Page 2
Edition Notes The Intimidator Spot 475ZX User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the Intimidator Spot 475ZX as of the release date of this edition. Trademarks Chauvet, Chauvet DJ, the Chauvet logo, and Intimidator are registered trademarks or trademarks of Chauvet &...
Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. Intimidator Spot 475ZX User Manual Rev. 1...
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the user. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Intimidator Spot 475ZX User Manual Rev. 1...
260 mm 13.1 in 333 mm 11.2 in 284 mm 21.9 in 555 mm 14.3 in 363 mm 8.3 in 212 mm 13.1 in 333 mm 20.9 in 531 mm 9.8 in 250 mm Intimidator Spot 475ZX User Manual Rev. 1...
It is possible to link up to 3 Intimidator Spot 475ZX products on 120 VAC or up to 7 products on 230 VAC. The power-linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, consult with the local Chauvet distributor, as power linking connectors and requirements may differ by country or region.
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator Spot 475ZX may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming.
This provides a layer of protection against the high temperature from the lamp. • All custom gobos in the Intimidator Spot 475ZX gobo wheel 1 must be aluminum or glass. Procedure Follow the recommended procedure below to remove or replace the gobos: 1.
Press to scroll down the list of options or to find a lower value <ENTER> Press to activate a menu option or a selected value Menu Map Refer to the Intimidator Spot 475ZX product page on www.chauvetdj.com for the latest menu map. Main Level...
Page 14
Running Mode _ _ _ _ _ _ Displays the current running mode Sys Info DMX Address _ _ _ Displays the current DMX address Temperature _ _ _ Displays the current product temperature Intimidator Spot 475ZX User Manual Rev. 1...
Operation DMX Configuration The Intimidator Spot 475ZX works with a DMX controller. Information about DMX is in the Chauvet DMX Primer available from the Chauvet website: chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf. Starting Address The Intimidator Spot 475ZX uses up to 16 DMX channels, which defines the highest recommended address to 497.
Reverse cycle effect, slow to fast 000 063 Gobo indexing 064 147 Gobo rotation, slow to fast Gobo rotation 148 231 Reverse gobo rotation, slow to fast 232 255 Gobo bounce, short to long Intimidator Spot 475ZX User Manual Rev. 1...
Page 17
000 003 004 007 008 076 Strobe, slow to fast Shutter 077 145 Pulse strobe, slow to fast 146 215 Random strobe, slow to fast 216 255 Intimidator Spot 475ZX User Manual Rev. 1...
Page 18
184 199 Sound-active movement macro 4 200 215 Sound-active movement macro 5 216 231 Sound-active movement macro 6 232 247 Sound-active movement macro 7 248 255 Sound-active movement macro 8 Intimidator Spot 475ZX User Manual Rev. 1...
DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Automatic Programs To run the Intimidator Spot 475ZX in automatic mode, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Run Mode.
6. Use <UP> or <DOWN> to select from 540 (540°), 360 (360°), or 180 (180°). 7. Press <ENTER>. Tilt Angle To set the tilt angle range on the Intimidator Spot 475ZX, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup.
The product will only respond to low frequencies of music (bass and drums). DMX Loss To set the action the Intimidator Spot 475ZX will do when signal is lost, do the following: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup.
Operation To access the instructions on how to bind the RF remote to the Intimidator Spot 475ZX, do the following: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup. 3. Press <ENTER>. 4. Use <UP> or <DOWN> to select RF.
The Master/Slave mode allows a single Intimidator Spot 475ZX product (the “master”) to control the actions of one or more Intimidator Spot 475ZX products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in standalone mode, while the slave products will be set to operate in slave mode.
Operation Zero Adjust Mode The Intimidator Spot 475ZX contains a passcode-protected mode that allows the user to calibrate and adjust several of the product’s operating parameters. In order to access this mode, do the following: 1. Press and hold <MENU> for at least 3 seconds.
Operation RFC Remote Control The Intimidator Spot 475ZX can be operated with an RFC remote (comes with Intimidator Spot 475ZX) or an RFC-XL remote (sold separately). To enable RF control, follow the instructions below: 1. Press <MENU> repeatedly until Run Mode shows on the display.
(needle tip applier recommended). Make sure the gobo holder is rotating freely and is not making any abnormal noise. 8. Reinstall the gobos in the gobo holder. Make sure the gobos are in the correct positions. 9. Reinstall the gobo holder in the unit. Intimidator Spot 475ZX User Manual Rev. 1...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. Intimidator Spot 475ZX User Manual Rev. 1...