1. Manuals
  2. Brands
  3. Broadcast Tools Manuals
  4. Media Converter
  5. DTD-16 + G2
  6. Installation and operation manual

Broadcast Tools DTD-16 + G2 NET Installation And Operation Manual

16 channel dtmf tone/sequence decoder with ethernet inc
Hide thumbs Also See for DTD-16 + G2 NET:
Table of Contents

Advertisement

Quick Links

Download this manual
®
P R O B L E M   S O LV E D
Installation and Operation Manual
DTD-16 + G2 NET
16 Channel DTMF Tone/Sequence Decoder with Ethernet
Manual update: 6/12/2023
Firmware Version: 2.02
If you need a firmware upgrade, contact Broadcast Tools®
No part of this document may be reproduced or distributed without permission.
ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO
CHANGE WITHOUT NOTICE
NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.
Copyright® 1989 - 2023 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DTD-16 + G2 NET and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Broadcast Tools DTD-16 + G2 NET

Summary of Contents for Broadcast Tools DTD-16 + G2 NET

  • Page 1 NOTE: We recommend the use of Chrome, Firefox or Safari as your browser. Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.

  • Page 2: Table Of Contents

    DTD-16+ G2 Net Installation and Operation Manual Table of Contents Section Title Page # Introduction..........3 Safety Information .

  • Page 3: Introduction

    INTRODUCTION CAUTION! Thank you for your purchase of the DTD-16 + G2 NET DTMF Tone Decoder, which we will refer to throughout the manual as the DTD-16 + G2 NET. We are confident Broadcast Tools® this product will give you many years of dependable service. This manual is intend- Products, as with any ed to give you all the information needed to install and operate the Broadcast Tools®...

  • Page 4: Product Overview

    The package should contain the DTD-16 + G2 NET, a 9 VDC power supply, a USB-A/B cable, a “S9” RJ11-to-DB9 cable, a 7-foot BLUE straight-through CAT 5 cable, a 7-foot GRAY crossover CAT 5 cable.

  • Page 5: Installation/Operation

    NOTE: UPS Standby Power System We recommend that you connect your DTD-16 + G2 NET to a UPS standby power Never use any type of system. A UPS, like the BE600M1 from APC helps to minimize the risk to the DTD- power supply other 16 + G2 NET and provides power during a power outage.

  • Page 6: Led Indicators

    USB PGM Port additional information. This type B USB port is used to connect the DTD-16 + G2 NET to a computer for configuration via a virtual COM port. See the “Programming” section of this manual for more information.

  • Page 7: Relay Outputs

    DTD-16+ G2 Net Installation and Operation Manual Relay Outputs The eight relay outputs are SPST normally open/dry. Make your connections to the desired relays K1 A/B through K8 A/B. Front panel LEDs indicate when a relay is active. Open Collector Outputs The open collector outputs are labeled OC9 through OC16.

  • Page 8: Programming

    DTD-16+ G2 Net Installation and Operation Manual Programming The DTD can be programmed from a computer via its USB serial, RS-232 serial, or Ethernet interface. See the “Ethernet” section of the manual for Ethernet setup instructions. Connecting via the USB Serial “PGM” port: 1.

  • Page 10: Output Modes

    DTD-16+ G2 Net Installation and Operation Manual Output Modes Momentary If you have selected the momentary function for this output channel, you can program two codes up to 5 digits for the first code and 6 digits for the second code that can be used to activate that output.

  • Page 11: Dip-Switch Settings

    The default program values may be reloaded at any time by removing power from WEBSITE: the DTD-16 + G2 NET, holding down the PGM button and plugging in the power Visit our web site for and then releasing the PGM button after a few seconds. The PGM LED will blink product updates and once after the defaults are loaded.)

  • Page 12: Ethernet Setup And Operation

    TOOLS®. DOING SO DELETES ALL SOFTWARE AND VOIDS ALL WAR- useful to contact your RANTIES FROM BROADCAST TOOLS, INC. IT department, network administrator or net- Instructions for changing the IP address of the computer that will be used for the work consultant for configuration of this product are given here.
  • Page 13 DTD-16+ G2 Net Installation and Operation Manual Step 2: Under Advanced Network Settings click Change adapter settings. The Network Connections windows will pop up, as shown below. Step 3: Right click on the icon labeled Local Area Connection or Ethernet. A menu will appear.
  • Page 14 DTD-16+ G2 Net Installation and Operation Manual Step 4: On the Local Area Connection Properties page, double click on Internet Protocol (TCP/IPv4) to display properties. Step 5: Before making any changes to the network settings, write down the current WEBSITE: settings (or screen capture the page and print) so that they can be restored Visit our web site for once the unit is configured.

  • Page 16: Changing Network Settings

    DTD-16+ G2 Net Installation and Operation Manual 5. Click okay to connect to the DTD and type “p” into the terminal window and press return to enter programming mode. See: “Programming Steps” section of this manual. Changing network settings on the Ethernet “LAN/NET” port: WEBSITE: NOTE: We recommend the use of Chrome, Firefox, or Safari for as your browser.
  • Page 17 DTD-16+ G2 Net Installation and Operation Manual 5. To change the network settings, choose “Local IP Config” from the side bar: 6. The default work mode is TCP Server, TCP Client, UDP Server and UDP Client are also available. To change the TCP port choose “Serial Port” from the side bar and change the “Local Port Number”...

  • Page 18: Specifications

    DTD-16+ G2 Net Installation and Operation Manual Specifications Input Level: -20dBu to +24dBu. Input Impedance: 200K Ω balanced, 100K Ω unbalanced. Relay Outputs: Eight SPST, normally open dry contacts. 30 VDC @ 1 amp max. Open Collector Outputs: Eight, sinking up 6 VDC / 50 mA max to ground.

  • Page 19: Warranty

    If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in accordance with Broadcast Tools’...
  • Page 20 Product_Name Installation and Operation Manual DTD-16 + G2 NET Input OPTIONS LAN/NET OC11 OC13 OC15 AUD- AUD+ RS232 PWR 9-12VDC OC10 OC12 OC14 OC16 CGND APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
  • Page 21 Product_Name Installation and Operation Manual DTD-16 + G2 Net Component Layo T T o o ne Power RS-232 Audio Open Collector Relay Outputs 9-12VDC Port Serial Input Outputs 9-16 K1-K8 DTMF Tone Detection Jumper F = 50ms/50ms M = 100ms/100ms (default) S = 150ms/150ms JP1 –...

Table of Contents