ATS are divided to basic and intelligent two types, user can upgrade the basic ATS to an intelligent one easily by inserting a hot-swappable Network Management Card, which enable user to monitor and manage the ATS with web interface or SNMP platform. II Function Description 1.
ATS User Manual Buzzer switch setting; III Application 1. ATS products are applicable for all kinds of server racks and network cabinets. 2. ATS products are in accordance with the regulation of RoHS. IV Product Schematic...
The corresponding indicator will always light on if a choice was made. If not, the two indicators will stay the off status. Please be noted that the intelligent ATS has the Lock function, if user can not do the setting above, it is probably because the controller panel is locked in the firmware and please log on to the Web interface to unlock.
The P6 and P9 shown above display is to restore factory operation Note: The operation of restoring factory settings does not affect the output and power supply of the ATS, but the network configuration and device IP are restored to the system default configuration. Serial connection Use the supplied serial cable, insert the RJ45 connector to RS232 communication port and connect the other end to the serial port of local PC or serial server.
Page 9
ATS User Manual 9.4. Insert the RJ45 connector of the supplied serial cable into the RS232 port of the ATS front panel, connect the other end to the port COM1 of local PC 9.5. Select the serial port from this column...
ATS User Manual perform normal communication after successful software update. VII Hyper Terminal user guide 1. Use the supplied serial cable, connect one end to the RS232 port and the other end to serial port of local PC. Running the Hyper terminal program (like Windows Hyper terminal), Here we take the Windows Hyper Terminal for example.
Page 11
5. Enter a Name like ATS and click OK 6. Select the COM port that is occupied and click OK 7. Set the baud rate of ATS as 19200 and enter configuration information for data bits, parity and flow control as provided below, then click OK...
Page 12
ATS User Manual 8. If it is not the first time that the PC runs the Hyper Terminal, it will goes directly to the window as the 4th item of this chapter, then follow up the instruction from the 4th to 7th and enter the Hyper Terminal monitoring interface as below: 10.
Page 13
ATS User Manual 10.2. Click on ASCII Setup, pop-up window as below: 10.3. Tick off the boxes as window above, then click the OK button and return to the monitoring interface...
Page 14
11.Press Enter, following message will be displayed in the interface if setting success. Main Menu 1-Device Manager 2-Set Current And Voltage Limit 3-System Time 12. View the ATS status Type 1 and press Enter, the ATS status will be displayed in the interface as below:...
Page 15
Source A Voltage: The voltage of the source A Source B Voltage: The voltage of the source B Output Current : The output current of the ATS Selected Source: The current input power is source B Preferred Source: The preferred input power is source A...
Page 16
(Set Switchover Time) enter the value preferred then press Enter. The reverse-switch time ranges from 10 to 60 seconds. The ATS will transfer to the preferred input power after defined time when user give the order to transfer or the preferred input line recover from power failure 15.
Page 17
Enter to enter the interface as below: Enter the value you want to set, then press Enter. Return to Set Current and Voltage Limit interface, user can view the re-defined value. 16. Setup the system time of ATS; the path is: Main Menu=>3( System Time)...
Page 18
ATS User Manual 16.1. Select 1 to modify date; the path is: Main Menu=>3( System Time)=》1 Enter the correct date format in the window. For instance 2010/07/22 The above window shows that the setting is successful. 16.2. Timing re-defining, the path is Main Menu=>3( System Time)=>2...
HTTPS and SNMP protocol and helps to monitor the total load current; input/output voltage of the ATS timely so that the user can manually or automatically switch the input power between source A and source B to ensure uninterrupted power supply of the critical IT equipments. When abnormality detected, the software will send E-mail/TRAP message to administrator.
Click the "Network Config" on the navigation bar to change the IP of the ATS, see the below interface, change the IP address of the ATS and make sure it is in the same segment as the PC; ...
