Related Manuals for JETWAY G03-BFDADN1QIG-F
Summary of Contents for JETWAY G03-BFDADN1QIG-F
- Page 1 Quick Installation Manual NO. G03-BFDADN1QIG-F Rev: 1.0 Release Date: 2023-09-25 Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification.
-
Page 2: Safety Instructions
Safety Instructions 1. Read these safety instructions carefully. 2. Retain this user manual for future reference. 3. Disconnect the equipment from all AC outlets before cleaning. use only a damp cloth for cleaning. Do not use liquid or spray detergents. 4. - Page 3 I/O Outlets...
- Page 4 Dimension and Outlines I. To Dissemble the Chassis 1. Locate the screws at the spots marked on this side of the system and unscrew them one by one.
- Page 5 2. Remove the marked screw on the front IO panel. 3. Remove the marked screw on the rear IO panel. 4. Lift the cover up to open the chassis. 5. The overview of the internal structure of the system with HDD tray pre-installed.
- Page 6 6. Remove the marked screws to dissemble the HDD tray from the system. 7. The overview of the internal structure of the system.
- Page 7 II. To Install SO-DIMM to the board 1. Locate the SO-DIMM slot on the board. 2. Insert the gold-figure side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the break of the module fit into the notch of the slot and the golden-finger side should be fully plugged into the slot.
- Page 8 3. Press down to secure the SO-DIMM to the slot. The eject tabs will lock automatically if installing direction is correct.
- Page 9 III. To Install M.2 M-Key (2280) PCIe Card 1. Locate the M.2 M-Key PCIe (2280) slot on the board. Prepare compatible M.2 M-Key PCIe (2280) card. To install compatible card, please remove the screw in the marked spot at first. 2.
- Page 10 3. Tighten up the screw removed before to the marked spot to secure the card. Note: The screw post and nut fixed at location MH4 by default for 8cm type-2280 card installation.
- Page 11 IV. To Install M.2 E-Key (2230) USB 2.0/PCIe Card 1. Locate the M.2 E-Key PCIe (2230) slot on the board. Prepare compatible M.2 PCIe, type - 2230 card. 2. Remove the marked screw (MH2) and use it to lock compatible card to the slot in later installation.
- Page 12 3. Insert the gold-figure side of the compatible card into the slot and press down. See to it that the golden-finger side should be fully plugged into the slot. 4. Secure the card to the board by tightening up the screw to the marked spot.
- Page 13 5. Locate the reserved antenna holes on the rear panel. Remove the dust-proof plugs on the marked spots from the panel to install the antenna. 6. Push this antenna screw head into antenna hole of the rear panel from the backside of the panel.
- Page 14 7. And then lock the antenna screw head to the front side of the rear panel with the hexagonal screw nut② and tighten it up. 8. Press the metal hat on the end of the antenna string to corresponding antenna slot on the card as showed.
- Page 15 9. Repeat step 6 to 8, to finish installation of the other antenna. Notice: When all necessary installations are finished, please make sure that all cables unplugged before installations are connected to their original locations before restoring the back cover to the chassis and screws on the front panel/back panel/top cover locked to its original locations (Refer to Part I).
- Page 16 V. To Install Hard Disk Place compatible SATA HDD upon HDD tray as showed above. Plug this side of the cable to SATA power-in connector and SATA connector of the hard disk. Turn over the HDD tray and fix 2.5’’ HDD upon HDD tray by tightening 4* screws marked in corresponding spots.
- Page 17 Adjust the installed tray as showed above. Fix HDD tray into the system by tightening up 4 screws marked. (refer to I-6)
- Page 18 VI. To Wall Mount the system 1. Install wall mount rack to the system by tightening two screws in the marked positions. 2. Then lock the other two screws on the other side in the same way. 3. Wall mount the system by tightening 4 screws in the marked positions on both sides of the wall racks.