Page 1
User Manual Model ID: MAVERICKSTORM3BEAMWASH...
Page 2
Edition Notes The Maverick Storm 3 BeamWash User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the Maverick Storm 3 BeamWash as of the release date of this edition. Trademarks Chauvet, Chauvet Professional, the Chauvet logo, Maverick, and Maverick Storm 3 BeamWash are registered trademarks or trademarks of Chauvet &...
Any reference to data or power connections in this manual assumes the use of Seetronic IP-rated cables. The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data transmission protocol. Maverick Storm 3 BeamWash User Manual Rev. 3...
• In the event of a serious operating problem, stop using immediately. If a Chauvet product requires service, contact Chauvet Technical Support. Maverick Storm 3 BeamWash User Manual Rev. 3...
The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity. Maverick Storm 3 BeamWash User Manual Rev. 3...
Dual mode operation enables pixel-mapped eye candy to run under ArtNet/sACN control with separate assignment of motorized functions to DMX. Housed in an advanced IP65-rated alloy body, Maverick Storm 3 BeamWash is built with the durability and versatility to perform in any venue, indoors or out.
19 in 482 mm 10 in 254 mm 15.9 in 404 mm 20.8 in 527 mm 4.6 in 117 mm 18.3 in 465 mm 14.8 in 375 mm 11.9 in 303 mm Maverick Storm 3 BeamWash User Manual Rev. 3...
Green/Yellow Green/Yellow Green Power Linking It is possible to power link Maverick Storm 3 BeamWash products. See the table below for the current draw at each voltage and frequency: 100 V, 60 Hz 120 V, 60 Hz 208 V, 60 Hz...
DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com. DMX Linking The Maverick Storm 3 BeamWash can link to a DMX controller using a 5-pin DMX connection or a WDMX connection. For more information about DMX, read the DMX primer at: https://www.chauvetprofessional.com/wp-content/uploads/2016/06/DMX_Primer.pdf.
To other Art-Net™ or sACN devices USB Software Update The Maverick Storm 3 BeamWash allows for software updates with a USB device using the built-in USB port. To update the software using a USB flash drive, do the following: 1. Power on the product, and plug the flash drive into the USB port.
The technician mode disables the pan/tilt motors, allowing the output of the product to be aimed by hand. To enable the technician mode of the Maverick Storm 3 BeamWash, hold <UP> and <LEFT> while the product is powering on. When the product is turned off and back on, the pan and tilt will return to normal function.
Operation Menu Map Refer to the Maverick Storm 3 BeamWash product page on www.chauvetprofessional.com for the latest menu map. Programming Levels Description Control Settings Control Settings Main Level Basic Standard Advanced Sets the DMX personality: Personality Tour (see Control Personalities)
Page 15
Personality Standard (see Control Personalities) sACN Advanced Start Address 1–512 Sets the sACN starting address Universe 0–255 Sets the sACN universe Basic Sets the Kling-Net personality: Kling-Net Personality (see Control Personalities) Standard Maverick Storm 3 BeamWash User Manual Rev. 3...
Page 16
Do not swap pan and tilt Swap XY Pan controls tilt, tilt controls pan Lock the buttons and touch screen Lock Screen Passcode: 0920 Do not reset WDMX WDMX Reset Reset WDMX Maverick Storm 3 BeamWash User Manual Rev. 3...
Page 17
Maverick Storm 3 BeamWash products in the DMX daisy chain USB Update Update firmware via USB-C Pan/Tilt Reset individual functions or all Reset Function Zoom functions from start-up Factory Reset to factory default settings Settings Maverick Storm 3 BeamWash User Manual Rev. 3...
Page 18
_ _ _ _ Base Fan2 Speed _ _ _ _ Base Fan3 Speed _ _ _ _ Base Fan4 Speed _ _ _ _ Error No Error!* Shows any errors, or No Error! Information Maverick Storm 3 BeamWash User Manual Rev. 3...
Page 19
Dimmer Fine (all, 1–28) Red (all, 1–28) Red Fine (all, 1–28) Green (all, 1–28) Green Fine (all, 1–28) Blue (all, 1–28) Blue Fine (all, 1–28) White (all, 1–28) White Fine (all, 1–28) Maverick Storm 3 BeamWash User Manual Rev. 3...
Use control configurations to operate the product with a DMX, WDMX, Art-Net™, Kling-Net, and sACN control signals. Control Mode The Maverick Storm 3 BeamWash works with wired DMX, WDMX, Art-Net™, Kling-Net, and sACN control signals. To select which single control protocol to use: 1. Go to the Control Settings main level.
3. Set the 4 values of the IP address from 000–255. Subnet Mask To set the subnet mask: 1. Go to the Network Setting level. 2. Select the SubMask option. 3. Set the 4 values of the subnet mask from 000–255. Maverick Storm 3 BeamWash User Manual Rev. 3...
000 255 0–100% – – 26 Main blue fine 000 255 0–100% – 27 Main white 000 255 0–100% – – 28 Main white fine 000 255 0–100% Maverick Storm 3 BeamWash User Manual Rev. 3...
110 124 Random strobe, fast to slow 225 229 On 125 129 On 230 244 Pulse strobe 2, fast to slow 130 144 Random 100–0% strobe, fast to slow 245 255 On Maverick Storm 3 BeamWash User Manual Rev. 3...
When preset color HTP is on, manual color controls may be used at the same time as preset color controls. When preset color HTP is off, preset color controls will override all manual color controls. Maverick Storm 3 BeamWash User Manual Rev. 3...
3. Select from NO or YES. WDMX Reset To reset the WDMX connection: 1. Go to the Setup main level. 2. Select the WDMX Reset option. 3. Select from NO or YES. Maverick Storm 3 BeamWash User Manual Rev. 3...
2. Select the Calibrated White option. 3. Select from ON (uses the factory-calibrated white balance), OFF (uses the maximum white values), or Custom (uses the custom white values defined under White Balance) Maverick Storm 3 BeamWash User Manual Rev. 3...
2. Select the Preset Sync option. 3. Select NO or YES. • To sync other Maverick Storm 3 BeamWashes, connect those products via DMX cable. • The product can be in any control mode except WDMX. ArtNet, DMX, sACN are all acceptable.
3. Select NO (to cancel) or YES (to reset the product configuration). Test Mode Auto Test To have the Maverick Storm 3 BeamWash automatically test all functions one after the other: 1. Go to the Test Mode main level. 2. Select the Auto Test option.
Operation Web Server The Maverick Storm 3 BeamWash Web Server can be accessed by any computer on the same network as the product. It allows network access to system information, settings such as control setup, manual testing of all functions, firmware updates, and the ability to change the Web Server password.
To ensure that the product has been reassembled correctly, use the IP Tester from Chauvet Professional to check the following data has the given measurements for the given method: Parameters Values Method Positive Test pressure 2.18 kPa Test duration 60 seconds PASS state leak pressure <0.02 kPa Maverick Storm 3 BeamWash User Manual Rev. 3...
This is to prevent undue stress on the tilt locks and limit the amount of off-axis bounce on internal components. Maverick Storm 3 BeamWash User Manual Rev. 3...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. Maverick Storm 3 BeamWash User Manual Rev. 3...