Cutting Angle Adjustment - Makita LW1400 Instruction Manual

6ZLWFK DFWLR
:
Before plugging in the tool,
DOZD V FKHFN WR VHH WKDW WKH VZLWFK WULJJHU DFW
ates properly and returns to the "OFF" position
ZKH UHOHDVHG
► )LJ
Lock button / Lock-o button
WULJJHU
)RU WRRO ZLWK ORFN E WWR
7R VWDUW WKH WRRO VLPSO S OO WKH V LW K WULJJHU 5HOHDVH
the switch trigger to stop. For continuous operation,
pull the switch trigger, push in the lock button and then
UHOHDVH WKH V LW K WULJJHU 7R VWRS WKH WRRO IURP WKH
OR NHG SRVLWLR S OO WKH WULJJHU I OO WKH UHOHDVH LW
Switch can be locked in "ON" posi
WLR IRU HDVH RI RSHUDWRU FRPIRUW G UL J H WH GHG
use. Apply caution when locking tool in "ON"
position and maintain rm grasp on tool.
For tool with lock-o button
To prevent the switch trigger from being accidentally
pulled, a lock-o button is provided. To start the tool,
press the lock-o button and pull the switch trigger.
5HOHDVH WKH V LW K WULJJHU WR VWRS
:
NEVER defeat the lock-o button
E WDSL J GRZ RU VRPH RWKHU PHD V
a negated lock-o button may result in unintentional
operation and serious personal injury.
:
1(9(5 VH WKH WRRO LI LW U
R VLPSO S OO WKH VZLWFK WULJJHU ZLWKR W SUHVV
ing the lock-o button. V LW K L
PD UHV OW L L WH WLR DO RSHUDWLR D G VHULR V
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
'R RW S OO WKH VZLWFK WULJJHU KDUG
without pressing in the lock-o button. 7KLV D
cause switch breakage.
Interval between vise and guide
SODWH
After adjusting the interval
between the vise and the guide plate, make
V UH WKDW WKH J LGH SODWH LV SURSHUO VHF UHG
Insu cient xing may result in personal injury.
The following interval settings of the vise are available:
PP RULJL DO VHWWL J
PP
PP
If your work requires di erent setting, proceed as fol
OR V WR KD JH WKH VSD L J RU L WHU DO
)RU /:
/RRVH WKH V UH R WKH J LGH SODWH 0R H WKH J LGH
SODWH WR WKH GHVLUHG SRVLWLR WKH WLJKWH WKH V UH
► )LJ 6 UH LGH SODWH
)RU /:
Remove the two hex bolts using a socket wrench. Move
WKH J LGH SODWH WR WKH GHVLUHG SRVLWLR D G VH
the hex bolts.
► )LJ

Cutting angle adjustment

6 LW K
J LGH SODWH PDNH V UH WKDW WKH J LGH SODWH LV
SURSHUO VHF UHG Insu cient xing may result in
personal injury.
the material is not rmly secured with the vise
EHFD VH RI WKH F WWL J D JOH
)RU /:
7 U WKH OH HU R
WR WKH GHVLUHG D JOH D G I OO WLJKWH WKH OH HU
► )LJ
)RU /:
DOZD V VHW WKH J LGH SODWH DW
6HWWL J DW WKH
hinders the movement of stopper plate, which
UHV OWV L D IDLO UH F W
V LW K LWK
Loosen the two hex bolts using a socket wrench. Turn
WKH J LGH SODWH WR WKH GHVLUHG D JOH D G VH
the hex bolts. Be careful not to move the set angle while
V ZKH
securing the hex bolts.
► )LJ
HHG RI UHSDLU
127( 7KH V DOH R WKH J LGH SODWH LV R O D UR JK
indication. For more accurate angle, use a protractor
RU WULD JOH U OHU .HHS WKH KD GOH GR
cut-o wheel extends into the base. At the same time,
adjust the angle between the guide plate and the cut-
o wheel with a protractor or triangle ruler.
Spark guard adjustment
For LW1401 only (country speci c)
► )LJ
7KH VSDUN J DUG LV ID WRU L VWDOOHG LWK LWV OR HU HGJH
contacting the base. Operating the tool in this position
will cause many sparks to y around. Loosen the screw
and adjust the spark guard to a position at which mini
mum sparks will y around.
6WRSSHU SODWH
For LW1401 only (country speci c)
► )LJ
The stopper plate prevents the cut-o wheel from
contacting the workbench or oor. When a new cut-o
KHHO LV L VWDOOHG VHW WKH VWRSSHU SODWH WR SRVLWLR
When the cut-o wheel wears down to the extent that
WKH OR HU SRUWLR RI WKH RUNSLH H LV OHIW
VWRSSHU SODWH WR SRVLWLR
DSD LW
1 6
LGH SODWH Hex bolts
After adjusting the angle of the
'R RW RSHUDWH WKH WRRO ZKH
WHU OR N LVH 0R H WKH J LGH SODWH
LGH SODWH /H HU
:KH SHUIRUPL J ULJKW PLWHU F W
PP SRVLWLR
PP RU PP SRVLWLR
LGH SODWH Hex bolts
VR WKDW WKH
6 UH 6SDUN J DUG
6WRSSHU SODWH
WR DOOR L UHDVHG
LWK D RU GR KHHO
UH LW LWK
UH LW LWK
W VHW WKH
WWL J