Download Print this page
Maco Antennas FLAT 8 Assembly Instructions Manual

Maco Antennas FLAT 8 Assembly Instructions Manual

8 element 10/11 meter beam

Advertisement

Quick Links

Assembly Instructions
FLAT 8
8 ELEMENT 10/11 METER BEAM
Maco Antennas - a Division of Charles Electronics, LLC
302 S. East St.
Mt. Carroll, IL 61053
815-244-3500
www.macoantennas.net

Advertisement

loading
Need help?

Need help?

Do you have a question about the FLAT 8 and is the answer not in the manual?

Questions and answers

Summary of Contents for Maco Antennas FLAT 8

  • Page 1 Assembly Instructions FLAT 8 8 ELEMENT 10/11 METER BEAM Maco Antennas - a Division of Charles Electronics, LLC 302 S. East St. Mt. Carroll, IL 61053 815-244-3500 www.macoantennas.net...
  • Page 2 WHEN ORDERING PARTS, ALWAYS GIVE PART NUMBER AND DESCRIPTION. Please note: In an effort to keep the price on Maco Antennas down, we have decided not to clean up all the burrs and rough edges on the parts. We recommend that you deburr and clean up each part with files, sandpaper, etc. so that they go together easily. We are aware this needs to be done but have elected not to do it to save you the money we would have to add to the price of the kit for this service.
  • Page 3: Metal Parts

    FLATSIDER 8 ADDITIONS to the LASER 500 INSTRUCTIONS (These instructions MODIFY THE LASER 500 INSTRUCTIONS attached.) 1 - THE DIFFERENCE The FLATSIDER 8 is the LASER 500 with three changes: (1) The vertical elements and associated hardware are removed. (2) A 5000 Watt Gamma Assembly is included. (3) The Reflector (screen) is redesigned with the addition of 2 more wires, which some claim increases the rejection.
  • Page 4 2B. CAUTION: TAKE CARE TO AVOID ANY CONTACT WITH OVERHEAD POWER LINES WHEN RAISING YOUR ANTENNA. SERIOUS OR FATAL INJURY COULD RESULT. Maco Antennas - a Division of Charles Electronics, LLC 302 S. East St. Mt. Carroll, IL 61053 815-244-3500...
  • Page 5 ELEMENT ASSEMBLY FIGURE 3 Prior to assembling elements slide a boom-to-element mount (BE3P) onto each of the (16) element center sections (TIIP). Assemble each element as shown using the clamps and hardware specified. Refer to the element table to determine dimensions for each element. Install a black plastic cap (PL2) onto both ends of each element. Assemble the reflector elements in the same manner.
  • Page 6 R E F L E C T O R ( S E E F I G . 38) D R I V E N E L E M E N T S P L A S T I C C A P G A M M A MAT (SEE FIG.
  • Page 7 - e----s S28. N15, N16, N17P, 3 l/2” x 112’ HEX. HD. BOLT, (3) l/2” FLAT WASHERS, T39 - 20” A T CENTER: B O O M S U P P O R T 2” U-BOLTS 8. S A D D L E S 2”...
  • Page 8 16’ 9” 5’ 4-l/2” 16’ 8” C L A M P WITH X10-24 x112” C L A M P WI1 H #llJ-24 x1/2’ S C R E W 8. SQ. NUT 16’ 8” 1 16’ 8” 5’ 4” C T O R 16’...
  • Page 9 THESE DIMENSONS ARE APPROXI- NOTE. ACT SETTINGS. THERE ARE 2 SEPARATE GAMMA ADJUSTMENTS, I. CAPACITOR AD- JUSTMENT, 2. SLIDER POSI’I‘ION. DO NOT MOVE BOTH AT THE SAME TIME. MOVE THE CAPACITOR FIRST, THEN, IF NEC- ESSARY MOVE THE SLIDER, AND GO BACK TO S T R A P S ( I N S T A L L F L U S H A G A I N S T B O O M - T O - E L E M E N T...
  • Page 10 I n s t a l l i n g a n d r i g g i n g t o w e r s , m a s t s a n d a n t e n n a s r e q u i r e s p e c i a l i z e d s k i l l s a n d e x p e r i e n c e . I n f o r m a t i o n s u p p l i e d b y M a s s u m e s t h a t a l l p r o d u c t s w i l l b e i n s t a l l e d b y p e r s o n n e l h a v i n g t h e s e s k i l l s a n d h a v e i n s t a l l e d s i m i l a r p r o d u c t s b e f o r e .