Preparing The Installation; Wiring Table - Viking C-3000 Technical Practice

I n s t a l l a t i o
I n s t a l l a t i o
A. Definitions
Master Module: The C-3000 module assigned module ID #1. Also, the only module in a single-module system.
Slave Module(s): Any module(s) in addition to the Master, in a multi-module C-3000 system. Slave modules are
assigned module ID numbers in the range of #2 through #8.
"66" Punchdown Terminal Block: A connection peripheral used to interface telephone lines easily. This installation
requires a "split" punchdown block.
B. Preparing the Installation
Select an appropriate location in which to install the C-3000 System. It is normally most convenient to install the C-3000
modules as near as possible to the telco demarcation point; that is, the common point at which all tenant phone lines
enter the building (if applicable). If the tenant phone wiring is not currently cabled though a "66" block or blocks, it will
be necessary to install "66" block(s) at this time to facilitate the installation of the C-3000 system. Note: See the instal-
lation diagram on the following page for recommendations on which "66" block to use.
C. Assigning Module ID Numbers
A C-3000 system consists of at least one (Master) C-3000 module, and as many as seven (7) Slave modules. Multiple
C-3000 modules are all interconnected from module to module, using the supplied modular cords, connecting the
MULTI-MODULE INTERCONNECTS from IN to OUT. If more than one C-3000 module is being installed, it will be nec-
essary to set module ID numbers at this time. Each C-3000 module must have it's own ID number to be part of a C-
3000 system. Module ID numbers are set using the three-position DIP switches on the front of the C-3000 modules
(see diagram below). Module ID numbers are used to determine which C-3000 module is responsible for handling a
particular range of apartment numbers. As an example, Module #1 (the Master module) handles apartment numbers 1-
12, Module #2 handles apartment numbers 13-24 and so forth.
D. Wiring Table
Refer to the wiring table below when installing the cabling for the C-3000 system. Note that tenant line 1 enters on pins
1 & 26 of the RJ-21X connector, and exits on pins 2 & 27 of the same connector. This also means a visitor would dial
a touch tone 1 to call the tenant connected to line 1. This scheme is used on all 12 lines on the RJ-21X connector,
occupying all pins up thorough the pin 24 & 49 pair, and repeats on up to the 96th tenant on the
8th module. The last pair on the RJ-21X connector (pins 25 & 50) has a special function. This
last pair is used (on the Master module only) as a connection for the Building Manager's
Programming Phone.
Module ID Module 1
Assignment "Master"
ON
DIP Switch
OFF
Settings
1 2 3
1
2
3
4
5
C.O.
6
Lines In
7
8
9
10
11
12
1
2
3
4
Lines Out
5
to
6
Apartment
7
Phones
8
(Dial Up
9
10
Codes)
11
12
Bldg Mgr Phn
2
n
n
Module 2 Module 3 Module 4
"Slave" "Slave" "Slave"
ON ON ON
OFF OFF OFF
1 2 3 1 2 3
13 25 37
14 26 38
15 27 39
16 28 40
17 29 41
18 30 42
19 31 43
20 32 44
21 33 45
22 34 46
23 35 47
24 36 48
13 25 37
14 26 38
15 27 39
16 28 40
17 29 41
18 30 42
19 31 43
20 32 44
21 33 45
22 34 46
23 35 47
24 36 48
n/a n/a n/a
Module 5 Module 6
"Slave" "Slave"
ON ON
OFF OFF
1 2 3 1 2 3 1 2 3
49 61
50 62
51 63
52 64
53 65
54 66
55 67
56 68
57 69
58 70
59 71
60 72
49 61
50 62
51 63
52 64
53 65
54 66
55 67
56 68
57 69
58 70
59 71
60 72
n/a n/a
Module 7 Module 8
"Slave" "Slave"
ON ON
OFF OFF
1 2 3 1 2 3
73 85 26 W/BL
74 86 28 W/G
75 87 30 W/S
76 88 32 R/O
77 89 34 R/BN
78 90 36 BK/BL
79 91 38 BK/G
40 BK/S
80 92
81 93 42 Y/O
82 94 44 Y/BN
83 95 46 V/BL
84 96 48 V/G
73 85 27 W/O
74 86 29 W/BN
75 87 31 R/BL
76 88 33 R/G
77 89 35 R/S
78 90 37 BK/O
79 91 39 BK/BN
80 92 41 Y/BL
43 Y/G
81 93
82 94 45 Y/S
83 95 47 V/O
84 96 49 V/BN
n/a n/a 50 V/S
VIKING
MODEL C-3000
©
VIKING
ELECTRONICS
HUDSON, WI 54016
12 UNIT APARTMENT
POWER
13.8 VAC
ENTRY CONTROLLER MODULE
POSTAL DOOR DOOR
STRIKE STRIKE
LOCK
1 2
INPUT
DIP
RJ21X
SWITCH
1 2 3 1 2 3 4 5 6 7 8 12 APARTMENT LINES IN/OUT
O
N
MULTI-MODULE
O
INTERCONNECTS
F
F
PWR
IN
USE
ENTRY ENTRY
PROGRAM PHONE PHONE 1 PHONE 2 OUT IN
RJ-21X
Tip
Ring
1 BL/W
3 G/W
5 S/W
7 O/R
9 BN/R
11 BL/BK
13 G/BK
15 S/BK
17 O/Y
19 BN/Y
21 BL/V
23 G/V
2 O/W
4 BN/W
6 BL/R
8 G/R
10 S/R
12 O/BK
14 BN/BK
16 BL/Y
18 G/Y
20 S/Y
22 O/V
24 BN/V
25 S/V