Crown Bus Wiring For 5-Pin Din Input; Crown Bus Wiring For 4-Pin Din Output - Crown AMB-5 Hardware Installation Manual

Crown Bus Barrier Block
1 2 3 4
The Crown Bus connector
shown here is the standard
connector found on the back
panel of most mixers and SLM.
PIN
Output (+) 1
Output (–) 2
Input (+) 3
Input (–) 4
GND
Fig. 3.7 Crown Bus Wiring for 5-pin DIN Input
Figure 3.9 Crown Bus Wiring ÷Loopsš from Output to Input of Each IQ Component
Page 14
Crown Bus 5-pin DIN Input
1
5
2
4
3
The female Crown Bus connector shown
here can be found on the back panel
of IQ-INT IIs and most IQ-P.I.P.s.
PIN
5
(Not Used)
4 (Not Used)
3 GND
2 Input (+)
1 Input (–)
TO HOST COMPUTER
5 OUT
4 OUT IN
3 OUT IN
2 OUT IN
1 OUT IN
POWER IN
IQ INTERFACE
AUDIO ADD 25
AUDIO STACK
BUS AUDIO STACK 0 5 FOR MIC
CROWN IN IN
IN OUT -5 10
OUT
120 VAC SERIAL DATA LOOP 6
AUX 1 -10
2 15
60 Hz CTRL
BUS -12 21
BUS MAIN
MAIN
L
M
+ –
– + –
– + – +
20 W +
RS232 / RS422
AUDIO ADD 25
AUDIO STACK
AUDIO STACK 0 5 FOR MIC
CROWN BUS IN
OUT IN -5
OUT IN 10
SERIAL DATA LOOP 6
120 VAC AUX 1
2 -10 15
60 Hz
CTRL -12 21
MAIN BUS
MAIN BUS
M L
+ – + –
+ – + –
20 W + –
RS232 / RS422
AUDIO
STACK ADD 25
STACK AUDIO
BUS AUDIO IN 0 5 FOR MIC
CROWN IN
IN OUT -5 10
OUT
120 VAC AUX SERIAL DATA LOOP 6
1 -10 15
2
60 Hz CTRL
BUS -12 21
BUS MAIN
MAIN
M L
– + –
– + – +
+ – +
20 W
RS232 / RS422
IQ Mixer / Multiplexer Hardware Installation
Crown Bus 4-pin DIN Output
4
3
The female Crown Bus connector shown
here can be found on the back panel
of IQ-INT IIs and most IQ-P.I.P.s.
PIN
(Not Used) 4
(Not Used)
3
Output (+) 2
Output (-) 1
Fig. 3.8 Crown Bus Wiring for 4-pin DIN Output
OUT
OUT IN 8
6 OUT IN 7
IN
COMPUTER
AUDIO ADD 25
AUDIO ADD 25
AUDIO 0 5 FOR MIC
ADD 25 0 FOR MIC IN
AUDIO ADD 25 IN 5 -5
AUDIO ADD 25 IN 0 5 FOR MIC 10
0 5 FOR MIC -5 10 1
0 5 FOR MIC IN -5 10 2
IN -5 10 -10 15
-5 10 3 -10 15
4 -10 15 21
5 -10 21 -12
-10 15 21 -12
15 -12
-12 21
-12 21
M L P
M L P
M L P
M L P
M L P
P + –
+ –
+ –
+ –
+ –
AUDIO ADD 25
AUDIO ADD 25
AUDIO ADD 25 0 5 FOR MIC
AUDIO ADD 25 0 5 FOR MIC IN
AUDIO ADD 25 0 5 FOR MIC IN -5 10
0 5 FOR MIC IN -5 10
0 5 FOR MIC IN -5 1
IN -5 10 2 -10
-5 10 3 -10 15
10 4 -10 15
5 -10 15 -12 21
15 -12 21
-10 15 -12 21
-12 21
-12 21
M L P
L P
L P M
P M
M L
M L P + –
P + –
–
– +
– +
+
AUDIO ADD 25
AUDIO ADD 25
AUDIO ADD 25 0 5 FOR MIC
AUDIO ADD 25 0 5 FOR MIC IN
AUDIO 0 5 FOR MIC IN -5
ADD 25 0 5 FOR MIC IN -5 10
IN -5 10 1
IN 0 5 FOR MIC 10 2 -10
-5 10 3 15
-5 10 4 -10 15
5 -10 15 -12 21
-10 15 -12 21
-10 15 -12 21
21
21 -12
-12
M L P
M L P
M L P
M L P
M L P –
P – +
+
+ –
+ –
+ –
BALANC ED INPUTS
CH–1
CH–2
AUX DSPI
SERIAL IN
SERIAL OUT
3
INVERT NON-
(–)
INVERT
(+)
1 2
GND
BALANC ED INPUTS
CH–1
CH–2
DSPI
AUX
SERIAL IN
SERIAL OUT
INVERT 3
NON-
(–)
INVERT
(+)
1
2
GND
BALANC ED INPUTS
CH–1
CH–2
DSPI
AUX
SERIAL IN
SERIAL OUT
INVERT 3
NON-
(–)
INVERT
(+)
1 2
GND
Crown Bus Barrier Block
1
1 2 3 4
2
The Crown Bus connector
shown here is the standard
connector found on the back
panel of most mixers and SLM.
PIN
1
2
3
4
Optional Shield
Important: Provide ad-
equate cooling if the unit
will be used in a hot envi-
ronment.
empty rack space (1.75
inches or 4.4 centime-
ters) between each unit if
more than four units will
be stacked in a cabinet.
Each empty rack space
should be sealed with a
blank rack panel to facili-
tate proper air flow inside
the cabinet.
Output (+)
Output (–)
Input (+)
Input (–)
GND
Allow one
Rev. 0