815-244-3500...
-
Page 2: Packing List
WWW.ANTENNAPARTSOUTLET.COM Please note: In an effort to keep the price on Maco Antennas down, we have decided not to clean up all the burrs and rough edges on the parts. We recommend that you deburr and clean up each part with files, sandpaper, etc. -
Page 3: General Instructions
BLACK PLASTIC CAP\ ED PLASTIC R E F L E C T 0 DRIVEN ELEME 2” O.D. MAST ( C U S T O M E R F U R N I S H E D ) T H I R D D I R E C T O R D R I V E N ELEMENT‘- F I R S T D I R E C T 0 RED PLASTIC CAP (PLSR) -
Page 4: Boom Assembly
CENTER B O O M S E C T I O N (Tg2.P) VERTICAL GUY SUPPORT T O - M A S T C E N T E R B O O M S E C T I O N (T52P) , - - B O O M COUPLER SECTION... - Page 5 Please at the read the Assembly and Troubleshooting Tips end of this instruction booklet before assembling elements. FIGURE 3 ELEMENT ASSEMBLY AND MOUNTING Select a frequency in the center of where you work from the chart on page 7 and follow across for element dimensions “A”...
- Page 6 BOOM-TO-MAST PLATE (PO1 P) WITH BOOM ATTACHED 2” U-BOLTS (UOl) SADDLES (Sol) (CUSTOMER FURNISHED) SECURE WITH THESE NUTS AFTER TENSIONING TENSION GUYS WITH THES GUY CABLE (WDZP) CUT OFF EXCESS WRAP FIVE OR MORE TIMES EGG INSULATOR (E VERTICAL GUY SUPPORT FIGURE 4 GUY ASSEMBLY Cut four pieces of guy cable .762M (30”) and two pieces 2.082M (82”).
- Page 7 CB FREQUENCIES (11 METER BAND) 3rd DIR REFL DRIVEN 1 st DIRECTOR 2nd DIRECTOR “A” “B” CHANNEL FREQUENCY 5 . 6 3 8 ~ l - 3 ( 2 2 2 ” ) ( 7 5 ” ) 5 . 6 3 8 ~ 4 - 7 ( 2 2 2 ”...
- Page 8 REFER TO THE INSTRUCTIONS ON ADJUSTINNG THE S.W.R. TO DETERMINE EXACT SETTINGS. THERE ARE2 SEPARATEGAMMA ADJUSTMENTS, 1. CAPACI- TOR ADJUSTMENT, 2. SLIDER POSITION. DO NOT MOVE BOTH AT THE SAME TIME. MOVE THE CAPACITOR FIRST, THEN, IF NECESSARY MOVE THE SLIDER, AND GO BACK TO THE CAPACITOR. S21, Nil, N12-7 DRIVEN LK.
- Page 9 I n s t a l l i n g a n d r i g g i n g t o w e r s , m a s t s a n d a n t e n n a s r e q u i r e s p e c i a l i z e d s k i l l s a n d e x p e r i e n c e . I n f o r m a t i o n s u p p l i e d b y M a s s u m e s t h a t a l l p r o d u c t s w i l l b e i n s t a l l e d b y p e r s o n n e l h a v i n g t h e s e s k i l l s a n d h a v e i n s t a l l e d s i m i l a r p r o d u c t s b e f o r e .
Need help?
Do you have a question about the M105HV and is the answer not in the manual?
Questions and answers