Table of Contents
Advertisement
Quick Links
This manual provides instructions for the following FieldServer products:
FS-X30 Series
FS-X35 Series
The instructions are effective for the above as of July, 2004
FieldServer Technologies
A Sierra Monitor Corporation Company
1991 Tarob Court, Milpitas, California 95035 USA
Phone: (408) 262-2299
Toll Free: (888) 509-1970
Fax: (408) 262-9042
Email: support@fieldserver.com
Web Site: www.fieldserver.com
FS-X30 Series
FS-X30 Start-up Guide
APPLICABILITY & EFFECTIVITY
Description
FieldServer
FieldServer
Applicability and Effectivity
Instruction Manual Part Number: T17004
Rev. A1.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FieldServer FS-X30 Series
Summary of Contents for FieldServer FS-X30 Series
- Page 1 Fax: (408) 262-9042 Email: support@fieldserver.com Web Site: www.fieldserver.com FS-X30 Series FS-X30 Start-up Guide APPLICABILITY & EFFECTIVITY This manual provides instructions for the following FieldServer products: Description FS-X30 Series FieldServer FS-X35 Series FieldServer The instructions are effective for the above as of July, 2004 Instruction Manual Part Number: T17004 Rev.
-
Page 2: Table Of Contents
Use PING to Identify the FieldServer on the Network ..........6 3.3. Connect using “Remote User Interface” (RUINET) ............6 3.4. Use RUINET to change the FieldServer IP Address and Network .......6 3.5. Upload the Default Configuration .................6 3.6. Change the Configuration File to Meet the Application ..........6 3.7. -
Page 3: Quick Start
Note that a default configuration file has already been loaded onto the FieldServer. Check the Driver Manual and the FieldServer Configuration Manual for further information on this file. Page 1... -
Page 4: Product Description
FieldServer or the Driver Kit. Then plug the connection adapter to the node. If using RS-485 from the node to the FS- X30, the + and - wire connections can be used on the RS-485 port on the FieldServer. Ethernet connections simply require... - Page 5 + DC In p u t 5.40” 6.30” 1.85" 1.95" Figure 2.1: Diagram of FieldServer FS X-30 Series showing dimensions, LED’s and all Connection Ports. Figure 2.2 – FS-X30 Series showing mounting options. Page 3 FS-X30 Series FieldServerStart-up Guide (08-2004)
-
Page 6: Supplied Connector Kit (Fs-8915-11)
The tables in the diagram show the functions applied to each of the RJ-45 pins by the FieldServer to assist in determination of the required pinout configuration for connection to the third party device. - Page 7 Instruction Manual Note: FS-X30 Series RS-232 numbering convention is reverse to the 10BaseT numbering convention. RJ45 M ale M odular Jack RJ45 Female Modular Jack Figure 2-2 RS-232/Cat 5 Wire Functions/Connections From PIN DESCRIPTION To DCE Frame Ground Transmitted Data...
-
Page 8: Operation
TCP/IP protocol. • on the FieldServer to ensure that the user If using Windows XP, ensure that the does not need to configure a FieldServer firewall is disabled. -
Page 9: Download The Updated Configuration File
"!" option (or simply cycle power to The simulation utility mb8sim.exe can be the FieldServer) to put the new file into used to test configuration files. This file can operation. Note that it is possible to do be found with the latest Utility CD (v.14 and... -
Page 10: Appendix A. Limited Warranty
FieldServer Technologies for damages including, but not limited to, consequential damages arising out of/or in connection with the use or performance of the product. -
Page 11: Appendix B. Led Functions
The run light should flash green once per second once the FieldServer has booted up. Note that it may take a while from power up to boot up the FieldServer if the loaded configuration is particularly large. The run light indicates that the FieldServer firmware is running. - Page 12 Instruction Manual THIS PAGE INTENTIONALLY LEFT BLANK. Page 10 FS-X30 Series FieldServerStart-up Guide (08-2004)
Need help?
Do you have a question about the FS-X30 Series and is the answer not in the manual?
Questions and answers