Table of Contents
Advertisement
Quick Links
About Your EXP 9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FCC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
EXP 9100 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Automatic Digital Code Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Auto Channel Scan and Auto Channel Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Spread Spectrum Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Auto Power Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing Your EXP 9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Selecting the Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the Telephone Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Base Unit on a Desk or Tabletop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting the Base Unit on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Battery Pack (BT-9100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preparing the Base Unit and Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using Your EXP 9100 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using your EXP 9100 Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the EXP 9100 as a Room Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Telephone Line Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Base Unit Controls & Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Handset Controls & Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table of Contents
1
Advertisement
Table of Contents
Related Manuals for Uniden EXP 9100
Summary of Contents for Uniden EXP 9100
-
Page 1: Table Of Contents
More Than One Cordless Telephone ........ -
Page 2: Important Safety Instructions
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. -
Page 3: Save These Instructions
E. If the product has been dropped, or the cabinet has been damaged. F. If the product exhibits a distinct change in performance. 13. Do not use the telephone to report a gas leak in the vicinity of the leak. CAUTION: TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS... -
Page 4: About Your Exp 9100
Nickel-Cadmium Battery Disposal Notice Memory Storage Stickers If any of these items are missing or damaged, do not contact the place of purchase. Instead, contact Uniden Customer Service at: (800) 297-1023 8 a.m. to 5 p.m., Central, Monday through Friday. FCC Requirements You are no longer required by the FCC to notify your local telephone company of your intent to connect a new telephone. -
Page 5: Exp 9100 Features
Many cordless telephones operate similarly and on the same frequency. Without digital code security, another Handset could make calls using your Base Unit and telephone line. Therefore, to avoid any unauthorized calls through your Base Unit, a Digital Code feature was added to your EXP 9100. -
Page 6: Auto Channel Scan And Auto Channel Change
If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will not function. To restore the Digital Code: Remove the Handset from the Base Unit (if it is on the Base Unit). Restore power to the Base Unit. -
Page 7: Installing Your Exp 9100
A modular jack converter (not included) is required. You may need to rewire when connecting the converter (making color-coded connections). (Note: Your Uniden Cordless Telephone Dealer or a telephone supply store can advise you on the proper adapter or converter. ) There are two telephone line jacks in the EXP 9100: “LINE IN”... -
Page 8: Installing The Base Unit On A Desk Or Tabletop
Telephone Line Cord (supplied) into the “LINE IN” jack on the Base. Plug the other end of the Telephone Line Cord into the telephone wall jack. Plug the AC Adapter cord into the AC Adapter input jack on the Base Unit. -
Page 9: Mounting The Base Unit On A Wall
Mounting the Base Unit on a Wall Installing the Wall-Mount Adapter on the Base Unit Remove the Handset from the Base Unit. Lay the Base Unit face down on a flat, smooth surface. Insert the two front tabs of the Wall Mount Adapter into the two receptacles next to the legs of the Base Unit. - Page 10 Base Unit; otherwise, damage to the Base Unit could result. Plug one end of the Telephone Line Cord (supplied) into the “LINE IN” jack on the Base Unit. Lay the cord inside the molding on the Wall Mount Adapter connected to the Base Unit.
-
Page 11: Installing The Battery Pack (Bt-9100)
Then hang the Handset on the Base Unit. Plug the other end of the Telephone Line Cord into the telephone wall jack. Plug the AC Adapter into a standard 120V AC wall outlet. Route the power cord where it will not create a trip hazard, or where it will not become chafed and create a fire or other electrical hazards. - Page 12 Charging the Handset’s Battery Pack The rechargeable Nickel-Cadmium Battery Pack must be fully charged before using your EXP 9100 for the first time. (Note: Allow the unit to charge without interruption for 5-7 hours. ) Place the Handset on the Base Unit. Make sure the CHARGE LED lights.
- Page 13 Base Unit Battery Back-Up Feature If AC power to the Base Unit fails, and the Spare Battery Charger contains a battery, the Base Unit will keep operating from the spare battery. This feature prevents the system from going dead during a power outage. Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the TALK LED flashes every 3 seconds.
