Advertisement
Quick Links
MH-400 Conveyor/Swivel/Caddy
Model No. 44938
Use of this product may cause exposure to chemicals known to the State of California
to cause cancer, birth defects, or other reproductive harm.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
119-6821
1. Warning—do not transport the machine when the conveyor
is extended; only transport the machine when the conveyor
is in the stored position.
119-6810
1. Read the Operator's Manual.
2. Use two people required to lift.
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
WARNING
CALIFORNIA
Proposition 65 Warning
decal119-6821
decal119-6810
Register at www.Toro.com.
119-0217
1. Warning—stop the engine; stay away from moving parts;
keep all guards and shields in place.
119-6851
1. Warning—do not stand on machine.
119-6834
1. Read the Operator's Manual.
2. Maximum load is 1500 lbs (680 kg)
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Form No. 3460-438 Rev A
Operator's Manual
decal119-0217
decal119-6851
decal119-6834
*3460-438*
Advertisement
Related Manuals for Toro MH-400
Summary of Contents for Toro MH-400
- Page 1 2. Use two people required to lift. decal119-6834 119-6834 1. Read the Operator's Manual. 2. Maximum load is 1500 lbs (680 kg) *3460-438* © 2022—The Toro® Company Original Instructions (EN) Register at www.Toro.com. 8111 Lyndale Avenue South Printed in the USA. Bloomington, MN 55420...
-
Page 2: Loose Parts
decal119-6850 119-6850 1. Crushing hazard of hand—use safety stand lock. Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Option caddy Handle Assemble the option caddy Handle Bolt (1/4 x 3/4 inch) Assemble the cross conveyor Flange lock nut (1/4 inch) –... - Page 3 (206 kPa) maximum. Procedure The option caddy is designed for one person to lift, transport, and mount the cross conveyor/swivel onto the MH-400. WARNING The option caddy has a maximum carrying load of 1500 lb (680 kg). Do not carry people...
- Page 4 Then re-install Install the option into the quick-attach brackets the lock rings over the lock pins and push down on the rear of the MH-400 (See the Installing the on the clamp handles Cross Conveyor/Swivel). Note:...
-
Page 5: Connecting The Hydraulic Hoses
Use Connect the hydraulic hoses to the option control cardboard or paper to find hydraulic leaks. valve on the MH-400 as follows (Figure Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Fluid •... - Page 6 g014112 Figure 4 1. Option control valve 4. Swivel kit 2. Hose connections 5. Cross conveyor 3. Quick attach clamps...
-
Page 7: Operation
Operation Remove the safety pins from both option attachment clamps on the swivel kit. Loosen the option attachment clamp brackets Operating the Cross Slide the conveyor to the center or side. Conveyor Re-tighten the clamp brackets. Re-install the safety pins. Extending and Retracting the On SH models adjust the speed of the cross Cross Conveyor... - Page 8 Operating the Swivel Kit To direct the flow of material from the cross conveyor in any direction, pull up the spring-loaded locking pin on the swivel kit into the unlock or open position. This allows you to manually move the cross conveyor freely from side to side on the swivel bearing (Figure To keep the cross conveyor in a fixed position, release...
- Page 9 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 10 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Regulations.
- Page 11 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.