Table of Contents
Advertisement
Quick Links
P R O B L E M S O LV E D
Installation and Operation Manual
16 channel DTMF Tone/Sequence Decoder Installation Manual
No part of this document may be reproduced or distributed without permission.
ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
tiny TOOLS™ is a trademark of Broadcast Tools, Inc.
All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.
Copyright® 1989 - 2013 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
DTD-16 Plus
Manual update: 06/24/2013
CHANGE WITHOUT NOTICE
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Broadcast Tools DTD-16 Plus
Summary of Contents for Broadcast Tools DTD-16 Plus
- Page 1 CHANGE WITHOUT NOTICE Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.
-
Page 2: Table Of Contents
DTD-16 Plus Installation and Operation Manual Table of Contents Section Title Page # Introduction ..........3 Safety Information . -
Page 3: Introduction
INTRODUCTION CAUTION! Thank you for your purchase of the 16 channel DTMF Tone/Sequence Decoder, which we will refer to throughout the manual as the DTD-16 Plus. We’re confident Broadcast Tools® this product will give you many years of dependable service. This manual is intend- Products, as with any ed to give you all the information needed to install and operate the product. -
Page 4: Product Overview
-20 to +24dbu. All connections are on removable screw terminals except for the USB Type B female port connector. The DTD-16 Plus may be set on a desktop, mounted on a wall or up to four units mounted on the RA-1, 1-RU mounting shelf. -
Page 5: Relay Connections
9600,8,N,1. Power Insert the power plug into the power jack on the DTD-16 Plus and the wall trans- former into the proper AC outlet. The power supply MUST be attached to the power jack to properly power the unit. Verify that the power LED is lit. -
Page 6: Programming
DTD-16 Plus Installation and Operation Manual PROGRAMMING To program the DTD-16 Plus, you must connect it to the USB port of a PC running a serial terminal program such as HyperTerminal, or PuTTY. When you first plug the DTD-16 Plus into your PC it should automatically install the correct FTDI USB Serial port drivers which will allow you to access the DTD on a COM port. - Page 7 DTD-16 Plus Installation and Operation Manual Momentary If you have selected the momentary function for this output channel, you can enter two codes up to 5 digits for the first code and 6 digits for the second code that can be used to activate that output.
-
Page 8: Specifications
DTD-16 Plus Installation and Operation Manual Specifications Input Level: -20dBu to +24dBu. Input Impedance: 200K Ω balanced, 100K Ω unbalanced. Relays: Eight SPST, normally open. 30Vdc@1 amp. Open Collectors: Eight, 12 Vdc / 50 ma. each USB Serial: 9600, 8,N,1 / USB type B female. -
Page 9: Warranty
If Broadcast Tools is notified of in writing of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned in to Broadcast Tools in accordance with Broadcast Tools’... - Page 10 DTD-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 11 DTD-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 12 DTD-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
-
Page 13: Product Label
DTD-16 Plus Installation and Operation Manual Product Label APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
Need help?
Do you have a question about the DTD-16 Plus and is the answer not in the manual?
Questions and answers