Advanced Option Menu - Acer DV420 User Manual

SCREEN SAVER
COOLING FAN
BRIGHTNESS
MOTION
:SEL +-:ADJ
EXIT
• {COOLING FAN} - Select {ON} to turn on the cooling fan
all the time. Select {AUTO} to turn on/off the cooling fan
according to the display's temperature.
NOTES:
• The default {AUTO} option will start running the cooling
fan if the temperature of 65°C (152°F) is reached, and
will keep running for 30 minutes after cooling down to the
temperature of 62°C (144°F).
• A temperature-warning message will be shown on the
screen once the temperature reaches 79°C. All key
function except [Power] key will then be disabled.
• {BRIGHTNESS} - Select {ON} and the brightness of
the image will be reduced to an appropriate level, and
the Brightness setting in the Picture menu will become
unavailable.
• {MOTION} - Select the time interval ({10 ~ 900} Seconds /
{OFF}) for the display to slightly expand the image size and
shift the position of pixels in four directions (up, down, left, or
right).
SIDE BORDER COLOR
Adjust the brightness of the black areas displayed on both sides
of 4:3 images.
CONFIGURATION3 RESET
Reset all settings in the CONFIGURATION3 menu to factory
preset values.

4.2.8. ADVANCED OPTION menu

ADVANCED OPTION
INPUT CHANGE
TERMINAL SETTING
SCAN CONVERSION
COLOR SYSTEM
SCAN MODE
SERIAL CONTROL
PIP
APM
1
LAN SETTING
ADVANCED OPTION RESET
2
FACTORY RESET
3
:SEL :NEXT
SET
INPUT CHANGE
Select the time for input switching as {NORMAL} or {QUICK}.
NOTE: The selection {QUICK} may cause a slight noise.
AUTO
OFF
OFF
:RETURN :EXIT MENU
MENU
NORMAL
LAN
OFF
:RETURN :EXIT MENU
EXIT MENU
TERMINAL SETTING
Select the mode to display the HDMI or DVI signal according to
their signal format depending on their source device.
• {DVI MODE}: Used for DVI-D signal.
• Select {DVI-PC} when the source device is a PC.
• Select {DVI-HD} when the source device is a video
device.
• {HDMI SIGNAL}: Used for HDMI signal.
• Select {LIMITED} when displaying the signal that uses
16 to 235 levels of 256 levels for each R, G, and B.
• Select {FULL} when displaying the signal that uses all
256 levels (from level 0 to 255).
TERMINAL SETTING
DVI-MODE
HDMI SIGNAL
PIP
1
2
3
:SEL +-:ADJ
SCAN CONVERSION
Choose to enable or disable the IP (Interlace to Progressive)
conversion function.
• {PROGRESSIVE} - Enable the IP conversion function
(recommended). Once enabled, the interlace input signal will
be converted to progressive format for better display quality.
• {INTERLACE} - Disable the IP function. This mode is
suitable for displaying motion pictures, but it increases the
chance of image retention.
COLOR SYSTEM
Selects the Color System depends on your input video format.
The options are: {AUTO} / {NTSC} / {PAL} / {SECAM} /
{4.43NTSC} / {PAL-60}.
NOTE: This item is functional for VIDEO input only.
SCAN MODE
Change the display area of the image.
• {OVERSCAN} - Display about 95% of the original size of the
image. The rest of the areas surrounding the image will be
cut off.
• {UNDERSCAN} - Display the image in its original size.
NOTE: This item is functional for HDMI-Video timing input
only.
SERIAL CONTROL
Select the network control port.
The options are: {RS-232C} / {LAN}.
NOTE: If {LAN} is selected, then {RS-232C} will not be
activated, even if a cable is attached, and vice versa.
DV420 /DV460 /DV550
DVI-PC
FULL
:RETURN :EXIT MENU
EXIT MENU
19