Sony UDA-1 Service Manual page 61

DIGITAL BOARD IC501 MK60FN1M0VLQ12 (USB CONTROLLER)
Pin No. Pin Name
1 to 4 PTE0 to PTE3
5 VDD
6 VSS
7, 8 PTE4, PTE5
9 I2S0_MCLK
10 to 12 PTE7 to PTE9
13 I2S0_TXD0
14 I2S0_TX_FS
15 I2S0_TX_BCLK
16 VDD
17, 18 VSS
19 USB0_DP
20 USB0_DM
21 VOUT33
22 VREGIN
23 PGA2_DP
24 PGA2_DM
25 PGA3_DP
26 PGA3_DM
27 PGA0_DP
28 PGA0_DM
29 PGA1_DP
30 PGA1_DM
31 VDDA
32 VREFH
33 VREFL
34 VSSA
ADC1_SE16,
35, 36
ADC0_SE16
37 VREF_OUT
DAC0_OUT,
38, 39
DAC1_OUT
40 XTAL32
41 EXTAL32
42 VBAT
43 VDD
44 VSS
45 to 48 PTE24 to PTE27
49 PTE28
JTAG_TCLK/
50
EZP_CLK
51 JTAG_TDI/EZP_DI
52 JTAG_TDO/EZP_DO
53 JTAG_TMS
54 LLWU_P3/EZP_CS_b
55 JTAG_TRST_b
56 VDD
57 VSS
58 ULPI_CLK
59 ULPI_DIR
60 ULPI_NXT
61 ULPI_STP
ULPI_DATA0,
62, 63
ULPI_DATA1
64 to 69 PTA12 to PTA17
70 VDD
71 VSS
72 PTA18
73 PTA19
I/O
- Not used
- Power supply terminal (+3.3V)
- Ground terminal
- Not used
O I2S master clock signal output to the digital audio interface receiver
- Not used
O I2S serial data output to the digital audio interface receiver
O I2S L/R sampling clock signal output to the digital audio interface receiver
O I2S bit clock signal output to the digital audio interface receiver
- Power supply terminal (+3.3V)
- Ground terminal
- Not used
- Not used
O Not used
I Not used
- Not used
- Not used
- Not used
- Not used
- Not used
- Not used
- Not used
- Not used
- Power supply terminal (+3.3V)
I Reference voltage (+3.3V) input terminal
I Reference voltage input terminal
- Ground terminal
- Not used
O Reference voltage output terminal
- Not used
O System clock output terminal
I System clock input terminal
- Power supply terminal (+3.3V)
- Power supply terminal (+3.3V)
- Ground terminal
- Not used
O Reset signal output to the USB transceiver
- Not used
- Not used
- Not used
- Not used
- Not used
- Not used
- Power supply terminal (+3.3V)
- Ground terminal
O Clock signal output to the USB transceiver
I DIR signal input from the USB transceiver
I NXT signal input from the USB transceiver
O STP signal output to the USB transceiver
I/O Two-way ULPI data bus with the USB transceiver
- Not used
- Power supply terminal (+3.3V)
- Ground terminal
O System clock output terminal (12 MHz)
I System clock input terminal (12 MHz)
Description
Fixed at "L" in this unit
Not used
Not used
Not used
"L": reset
UDA-1
61