Advertisement
ENGLISH
Description
Versatile drill powered pump used to transfer non-explosive
or non-corrosive liquid from sinks, tanks, water heaters,
aquariums, window wells, bathtubs, etc. This pump is
designed to work with most power drills rated up to 2800
RPM. A drill with a minimum 1/4" chuck is required. NOTE:
DRILL SOLD SEPARATELY. Drill not included with any model. Tubing
& Hose included only with model BXWP60005
Safety Guidelines
Carefully read, understand and follow all safety instructions
in this manual.
This is the safety alert symbol. When you see this symbol,
look for one of the following signal words.
Important
Read these warnings carefully. Know the application and limitations of
this drill pump. Failure to follow these warnings could result in serious
bodily injury and/or property damage.
DANGER: Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE: Indicates to address practices not related to personal injury.
Specifications
Max Flow Rate at 2800 RPM at 0 ft. discharge height
Max Flow Rate at 800 RPM at 0 ft. discharge height
Maximum Discharge Head at 2800 RPM
Maximum Discharge Head at 800 RPM
Self-Priming Height
Min. Drill RPM (Recommended)
Max. Drill RPM
Drill Chuck Size
Construction
Suction
Discharge
Min Liquid Temp
Max Liquid Temp
Drive Shaft
3 in. x 3/8 in. Adapter Tube
30 in. x 1/4 in. Suction Tube
36 in. x 1/2 in. Garden Hose with female fitting
Drill not included with any model
2
DANGER: Fire hazard. Never pump gasoline or other volatile or flammable
liquids with this unit.
CAUTION: Follow all safety precautions recommended by the manufacturer of
the electric drill*.
CAUTION: Always disconnect drill from power source and remove the pump
from drill before attempting to service or perform maintenance.
WARNING RISK OF ELECTRICAL SHOCK: For corded or battery operated
drill* follow drill manufacturers instructions.
CAUTION: Inspect hoses and/or tubing before each use. Using worn or leaking
hoses can prevent the pump from working properly.
NOTICE: Suction hose/tubing should be as short as possible, kink free, and non-
collapsible. Be certain the suction line is air tight. Any leaks may prevent the pump
from priming.
NOTICE: Do not run the drill pump dry. The drill pump housing must be filled
with liquid during operation. Operating the drill pump dry for as little as 30 seconds
can cause damage and result in premature failure of the drill pump. Running the drill
pump dry will also void the warranty.
NOTICE: The drill pump is lubricated at the factory for the first use. It is
recommended to add a few drops of lubricating oil to the inlet port of the drill pump
before each use to aid with priming and to prevent the impeller from running dry.
Cooking oil or mineral oil are suitable options.
NOTICE: A screen or strainer (not included) should be used when pumping fluids
that contain abrasives or small solids to prevent damage to the pump.
BXWP60002
225 GPH (852 LPH)
140 GPH (530 LPH)
45 ft. (13.7 m)
32 ft. (9.7 m)
Up to 8 ft. (2.4 m) Vertically
800
2800
1/4 in. (6.4 mm) or Larger
Thermoplastic
3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
35° F (2° C)
120° F (48° C)
Corrosion Resistant Steel
Not Included
Not Included
Not Included
BXWP60005
225 GPH (852 LPH)
140 GPH (530 LPH)
45 ft. (13.7 m)
32 ft. (9.7 m)
Up to 8 ft. (2.4 m) Vertically
800
2800
1/4 in. (6.4 mm) or Larger
Thermoplastic
3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
35° F (2° C)
120° F (48° C)
Corrosion Resistant Steel
Included
Included
Included
Advertisement
