Table of Contents
Advertisement
Quick Links
Velocity 5.5" Touch Panel
AT-VTP-550-WH and AT-VTP-550-BL
The Atlona AT-VSP-550-BL and AT-VTP-550-WH are 5.5" touch panels in black and white,
respectively, for the Atlona Velocity™ Control System. They feature contemporary, refined styling
for modern presentation environments with 720x1280 native resolution, and a capacitive glass
surface that supports multi-touch and gesture interactions. These touch panels conveniently
install into a wall or furniture via a US or Euro one-gang opening. The VTP-550-BL and VTP-550-
WH feature Power over Ethernet (PoE), enabling a single network connection for data and power.
Setting up the touch panels is effortless as the AV control GUI is automatically uploaded from the
Velocity Control Gateway processor during system configuration.
Package Contents
1 x AT-VTP-550
1 x Metal mounting plate
Operating Notes
•
The Velocity 5" Touch Panel (AT-VTP-550) must be on the same network as the Velocity
Gateway (AT-VGW-HW) or it will be unable to sync for control.
•
The AT-VTP-550 is PoE capable, to power the unit, simply plug it into a 802.3at compatible
network switch. If the network switch is not PoE capable, a PoE injector
can be used.
IMPORTANT: Velocity Gateway (AT-VGW-HW) must be set up before the AT-VTP-550 is
fully functional.
4 x Mounting screws
1 x Installation Guide
1
Installation Guide
(purchased separately)
AT-VTP-550
Advertisement
Table of Contents
Related Manuals for Panduit ATLONA Velocity AT-VTP-550-WH
Summary of Contents for Panduit ATLONA Velocity AT-VTP-550-WH
- Page 1 Installation Guide AT-VTP-550 Velocity 5.5” Touch Panel AT-VTP-550-WH and AT-VTP-550-BL The Atlona AT-VSP-550-BL and AT-VTP-550-WH are 5.5” touch panels in black and white, respectively, for the Atlona Velocity™ Control System. They feature contemporary, refined styling for modern presentation environments with 720x1280 native resolution, and a capacitive glass surface that supports multi-touch and gesture interactions.
-
Page 2: Mounting Instructions
Installation Guide AT-VTP-550 Mounting Instructions The AT-VTP-550 can be mounted to a 1 gang back plate. Select the type of 1 gang back box to use and install into a wall. NOTE: Install using the region’s safety guidelines for electrical boxes. Thread the Ethernet cable through the 1 gang box. -
Page 3: Installation And Setup
Installation Guide AT-VTP-550 Installation and Set Up NOTE: Installation of the Velocity Touch Panel can only be done after Velocity has been set up. View the installation guides for VGW-HW/VGW-SW and Velocity Manual for instructions. Connect the Ethernet cable into the back of the unit. If the Ethernet cable is connected to a non PoE switch, use a PoE injector using 802.3at (purchased separately). - Page 4 Installation Guide AT-VTP-550 Scanning for Gateways Scanning for Gateways 10.0.0.234 CANCEL CANCEL Press the SCAN FOR GATEWAYS button. The touch panel will scan for new gateways. Once the correct gateway is found, press USE. On a network computer, use a browser to log into Velocity. Navigate to the room the VTP will be located in.
- Page 5 Installation Guide AT-VTP-550 Select the Edit button on the tile to open the unit settings. Enter the IP of the VTP into the IP Address field and select the save icon in the top right corner of the screen. The screen will close, the panel will sync to the gateway, and the room control will display on the panel.
-
Page 6: Advanced Settings
Installation Guide AT-VTP-550 Advanced Settings Once the touch pad has been set up, the settings can be changed or reset only through the advanced settings. To access the settings, swipe from the left side of the touch pad to the right. Select Advanced Setup. -
Page 7: Firmware Updating
Installation Guide AT-VTP-550 Firmware Updating The touch panel can be updated from within its settings menu. To update, the panel must be connected to a network with internet access. Swipe from the left side of the touch pad to the right to open the gateway settings menu. Select the ABOUT VELOCITY button. -
Page 8: Select Gateway
Installation Guide AT-VTP-550 Manual Firmware Updating The AT-VTP uses a .tar.gz firmware that can be downloaded from the firmware section of https:// atlona.com/product/vtp-550/. Once downloaded follow these instructions to update the firmware. NOTE: When downloading the firmware file on a MAC, ensure that the file is not being auto-extracted. -
Page 9: Warranty
Installation Guide AT-VTP-550 Warranty To view the product warranty, use the following link or QR code: https://atlona.com/warranty/. English Declaration of Conformity The English version can be found under the resources tab at: https://atlona.com/product/vtp-550/. Chinese Declaration of Conformity 中国RoHS合格声明 由SKU列出於: https://atlona.com/about-us/china-rohs/. International atlona.com 408.962.0515...