Related Manuals for cetis ND2100IP
Summary of Contents for cetis ND2100IP
- Page 1 ND2100IP VoIP Phone | User Manual ND2100IP VoIP Phone | Users Manual www.CetisGroup.com www.CetisGroup.com...
-
Page 2: Table Of Contents
1.1 Overview of Hardware ---------------------------------------------------------------------------------------------------------- 2 1.1.1 ---------------------------------------------------------------------------------------------------------------------------------------------------- 2 1.1.2 ---------------------------------------------------------------------------------------------------------------------------------------------------- 2 1.2 Overview of Software ----------------------------------------------------------------------------------------------------------- 3 2. Handset keys for ND2100IP ---------------------------------------------------------------------------- 4 2.1 Function table of keystroke -------------------------------------------------------------------------------------------------- 4 2.1.1 Store numbers: ----------------------------------------------------------------------------------------------------------------------------- 4 ... - Page 3 ND2100IP VoIP Phone | User Manual Reference – Quick Keys ---------------------------------------------------------------------------------- 18 Reference – SIP Quick Start to Register a Single Phone -------------------------------------- 19 Program your connection under the VoIP -> SIP Configuration Screen ------------------------------------------------------------- 19 ...
-
Page 4: Function
• Introduction • This is the user manual for the ND2100IP. Some configuration is necessary before using the ND2100IP phone. • This manual will illustrate how to set up the phone through keyboard and web User Interface (UI). 1.1 Overview of Hardware 1.1.1... -
Page 5: Overview Of Software
ND2100IP VoIP Phone | User Manual 1.2 Overview of Software Network Protocol SIP v1(RFC2543) • TFTP Client/DHCP Client/PPPOE Client • V2(RFC3261) • Telnet/HTTP Server • IP/TCP/UDP/RTP/RTCP • DNS Clients • IP/ICMP/ARP/RARP/SNTP • Codec G.711： 64K bit/s(PCM) • G.729A： 8k bit/s(CS-ACELP) •... -
Page 6: Handset Keys For Nd2100Ip
2.1.6 Speed Dial Keys Mute Press Mute voicepath The ND2100IP is configured with either 5 (MWD5) or MWI - Flashing or Message Waiting TouchLite Indication and Speed 10 (MWD) speed dial keys, programmable through the Dial web UI under Advanced ->... -
Page 7: Current State
(This setting won’t take effect unless you save the config and reboot the device) - Enable Static; - Set ND2100IP’s IP address in the IP Address; - Set netmask in the Netmask field; - Set router IP address in the Gateway;... -
Page 8: Voip
Setting page of public SIP server: register expire time, default is 60 Register Expire Time: seconds. ND2100IP will auto configure this expire time to the server recommended setting if it is different from the SIP server. Please refer to Value_add_service for detail. -
Page 9: Advance
Click Add to add new port mapping item and Delete to delete current port mapping item. Lease table name. Lease Table Name: Start IP of lease table. Start IP: End IP of lease table. Network device End IP: connecting to the ND2100IP LAN port can dynamic www.CetisGroup.com... -
Page 10: Stun
Access list support two type limits: input_access limit or output_access limit. Each type supports 10 items maximum. ND2100IP firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address. www.CetisGroup.com... -
Page 11: Vlan Configuration
TCP/IP/ Protocol Type: moment, the DSCP of SIP signals which between ICMP/UDP. ND2100IP Phone and MGC. It will use Class Selector 5 (The value is 0xA0). And the DSCP of mediums port range if this rule Port Range: information (In RTP packets) would be used the values of DiffServ Value field. -
Page 12: Memory Key Programming
ND2100IP VoIP Phone | User Manual the time from 0~9 second, it is necessary. Tn must be different from ND2100IP’s phone number. the last two digits in the entry. If Tn is not included in no answer call forward time setting. -
Page 13: Call Park And Retrieve
3.5.10 MMI Filter “silently” to extension 1107. ‘Silent’ means the user will not hear the DTMF tones. MMI filter is used to make access limit to ND2100IP In Memory 3, the transfer to 1107 will occur, after the phone. connection is established, a pause will happen then When MMI filter is enable. -
Page 14: Dial-Peer Dial Rule Setting
ND2100IP VoIP Phone | User Manual register to the port of VPN server VPN Server Port: the group ID of UDP VPN Server Group ID: : the area code VPN server L2TP Server Area Code register to the address of VPN server... -
Page 15: Auto Update
<<VOIP CONFIG FILE>>Version: 1.0007 Config file import: import the config file <GLOBLE CONFIG MODULE> ConfFile Version：7 ND2100IP phone support FTP and TFTP auto update, the gateway will auto obtain the configure file from your update server if configured. To obtain the original configure file, you can use the FTP/TFTP back up as describe above. -
Page 16: Phone Book
ND2100IP VoIP Phone | User Manual set the MGR log level MGR Log Level: set the SIP log level SIP Log Level: set the IAX2 log level IAX2 Log Level: Please click “apply” after setting 3.9.5 MMI SET Set the greeting information on LCD. -
Page 17: Set The Phone Being Connected To Server
Register address of public SIP Register Server Addr: server - choose static; - fill in the IP address of ND2100IP in the IP Register port of public SIP server. Register Server Port: address; default port is 5060 - fill in the subnet mask in Netmask;... -
Page 18: Iax Setting
4.3 How to use the dial rule? ND2100IP provide flexible dial rule, with different dial- rule configure, user can easily implement the following function: - Replace, delete or add prefix of the dial number. - Page 19 ND2100IP VoIP Phone | User Manual If the call starts with 2, the first 2 will be deleted, 2T rule: and the rest number will be sent to private SIP server. If the call starts with 3, the first 3 will be deleted, 3T rule: and the rest number with be sent to public SIP server.
-
Page 20: Reference - Quick Keys
#. If the password (in the existing config on the phone is 123, and the new config file is 1234.ND2100IP.txt), then the user would enter **77*123*1234#. The user should NOT be prompted for the password. The phone will then download the new config file 1234.ND2100IP.txt. -
Page 21: Reference - Sip Quick Start To Register A Single Phone
Reference – SIP Quick Start to Register a Single Phone The Cetis, Inc SIP sets are SIP-only endpoints powered only by POE/802.3af and will acquire an IP address when met by a DHCP server. Begin by plugging your POE Ethernet cable into the WAN port. -
Page 22: Speed Dial And Touchlite Message Keys Are Programmed Under Advance -> Memory Key
In this example, it is programmed to dial number (7001) on the IP/PBX for retrieving voicemail messages. Manual Programming - Programming the ND2100IP via the LCD and Submerged Keys There are 2 submerged keys (above the 10 speed dial keys/underneath the faceplate). The left (store) key is used to store speed dials as well as enter the internal menu to check status and program the phone.