-
Page 14: Preparing The Base Unit And Handset
NOTE: Refer to the foldout located in the back of this Operating Guide to help familiarize you with the features of your cordless phone. Preparing the Base Unit and Handset On the Base Unit, select either Pulse Dialing or Tone Dialing, depending on your local service. - Page 15 Answering a Call The Handset rings and the green TALK LED and Keypad Lights flash. If the Handset is not in the Base Unit, press TALK to answer the call. If the Handset is in the Base Unit, the AutoTalk feature allows you to answer the call by simply picking up the Handset and beginning your conversation.
-
Page 16: Special Features
Using the FLASH/R. TONE Button Press the FLASH/R. TONE button while operating the Handset. This feature sends a timed “hook-flash” on the telephone line for accessing services such as Call Waiting, etc. Last Number Redial Press RDL/P to dial the last number that you called. This feature is extremely useful when the number you called is busy. -
Page 17: Using Your Exp 9100 Memory
Using Your EXP 9100 Memory Storing a Number Remove the Handset from the Base Unit Press MEMO (The TALK LED lights and you hear a beep.) Enter the number (up to 16 digits) you want to store. You may enter a delay between numbers (for accessing a switchboard, or long distance service) by pressing RDL/P at the point in the number sequence you wish to pause. -
Page 18: Using Your Exp 9100 Intercom
Storing Mixed Tone/Pulse numbers: If your Base Unit is set up for Pulse Dialing, you can store a mixed mode number (up to 16 digits) to easily access long distance services or other services requiring Tone inputs. Follow steps 1 and 2 in “Storing a Number,” then: Enter the number to be dialed in Pulse Mode. -
Page 19: Using The Exp 9100 As A Room Monitor
Paging the Base Unit While a Call is Holding Press INT’COM on the Handset. If no answer, press TALK or INT’COM to disconnect and return to the call ON HOLD. At the Base Unit, press INT’COM to answer the page. Speak into the microphone. -
Page 20: Troubleshooting
If your EXP 9100 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service at: (800) 297-1023, 8 Monday through Friday. Note: Do not attempt to service this unit yourself. -
Page 21: Important Electrical Considerations
Telephone Line Problems The FCC has granted the telephone company the right to disconnect service in the event that your EXP 9100 causes problems on the telephone line. Also, the telephone company may make changes in facilities and services which may effect the operation of your unit. -
Page 22: Specifications
GENERAL Frequency Control Modulation Operating Temperature Base Unit Receive/Transmit Frequency : 903.087 to 925.615 MHz (23 Channels) Power Requirements Size Weight Handset Receive/Transmit Frequency : 903.087 to 925.615 MHz (23 Channels) Power Requirements Size Weight Battery Specifications shown are typical and subject to change without notice Specifications The EXP 9100 complies with FCC Part 15 and 68. -
Page 23: Base Unit Controls & Functions
® EXP 9100 Cordless Telephone Operating Guide... - Page 24 Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
-
Page 25: One Year Limited Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. - Page 26 ® © 1993 Uniden America Corporation. All rights reserved. ZUDUD01304AZ Printed in Hong Kong...
- Page 27 Base Unit Controls & Functions Tone/Pulse Fold Down Legs Base Unit Antenna Handset Retainer Battery Compartment Handset Support Charging Contacts Microphone Switch Line Out Ringer/Volume Line In Switch Intercom Button AC Adapter Connection Speaker Intercom LED Power LED Charge LED Battery Charge LED...
-
Page 28: Handset Controls & Functions
Handset Controls & Functions Handset Antenna Earpiece Hold Button Talk Button Mute Button 1 – 9, 0, # Buttons Tone Button One-Touch Buttons Memory Button Volume and Ringer Volume Button Ring On Battery Save Switch RING BATT SAVE Monitor Button Intercom Button Flash and Ringer Tone Button...