Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec BE60
Summary of Contents for Trotec BE60
- Page 1 BE60 INSTRUCTIONS DIGITAL TRUE RMS MULTIMETER WITH THERMAL IMAGING CAMERA...
-
Page 2: Table Of Contents
• Proceed with the utmost care when measuring voltages above 25 VAC rms or 35 VDC. There is a risk of an electric shock at these voltage levels. digital true RMS multimeter with thermal imaging camera BE60... - Page 3 Avoid direct sunlight and moisture. There is a risk of explosion! Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. digital true RMS multimeter with thermal imaging camera BE60...
-
Page 4: Information About The Device
Note The integrated Bluetooth function makes it possible to connect To prevent damages to the device, do not expose it to the device to a terminal device via the Trotec MultiMeasure extreme temperatures, extreme humidity or moisture. Mobile app. The measurement results can be displayed and saved on the Note terminal device either numerically or in form of a chart. - Page 5 0.3 to 0.6 possible is indispensable for a precise measurement. Limestone 0.95 to 0.98 Carborundum Ceramics 0.88 to 0.95 Gravel 0.95 Carbon, graphite 0.70 to 0.85 Carbon, not oxidized 0.8 to 0.9 digital true RMS multimeter with thermal imaging camera BE60...
- Page 6 COM socket Red measuring tip Black measuring tip Fold-out stand Fuse compartment (below stand) Holding fixture for measuring tips Infrared sensor closure Infrared sensor Work light USB connection mA/10 A socket MODE/RANGE button USB cable digital true RMS multimeter with thermal imaging camera BE60...
- Page 7 This measuring device is designed for REL indication indoor use and complies with PEAK indication measuring category CAT III up to 600 V MAX indication and measuring category CAT IV up to Battery status indication 300 V. digital true RMS multimeter with thermal imaging camera BE60...
- Page 8 1) The accuracy refers to a range from 10 % of the measuring 4 MΩ 0.001 MΩ range up to 100 %, sine wave. 40 MΩ 0.01 MΩ ± (2.5 % Input impedance: > 9 MΩ + 10 digits) Accuracy of the PEAK function: ± 10 %, PEAK response time: 1 ms digital true RMS multimeter with thermal imaging camera BE60...
-
Page 9: Transport And Storage
The accuracy specification consists of two values: • % value referring to the reading: Results from the accuracy of the measuring circuit. • + digits: Results from the accuracy of the analogue-to- digital converter. digital true RMS multimeter with thermal imaging camera BE60... -
Page 10: Operation
0.99 Language Chinese selection English German Italian Spanish French Dutch Polish Turkish Portuguese Setup Key sounds switch on/off Bluetooth Display brightness 10–100 % in increments of 10 % Auto Power OFF disabled/ 15/30/60 minutes digital true RMS multimeter with thermal imaging camera BE60... - Page 11 • Switch work light on/off: Press and hold Rotary switch (4): • Set type of measurement MODE/RANGE button (17): • Change measuring mode within the type of measurement set: Press briefly • Set range (decimal places): Press and hold digital true RMS multimeter with thermal imaging camera BE60...
- Page 12 3. Connect both measuring tips to the measuring object. ð The measured value will be indicated on the display. ð If the input voltage is negative, a minus (-) will appear in front of the measured value on the display. digital true RMS multimeter with thermal imaging camera BE60...
- Page 13 (in series; red to plus, black to minus). 6. Switch the measuring circuit back on and read the measured value from the display. digital true RMS multimeter with thermal imaging camera BE60...
- Page 14 3. Connect the measuring tips to the measuring object. ð If there is good continuity with a resistance below 50 Ω, a beep sounds. ð When the circuit is open, OL is displayed. digital true RMS multimeter with thermal imaging camera BE60...
- Page 15 ð The MAX indication (32) on the display shows that the maximum and minimum value function is active. 2. Press the OK/Hold button (2) to the left once again to exit the maximum and minimum value function and return to the measuring function. digital true RMS multimeter with thermal imaging camera BE60...
- Page 16 OK/Hold button (2) to the left. A prompt will then appear in the app asking whether you want to save the thermal image. 3. Press the OK/Hold button (2) to exit the hold mode and return to the current thermal image. digital true RMS multimeter with thermal imaging camera BE60...
- Page 17 Yes or No and confirm your selection. ð If you have selected Yes, all images stored on the thermal imaging camera will be deleted. 5. Press the MODE/RANGE button (17) to exit the indication of thermal images. digital true RMS multimeter with thermal imaging camera BE60...
-
Page 18: Multimeasure Mobile App
2. Make sure that the Bluetooth function is activated on the PEAK HOLD measuring device. 3. Start the Trotec MultiMeasure Mobile app on the terminal The last 12 values measured over time are displayed in the device. measured value field. ð A list of active and available sensors will be displayed. - Page 19 You can choose from saving or discarding the record after stopping recording. digital true RMS multimeter with thermal imaging camera BE60...
- Page 20 • Generate image overlay: Combines a background image with the representation of the measured values. • Colour scaling: Allows you to adjust the colour display of the measured values. digital true RMS multimeter with thermal imaging camera BE60...
- Page 21 Press the button to open the input mask for a new customer. You can create a new customer set or import an existing contact from the phone book of the terminal device. digital true RMS multimeter with thermal imaging camera BE60...
-
Page 22: Maintenance And Repair
5. Attach the cover and secure it by tightening the screw. 6. Fold back the stand (9). ð The charging screen is shown on the display. When the battery is fully charged, the Battery status indication (33) is completely green. digital true RMS multimeter with thermal imaging camera BE60... -
Page 23: Errors And Faults
Fuse replacement chapter. Only for United Kingdom • The device may be defective. Please contact the Trotec According to Waste Electrical and Electronic Equipment customer service. Regulations 2013 (SI 2013/3113) (as amended) devices that are no longer usable must be collected separately and disposed of in an environmentally friendly manner. -
Page 24: Declaration Of Conformity
Manufacturer and name of the authorised representative of the technical documentation: Trotec GmbH Grebbener Straße 7, D-52525 Heinsberg Phone: +49 2452 962-400 E-mail: info@trotec.de Place and date of issue: Heinsberg, 17.02.2023 Joachim Ludwig, Managing Director digital true RMS multimeter with thermal imaging camera BE60... - Page 25 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...