Advertisement
VSX-511S REMOTE CONTROL OPERATION
The initial functions
can operate all products compatible
with
PIONEER's common system remote controf units marked with the
fey ey SS Ey CS
a
ad Id a
®
3s |lpasaell
®
Q PIONEER
REMOTE CONTHOL UNIT
Ket
@ RECEIVER POWER button
Switches the receiver power between ON and STANDBY.
@ Input selector buttons
Press when switching the receiver's INPUT SELECTOR.
The CONTROL MODE also switches to the same component {except
PHONO) {One CONTROL MODE button lights)
Pressing TAPE 1/DAT, TAPE 2 MONITOR, causes the CONTROL MODE
DECK il button to fight.
@® V. SEL (VIDEO SIGNAL SELECTOR) button
This switches just the video signal in sequence, leaving the sound
unchanged.
+ VCR 1—+ VCR 2—> LD —- TV — OFF
@ ACOUSTIC select button
The acoustic setting changes in the following manner each time this
button is pressed.
=
FLAT —+ LOUDNESS ae
E+-D-—C-—-B—A
@® SIMULATED STEREO button
When playing back a monaural source, press to switch the simulated
sterso function ON/OFF.
® SURR. (SURROUND) MODE button
The surround mode is switched in the following manner each time the
button is pressed:
pone STUDIO — SIMULATED — OFF — DOLBY PRO LOGIC
SURROUND
=]
@) 3CH LOGIC button
Switches DOLBY 3CH LOGIC on and off.
@® CENTER MODE button
When DOLBY PRO LOGIC SURROUND or DOLBY 3CH LOGIC are ON,
use to switch the center mode.
36
<ARB1378>
DOLBY PRO LOGIC SURROUND]
eS
Seige
PHANTOM
DOLBY 3CH LOGIC]
> NORMAL—
WIDE
@ DELAY TIME button
During DOLBY PRO LOGIC SURROUND and SIMULATED SURROUND
operation, delay time settings can be changed from 16 ms to 30 ms
in 2 ms steps.
The DELAY TIME button does not work with STUDIO and DOLBY
3 CH LOGIC.
@® BALANCE (L, R} buttons
Operate after switching the selector (8) to the left side (BAL display side).
@ AUTO SOURCE CONTROL buttons
(2 SLEEP timer button
Activates the SLEEP timer. The length changes in the following manner
each time the button is pressed.
———+ 90 —+ 60 —+ 30 — 0 (OFF)
Unit; minutes
When SLEEP is ON, the display section is about half as bright as when
SLEEP is OFF.
@ DISPLAY button
Does not operate with this unit.
@ RETURN button
Press the RETURN button to return the receiver into the initial state.
TUNER is selected at this initial state. Adjust the sound level by using
the MASTER VOLUME buttons,
® TAPE 2 MONITOR
. OFF
© FUNCTION ..
* SURROUND MODE....... OFF
© V-SIGNAL SEI
Sed
¢ MUTING
. OFF
TONE. scssevsccscccase
ce suave flat
® FRONT BALANCE... CENTER
The
HITS
function
searches
for broadcast
stations
among
the
frequencies displayed.
NOTE:
if no sound is output after the RETURN button is pressed, make sure
that SPEAKERS buttons are turned on.
i
@) MUTING button
Used to temporarily mute the sound.
The volume is restored when pressed again.
@ TEST TONE button
Use to adjust the test tone volume level from each speaker.
Operates when the DOLBY PRO LOGIC SURROUND
or DOLBY 3CH
LOGIC mode is selected.
When the test tone is switched ON, TEST is displayed in the display
section, and the test tone is output through each speaker in turn for
about two seconds, Adjust volume level so that it is the same from each
speaker.
@) MASTER VOLUME (+, -} buttons
Adjusts the overall volume.
REAR LEVEL/CENTER LEVEL (+, -} buttons and select switch
[Select switch: REAR LEVEL}
Adjusts the sound level of the rear speakers to the level of the front
speakers.
{Select switch: CENT. LEVEL]
Adjusts the center speaker sound ievei.
TUNER
a
Advertisement