ATS User Manual Access method Connect the device to LAN or WAN, user can access and manage the device through Web or SNMP, please see detail information as below. 3.1 Web Device supports HTTPs protocol, we recommend user to access through IE10 IE 11 or newer version and Google chrome, the Web access method are as below: ...
Device Status interface shows the status of the power input as well as the current & voltage status of the Device. The “Operating Status” section shows the current operating status of ATS: Green means OK; Red means abnormality or power failure The Input section shows the voltage of source A and Source B, when voltage abnormality detected, the value of the voltage displayed in the interface will turn to red.
ATS User Manual 3.1.2 Device Config Device Config shows the preferred power source, reverse-switch time, buzzer mute, hardware lock and source name. Figure 2 Device Config Priority Setting: To Select preferred power source from the drop-down list of main Input;...
ATS User Manual Figure 3 Threshold interface The default acceptable current range is between 0A to 32A, If the current is not within this range, device will alarm. The default acceptable voltage range is between 180V to 260V, If the voltage is not within this range, device will alarm.
Page 25
ATS User Manual Figure 4 Events logs interface (1) Click the "calibration" button to calibrate the equipment time. After calibration, the equipment time is consistent with the PC time; (2) Select the "Alarm Log" item in the "Log Type" drop-down menu to view the alarm log information.
ATS User Manual page: 3. Click on the browser menu "Tools" -> click on "Internet Options" -> click on the "Security" tab -> click on the "Custom Level" button -> initialize the "right" as ActiveX controls marked as safe to execute scripts and "Execute script"...
ATS User Manual maximum length is limited to 10 characters. The password complexity requires both uppercase letters, lowercase letters and numbers, no special characters, and a length limit of 6-15 characters. 3.1.6 Network Config To configure the network such as IPv4 address, subnet mask, default gateway, DNS.
Page 28
ATS User Manual voltage threshold is exceeded or ATS failure occur, the alarm information will be notified to the administrator by email. Figure 7 HTTP/SMTP config a. HTTP settings (1) Supports custom HTTPS port b. SMTP settings (1) Select disable and enable to disable and enable the SMTP service...
ATS User Manual 3.1.8 SNMP/Telnet The interface configures the SNMP / telnet access mode of the device, which can set the set/get community name and tarp of SNMP, and the security level, account number, password and key of SNMPv3. There are also enable and disable operations for telnet service. The specific operation is as...
(4) "Restore to factory Settings" is to restore to default configuration when ATS was built in the factory. Note: Make sure there is no power failure, no internet disconnection, and no operation on the web interface during restart, If the device is directly connected to PC, the local connection will disconnected and connected automatically.
Page 31
Buzzer switch and status 1.3.6.1.4.1.30966.10.1.1.18 keyLock Panel key lock status 1.3.6.1.4.1.30966.10.1.1.19 deviceName Device name 1.3.6.1.4.1.30966.10.1.1.20 Figure 2-1 ATS MIB Description information table Note: Considering the decimal value of load is not allowed when the load current of both power source,...
[1] outputCur.0 (Integer): 0 [2] snmpTrapEnterprise.0 (Object ID): ats Telnet access The application of Telnet enables the user to remotely manage the ATS easily. The user can monitor and manage the device by entry the command line from the Telnet program. Telnet requires the customer terminal from the PC and there is free software like PUTTY available.
ATS User Manual and maximum thresholds for voltage, and minimum and maximum thresholds for current C. " reboot " command Entry reboot command line to restart the device. D. " reset " command Entry reset command line to restore to factory settings.
Display resolution 100mA ±1%+1D Digital display LED tube, three digit, red Display Output voltage Display resolution ±1%+3D IP address Left circulation display(intelligent ATS) Mounting method Horizontal rack mount Occupy 1U or 2 U Case colour colour black Working 0~45℃ temperature Storage -20~70℃...
Need help?
Do you have a question about the ATS and is the answer not in the manual?
Questions and answers