Table of Contents
Advertisement
Quick Links
P R O B L E M S O LV E D
Installation and Operation Manual
16 Channel DTMF Tone/Sequence Encoder
For firmware versions equal to or greater than: 2.01
No part of this document may be reproduced or distributed without permission.
ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
tiny TOOLS™ is a trademark of Broadcast Tools, Inc.
All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.
Copyright® 1989 - 2013 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
DTE-16 Plus
Manual update: 06/24/2013
CHANGE WITHOUT NOTICE
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Broadcast Tools DTE-16 Plus
Summary of Contents for Broadcast Tools DTE-16 Plus
- Page 1 CHANGE WITHOUT NOTICE Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.
-
Page 2: Table Of Contents
DTE-16 Plus Installation and Operation Manual Table of Contents Section Title Page # Introduction ..........3 Safety Information . -
Page 3: Introduction
DTE-16 Plus Installation and Operation Manual INTRODUCTION CAUTION! Thank you for your purchase of a DTE-16 Plus is a web enabled transparent three input, single output stereo switcher/router (referred to as the DTE-16 Plus Broadcast Tools® throughout this manual). We’re confident that this product will give you many years Products, as with any of dependable service. -
Page 4: Product Overview
The package should contain the DTE-16 Plus, a 7.5 to 12 VDC wall transformer and a USB A/B cable. Manuals may be downloaded from our web site. Installation The DTE-16 Plus interfaces to external equipment through removable euroblock screw terminals. -
Page 5: Surge Protection
HYPERLINK "http://www.polyphaser.com" www.polyphaser.com and HYPERLINK "http://www.itwlinx.com" www.itwlinx.com. UPS Standby Power System We recommend that you connect your DTE-16 Plus to a UPS system. A UPS helps minimize the risk to the DTE-16 Plus and provides power during a power outage. Channel Control Inputs Connect a normally open dry contact closure between the “GND”... -
Page 6: Programming
DTE-16 Plus Installation and Operation Manual Programming To program the DTE-16 Plus, you must connect it to the USB port of a PC running a serial terminal program such as HyperTerminal, or PuTTY. When you first plug the DTE-16 Plus into your PC it should automatically install the correct FTDI USB Serial port drivers which will allow you to access the DTE on a COM port. -
Page 7: Function Modes
DTE-16 Plus Installation and Operation Manual Function Modes There are four DTMF transmit modes selectable via the four-position DIP-switch package on the DTE’s printed circuit board. These modes control the tone duration and spacing when triggered from the channel control inputs. -
Page 8: Operation
The “DV” LED will light to indicate valid tone generation. Computer Control Command Syntax To control the DTE-16 Plus from a computer, it must be connected to the USB port on a PC running a serial terminal program such as HyperTerminal, or PuTTY. When you first plug the DTE in to your PC it should automatically install the correct FTDI USB Serial port drivers which will allow you to access the DTE on a COM port. -
Page 9: Specifications
DTE-16 Plus Installation and Operation Manual Specifications Mix Input Level: Nominal program audio level. NOTE: Expect a mixing loss thru the mix network. Mix Input Impedance: 100 ohms balanced. Output/Tone Audio Level: 0 dBu nominal, +4dBu max, @ 100 ohms, balanced. -
Page 10: Warranty
If Broadcast Tools is notified of in writing of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned in to Broadcast Tools in accordance with Broadcast Tools’... - Page 11 DTE-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 12 DTE-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 13 DTE-16 Plus Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
Need help?
Do you have a question about the DTE-16 Plus and is the answer not in the manual?
Questions and answers