Page 1
User Manual English 1450 Coin Counter & Sorter...
Page 2
Click here to open a printable version of the manual in the selected language. Introduction Thank you for purchasing the Safescan 1450 coin counter and sorter. For proper use and maintenance, we advise to read this user manual carefully. Please note...
- To prevent fire or short circuit, unplug the unit if you want to move it to another position. - Hold the plug disconnecting the unit from the power outlet, never pull the cord. More info, articles, tutorials and videos support.safescan.com...
QR code with your smart product registration benefits, please Safescan® is a registered trademark of Solid Control Holding B.V. No information may be reproduced in any form, by print, copy or in any other way without prior written device or visiting: scan the QR code on the right or visit: permission of Solid Control Holding B.V.
Page 5
(not for lifting the machine!) 4. Coin cups 5. Grip area to lift the machine Back 6. Safety lock 7. Power switch 8. Mains power connector 9. Fuse 10. Product label 11. Print port connector (RJ-10) More info, articles, tutorials and videos support.safescan.com...
2. Switch on the counter with the power switch located at the back. 3. The counter performs a self-test. The display will show the firmware version. 4. When display shows 0 pcs / 0.00 the device is ready for counting coins. WAIT More info, articles, tutorials and videos support.safescan.com...
Press once: Increase n.a. Deactivate value with 1. batch Press and hold: counting Increase value in steps of 10 n.a. Decrease value with n.a. 1. Press and hold: decrease value in steps of 10 More info, articles, tutorials and videos support.safescan.com...
Toggle between Time & Date settings Display overview BAT ON REPORT 3880 1. Total number of coins counted 2. Total value of coins counted 3. Batch function is activated 4. Report function is activated More info, articles, tutorials and videos support.safescan.com...
English First operation Please note The 1450 counts Euro coins only. Ensure that no foreign objects or coins of other currencies enter the machine - this will cause the machine to malfunction. 1. Put the coins in the hopper. Do not exceed the ‘full line’ as indicated inside the hopper.
Page 10
4. The coins are sorted on diameter, from large (left) to small (right). € 2 - € 0.50 - € 1 - € 0.20 - € 0.05 - € 0.10 - € 0.02 - € 0.01 More info, articles, tutorials and videos support.safescan.com...
The batch function is used to create a fixed number of coins and can be set per denomination. In counting mode, press [+] to activate or deactivate batch counting. BAT ON will be shown on the display. BAT ON More info, articles, tutorials and videos support.safescan.com...
Page 12
Counting stops after 20 coins of 5 cents If during counting the batch amount of a coin denomination is reached, the 1450 will stop. Press [START] to resume counting. BAT ON Counting stops at 20 pcs of 5 cent coins...
Page 13
Press and hold the [CLEAR] button for approx. 2 seconds to clear all set batch amounts. Maximum number of coins per cup To prevent overflow, the Safescan 1450 will stop automatically when the maximum number of coins per cup has been reached. Coin Denomination Maximum per cup €...
Page 14
Year setting. Press [+] and [-] to adjust the value. Press [PRINT/>] to toggle between year (Y), month (M), day (D) and time. DATE DATE y 2018 DATE TIME 10:07 More info, articles, tutorials and videos support.safescan.com...
‘open’ position OLOAD1 Something is stuck inside Remove the object of the device and may be that is causing blocking its internal parts the blockage (see chapter: Removing a jammed item) More info, articles, tutorials and videos support.safescan.com...
Before cleaning ALWAYS, unplug the Safescan 1450 coin counter from the mains outlet. Removing the transport assembly 1. Slide the safety lock switch on the back to the ‘open’ position.
Page 17
Clean the sensors located inside the sorting holes. In addition, the transport rail should also be cleaned. 1. Clean the transport assembly with cleaning brush and/or compressed air 2. Clean the coin transport area Coin compartment Sorting holes More info, articles, tutorials and videos support.safescan.com...
Page 18
Place the cover back on the device and slide the safety- lock switch on the back to the ‘locked’ position. Place the coin cups back. Connect the device to the mains outlet and switch it on. More info, articles, tutorials and videos support.safescan.com...
Page 19
‘’OLOAD1’’. Please follow the instructions below to remove the jammed item. 1. Error message OLOAD1 2. Switch off the device (1) and is shown. remove the power cord (2). More info, articles, tutorials and videos support.safescan.com...
Page 20
( 1- 2 ). (position 1 or 2) for later. 5. Remove the sorting ring by pushing it down (1) and turning it (2) until the screw is located in the middle (3). More info, articles, tutorials and videos support.safescan.com...
Page 21
1 and 2. 8. You can now mechanism to 9. Carefully remove the jammed create space. Please note item. that the screws will stay attached to the metal mechanism. More info, articles, tutorials and videos support.safescan.com...
Page 22
11. Use a screwdriver to secure you can place the the screws marked 1 and 2, mechanism back. back into place. 12. Place the sorting ring back in the device with the screw positioned in the middle. More info, articles, tutorials and videos support.safescan.com...
Page 23
Place note Please note that the instructions above only apply to the Safescan 1450 models that have the serial number 112059919180001 or higher. More info, articles, tutorials and videos support.safescan.com...
Page 24
You can also press the [START] button to bypass the “POS 2” message and start a counting process, but when you next time switch on the device, you will receive the above message again. More info, articles, tutorials and videos support.safescan.com...
Page 25
The following message will appear: This indicates that the transport assembly needs to be replaced. The assembly can be ordered as sparepart from Safescan. To change the transport assembly: Switch off the machine, open the machine as described in chapter “Removing the transport assembly”.
Otherwise there is a risk of life due to electrical shock. Remove the fuse cover and replace the fuse with an equivalent fuse. The lock of the fuse must be firmly pressed again after changing. More info, articles, tutorials and videos support.safescan.com...
Page 27
English Use in combination with Safescan TP-230 printer The Safescan 1450 can also be used in combination with the optional Safescan TP-230 thermal printer. This enables you to make an instant printout of your counting results. Safescan 1450 Safescan Safescan...
100 - 240 V / 50 – 60 Hz Power consumption: max. 60 W Operating temperature: 0°C – 40°C Humidity: 30 - 75 % Dimensions: 29 x 31 x 29 cm Weight: 6.85 kg More info, articles, tutorials and videos support.safescan.com...
Page 29
Safescan is a registered trademark of Solid Control Holding B.V. ® No part of this manual may be reproduced in any form, by print, copy or in any other way without prior written permission of Solid Control Holding B.V. Solid Control Holding B.V.