General; Step:2 S Hookup Ic. Ccesccsccssetesdescacesnseoscosecacessonsetesecneossconsteeses - Sony KP-46C36 Service Manual

Step 2: Hookup
Although you can use either an indoor or outdoor
antenna with your projection TV, we recommend that
you connect an outdoor antenna or a cable TV system
to get better picture quality.
SLR ESB Mi AE TS GTI LEE EI AIEEE SLES
Connecting an antenna
Connect your antenna cable to the VHF/UHF antenna
terminal. If you cannot connect your antenna cable
directly to the terminal, follow one of the instructions
below depending on your cable type.
(Rear of projection TV)
* VHF only
__75-ohm coaxial cable
VHF/UHF
or
© VHF/UHF
lg)
or
* Cable
(Rear of projection TV)
© VHF only
_300-ohm twin lead cable
VHF/UHF
or
r
© UHF only
or
© VHF/UHF Antenna connector
c 75-ohm coaxial cable
"we 6 Ps
and
EAC-66 U/V mixer
t {not supplied)
uO == all
300-ohm twin lead cable
Notes
© Most VHF/UHF combination antennas have a signal splitter.
Remove the splitter before attaching the appropriate connector.
¢ Ifyou use the U/V mixer, snow and noise may appear in the
picture when viewing cable TV channels over 37.
G6-EN Getting Started
SECTION 1
GENERAL
Connecting an antenna/cable TV
system without a VCR
To cable or antenna
(Rear of projection TV)
VHF/UHF
—<)
Cable
To cable box
If your cable company requires you to connect a cable
box, make the connection as follows:
(Rear of projection TV)
VHF/UHF
Cable | 3
IN out
Cable box
To cable box and cable
{Rear of projection TV)
AUX
Cp
T
CONVERTER
Le
75-ohm coaxial
cable (not supplied)
CATV cable VHF/UHF
————=p—«p)
Pay cable TV systems use scrambled or encoded signals
requiring a cable box* in addition to the normal cable
connection.
* The cable box will be supplied by the cable company.
Note
* You cannot watch the signal through an AUX connector as a
window picture.
To cable and antenna
{Rear of projection TV)
CATV cable AUX
To
CONVERTER
Antenna cable VHF/UHF
EL)
Note
© Do not connect anything to the TO CONVERTER connector in
this case.
The operating instructions mentioned here are partial abstracts from
the Operating Instruction Manual. The page numbers of the
Operating Instruction Manual remain as in the manual.
Connecting an antenna/cable TV system with a VCR
For details on connection, see your VCR instruction
manual.
Before making the connection, disconnect the AC power
cords of the equipment to be connected.
To a conventional VCR
Notes
For models KP-46C36, you can connect the audio and
video outputs of the VCR to VIDEO 3 IN jacks instead of the
VIDEO 2 IN jacks.
* To connect a monaural VCR, connect the audio output of the VCR
to AUDIO-L (MONO) of VIDEO 1/2/3 IN on the projection TV.
Without a cable box
(Rear of projection TV)
AUDIO-R (red)
With a cable box
(Rear of projection TV)
AUDIO-L (white)
AUDIO-R (red)
VMC-810S/820S
(not supplied)
VMC-810S/820S
(not supplied)
After making these connections, you will be able to do
the following:
* View the playback of video tapes
¢ Record one TV program while viewing another
program
¢ Watch two TV programs at once using PIP
VHF/UHF
Antenna cable
i VHF/UHF
VCR output
Antenna cable
VHF/UHF
input
Video and audio
outputs
Antenna cable
AUgIO vipEO = OUT
slg 9 9l
audio TIVHF/UHF
ts
VHF/UHF
Cable box output Antenna
cable
ene je coe
Splitter (not supplied)
Getting Started
7-EN