Advertisement
Operation
• Base Operation
Remote controller
1. Unit start
Press ON/OFF
on the
emote controller,
unit starts.
「
2. Select operation mode
COOL button:Cooling mode
FAN button: Faning mode
DRY button: Dehumidify mode
3.Select temp.setting
Press TEMP&/ TEMP
....
button
TEMP •Every time the button is pressed, temp.setting
increase 1
C,if kept depressed, it will increase
°
rapidly
TEMP...,.
Every time the button is pressed, temp.setting
dec
ease 1
C,if kept depressed, it will
°
decrease rapidly
「
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed
changes as follows:
Remote controlle
「:
....... .. 丑
�W
MED
Air conditioner is running under displayed fan speed.
When FAN is set te AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Remote
Operation
Mode
Controller
In COOL mode, the AC unit will emit air
Cool acco
temperature display
COOL
口
The unit will return to ambient temperature after
a moment ago
m
In
than temp.setbng+2'C, urntw,11 run 1nterm1ttently at LOW
DRY
DRY
speed regardless of FAN setting
In FAN operation mode, the unit will not operate in COOL or
HEAT mode but onty in FAN mode, AUTO is not available in
曰
FAN
FAN mode And temp. setting is disabled In FAN mode,
sleep operation is not available
已匕
m:) (:iJ l§)
0
0
0
D isplay
1111---. .
言勹
HI
Cl
Note
ding to the remote setting on the
「
mode, when room tempe
atu
e becomes lower
「
「
• Emergency operation and test operation
Emergency Ope
ation:
「
• Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditone
can run automatically for a while.
• When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
• When power switch is turning on for the first time and
三 了
emergency operation starts, the unit will run au t omatically in
the follo w ing modes:
• It is impossible to change the settings of temp. and fan speed.It
is also not possible to operate in timer or dry mode.
Test operation:
Test operation switch is the same as emergency switch.
• Use this switch in the test operation when the room
temperature is below 16
C, do not use it in the
°
nom面operation.
• Continue to press the test ope
switch fo
mo
e than 5 seconds . Afte
you hea
he "Pi" sound twice, release
「
「
your finger from the switch: the cooling
门
operation starts with the air flow speed "Hi".
• Under this operation mode.the fan motor of indoor
unit will run in high speed.
• Air Flow Direction Adjustment
1.Status display of air flow
Vertical flap
r:-
Pos.1 尸 尸寸
....
:::-
Initial state
Pos.2 No initial state disaplayed on remote controller, the
vertical flap will be fixed on the current position
2.Left and right air flow adjustment
For each press of sw1 NG <Jt>button, remote controller
displays as follows :
remote controller:
Pos.1 气月 Pos. 2严Pos.3严司Pos.4严
Pos.5� 同 Pos.6 亨
Note: In some model: The remote has the button SWI NG 伞But the
AC doesn't have the left and
in this condition, change the direction of vertical blades manually.
Cautions:
• When adjusting the flap by hand,turn off the unit.
• When hum心ty is high,condensate water might occur
at air outlet if all vertical louvers are adjust to left or right.
•
It is advisable not to keep horizontal flap at downward
position for a long time in COOL or DRY mode ,
gtherwise, condensate water might occur.
Pi
ation
「
「
寸产厂寸- 酝 7 (Au to swin g)
看
、
ight air flow auto adjustment function.
「
「
2
Advertisement
