Table of Contents
Advertisement
CD Player
The CD will! not play.
> The CD is dirty.
> The CD is inserted label side down.
> Moisture condensation has built up.
Leave the system turned on for
about an hour until the moisture
evaporates,
Play does not start from the first
track.
> The player is in program or shuffle
mode. Press CONTINUE.
General
There is no sound.
> Rotate VOLUME clockwise.
> The headphones are connected.
Disconnect them.
Sound comes from one channel, or
unbalanced left and right volume.
> Check the speaker connections of
the inoperative channel.
The left and right sound is reversed.
> Check the speaker connection and
speaker placement.
Bass is lacking or the location of the
musical instruments is apparently
imprecise.
> Check the speaker connections for
proper phasing.
f
There is severe hum or noise.
> The TV or VCR is too close to the
stereo system. Move the stereo
system away from the TV or VCR.
"12:00 AM" flashes in the display.
> A power interruption occurred.
Set the clock and preset radio
stations again.
The remote does not function.
> The batteries have run down.
Replace both batteries.
> There is an obstacle between the
remote and the system. Remove the
obstacle.
eS
Maintenance
To clean the tape heads and tape
path
Contaminated tape heads cause poor
recording or sound drop-out in playback.
We recommend cleaning after every 10
hours of operation.
Open the cassette holder and wipe the
heads, the pinch rollers and the capstans
with a cleaning swab slightly moistened
with cleaning fluid or alcohol. Wipe the
parts shown below:
Deck A
Cleaning swab
Capstan
Playback head
Ə
Pinch roller
Deck B
Cleaning swab
Capstan
Record/playback
head
Q
|
Erase head
Pinch roller
Insert atape after the areas cleaned are
completely dry
To demagnetize the tape heads
After 20 to 30 hours of use, enough residual
magnetism will have built up on the heads
to begin to cause loss of high frequencies
and hiss. At this time, demagnetize the
heads and all metal parts in the tape path
with a commercially available tape head
demagnetizer. Refer to the instructions of
the demagnetizer.
To clean the cabinet
Use a soft cloth slightly moistened with a
mild detergent solution.
To clean the CD
When a CD is dirty, clean it with a cleaning
cloth. Wipe the CD from the center out.
Notes on CDs
e Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static spray intended for vinyl LPs.
e If there is a scratch, dirt or fingerprints on
the CD, it may cause a tracking error.
fg
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND
TOTAL HARMONIC
DIS-
TORTION:
LBT-D170/LBT-G1100:
With 6 ohm loads, both
channels driven, from 70 —
20,000 Hz; rated 20 watts per
channel minimum RMS
"power, with no more than
10% total harmonic
distortion from 250
milliwatts to rated output.
LBT-D270/LBT-G3100 for
the U.S.A.:
With 8 ohm loads, both
channels driven, from 70 —
20,000 Hz; rated 100 watts
per channel minimum RMS
power, with no more than
0,9% total harmonic
distortion from 250
milliwatts to rated output.
CD player section
System
Compact disc and
digital audio system
Laser
Semiconductor laser
(A = 780 nm) Emission
duration: continuous
Laser output
Max 44.6 pW*
* This output is the value measured ata
distance of 200 mm from the objective
lens surface on the Optical Pick-up Block
with 7 mm aperture.
Wavelength
780 - 790 nm
Tuner section
FM stereo, FM/AM
superheterodyne tuner
FM tuner section
Tuning range
87.5 ~ 108.0 MHz
(100 kHz step)
Antenna
FM wire antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
330 - 1,710 kHz
(with the AM tuning
interval set at 10 kHz)
531 — 1,710 kHz
(with the AM tuning
interval set at 9 kHz)
AM loop antenna
External antenna
terminals
Intermediate frequency
450 kHz
Antenna
"For Your Information
2 1
Advertisement
Table of Contents
