Related Manuals for Sumake HT-6750
Summary of Contents for Sumake HT-6750
- Page 1 INSTRUCTION MANUAL HT-6750 ITEM NO.: HYDRAULIC HAND RIVETER KIT HT-6850M ITEM NO.: HYDRAULIC HAND RIVETING NUT TOOL KIT HT-6750 HT-6850M HT-6750(6850M)-I-1403A-C1...
- Page 4 RIVETER IS DESIGNED FOR INTERMITTENT DUTY AND MAINTENANCE WORK ONLY, Manual Hydraulic Riveter The HT-6750 is a hydraulic tool designed to set from 1/8 inch up to and including 1/4 inch diameter steel, stainless steel, aluminum and plastic rivets by changing only the nose piece.
-
Page 5: Nose Piece Installation
OPERATING INSTRUCTIONS The HT-6750 hydraulic riveter installs fasteners by a pull and release system. Pumping the handles (see fig. 2 on the next page) will actuate the tool. The tool must be actuated when installing fasteners or changing nose pieces. After installing the fastener or changing the nose piece, the tool must be returned to its original position. - Page 6 Figure 2 Rivet Pintail Removal: Once Rivet is installed pintail must be removed Point tool downward 2. Squeeze the HANDLES while pressing the RELEASING BUTTON It is necessary to REMOVE PINTAIL BEFORE ATTEMPTING TO INSTALL ANOTHER RIVET Figure 3...
- Page 7 Three Piece Jaw Installation and The jaws are installed at the factory and should only need to be removed for periodic inspection and cleaning. To remove the jaws unscrew the NOSE TUBE from the tool in a counterclockwise direction. THREE PIECE JAW SYSTEM Remove the JAW HOLDER by unscrewing it in a counterclockwise direction.
- Page 8 When jaws are in place, insert jaw holder into spring, being sure to keep large end of jaw holder pointing downward. THREE JAW SYSTEM Hold tool with the PULLER SHAFT pointing down and the JAW PUSHER fully extended. Screw the jaw holder on to the PULLER SHAFT. HAND TIGHTEN ONLY.
-
Page 10: Troubleshooting
TROUBLESHOOTING Problem Solution First Step: Lightly tap nose against a hard surface while after breaking squeezing HANDLES and pressing down the RELEASING BUTTON with tool pointing downward Pintail should then fall out, see fig. 4. (If that does not 1 . Rivet pintail is stuck in tool work try Second Step) Second Step: (Use this only if first step does not work) Remove NOSE TUBE and JAW HOLDER (for help see... -
Page 11: Optional Accessories
OPTIONAL ACCESSORIES Part Number Description Nose Piece - 1/8" for Trim Molding Pop Rivets Nose Piece - 1/8" Stand Off Pop Rivets Nose Piece - 1/4" Monobolts Nose Piece - Spec. GM Glass Stop Travel, Pop SERVICE NOTES: C O N V E RT I N G A R I V E T E R T O A N U T S E T T E R can be converted from a riveter to a nutsetter by changing several of the nose... - Page 12 NUTSETTER sets 3mm Nutsetter through 3/8-24 threaded aluminum inserts and up to 1/4-20 steel inserts. Size changes accomplished changing PULL-UP STUD and ANVIL. No tools required. Installing threaded Inserts: 1. Make sure proper PULL-UP STUD and are ANVIL in place. 2.
- Page 13 No load: 65.8 dB(A) 80 dB(A) due Traction Power 3500 lbs (1600 kg) to risk of impaired Uncertainty Uncertainty hearing! ² Net Weight 1.92 lbs (0.87 kg) K= 1.5 m/s K= 3dB SUMAKE INDUSTRIAL CO., LTD 4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91 HT-6750-S-1403A-C1F...
- Page 14 3500 lbs (1600 kg) No load: 65.58 dB(A) 80 dB(A) due to risk of impaired Uncertainty Uncertainty Net Weight 1.92 lbs (0.87 kg) hearing! ² K= 1.5 m/s K= 3dB SUMAKE INDUSTRIAL CO., LTD 4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91 HT-6850M-S-1403A-C1F...
-
Page 15: Ec Declaration Of Conformity
DECLARATION OF CONFORMITY SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment：HYDRAULIC HAND RIVETER Model/ Serial No.：HT-6750 to which this declaration applies, complies with these normative documents: ... - Page 16 DECLARATION OF CONFORMITY SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： HYDRAULIC HAND RIVETING NUT TOOL Model/ Serial No.：HT-6850M to which this declaration applies, complies with these normative documents: ...
- Page 17 HT-6750 HYDRAULIC HAND RIVETER KIT PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty HT6750-01 Hydraulic Housing 25-1 HT6750-25-1 Lever Right Skin HT6750-02 Hydraulic Piston HT6750-27 Guide Sleeve HT6750-02-1 O-Ring 29-1 HT6750-29-1 Guide HT6750-02-2 Wear-Ring 29-2 HT6750-29-2 HT6750-03 Front Sleeve...
- Page 18 HT-6850M HYDRAULIC HAND RIVETING NUT TOOL KIT PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty HT6850M-01 Hydraulic Housing HT6850M-33D Nose Piece M6 HT6850M-02 Hydraulic Piston HT6850M-33E Nose Piece M8 HT6850M-02-1 O-Ring HT6850M-34A Mandrel M3 HT6850M-02-2 Wear-Ring HT6850M-34B Mandrel M4 HT6850M-03 Front Sleeve HT6850M-34C...
- Page 19 NOTE www.SUMAKE.com www.AIRCOMPRESSOR.com.tw...
- Page 20 NOTE www.SUMAKE.com www.AIRCOMPRESSOR.com.tw...
Need help?
Do you have a question about the HT-6750 and is the answer not in the manual?
Questions and answers