Viking BLK-3-EWP Technical Practice page 2

W a r r a n t y
W a r r a n t y
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Technical Support Department is available for assistance weekdays between 8 a.m. and 5 p.m. central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. The customer MUST have a complete description of the problem, with all
pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched
between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect
shipments cannot be accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a P.O. Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking's Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting, a Return Authorization (R.A.) number will be issued.
This number is valid for fourteen (14) calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the product over the counter at no charge. The
distributor will then return the product to Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed the steps listed in 1, 2 and 3, be aware that you will have to pay a
restocking charge.
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking dis-
tributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking
Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the pur-
chaser or others.
Vikings sole responsibility shall be to repair or replace (at Viking's option) the material within the terms stated above. VIKING SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND
INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESSED OR IMPLIED, OR FOR ANY
OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE, WHICH ARE HEREBY EXCLUDED BEYOND THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
I n s t a l l a t i o
I n s t a l l a t i o
* Gel−Filled Butt
120V AC
Connectors (included)
Note: Polarity Sensitive!
12V DC
adapter
(included)
(+) Red with
Black stripe
(+) Black
(−) Black with (−) Black with
White stripe White stripe
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone
line. It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800) 472-5555 or
!
Electronic Specialists Inc. at (800) 225-4876.
A. Installing the Strobe Light Using the Included Weatherproof Box
* Note: The gel-filled (water tight) butt con-
nectors are designed for insulation displace-
ment. Do not strip wires prior to terminating.
Blue Strobe
Light
n
n
LDB−3 Control Module
Red
11
Black
10
Orange
9
Purple
8
Yellow
7
Blue
6
Blue
5
Gray
4
Brown
3
Green w/ Yellow Stripe
2
Red w/ Yellow Stripe
1
* Note: The gel-
filled (water tight)
butt connectors are
designed for insula-
tion displacement.
Do not strip wires
prior to terminating.
(2) 10−32 x 3/8" self
tapping screws
Foam Strobe
Gasket Mounting Ring
WARRANTY
Switched 12VDC Output
(Strobe Light Power)
Normally Closed
Relay Contacts
Common
Normally Open
Disable/Info Switch Input
To Terminal Device/Phone
To C.O. Line or Analog
PABX/KSU Station
Preparing the Power Supply
Step 1. Cut off the barrel connector.
Step 2. Seperate wires
Step 3. Connect 12V adapter wires to power
supply wires on LDB-3 Control Module
using supplied Butt Connectors and
then plug in power supply
Nipple 1/2" x close
(2) 6−32 x 3/4" screws
7/8" Nylon
spacer
1/2" Close Nipple
Faceplate
2.75
1.05
4.60
4.0
4.4
2.50
Side View of the
Strobe Light (included)
Back view of weatherproof
single gang box (included)
Step 1. Step 2. Step 3.
IMPORTANT: Do NOT plug in the
adapter until after Step 3 is completed.
*
Gel−Filled Butt
Connectors (included)
Red
Red
Black
Black
Foam Weatherproof
Box
Gasket
0.6
1.50
2.84 2.0
Connect power supply
wires to LDB-3 module
power supply wires
(+) Black
(-) Black with
White Stripe
(2) Knockout
Plugs
LDB−3
Control Module