Advertisement
Quick Links
BLOODHOUND R19D
Installation Instructions
Table of Contents
Required Tools & Accessories ................................................................................................................................................................ 2
Battery and Router Installation .............................................................................................................................................................. 3
Connection: .................................................................................................................................................................................................... 6
Final Assembly ............................................................................................................................................................................................. 11
Operational Setup ..................................................................................................................................................................................... 13
Battery Operation and Safety Guidelines ....................................................................................................................................... 16
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Parsec Antennas BLOODHOUND R19D
Summary of Contents for Parsec Antennas BLOODHOUND R19D
-
Page 1: Table Of Contents
BLOODHOUND R19D Installation Instructions Table of Contents Required Tools & Accessories ................................2 Battery and Router Installation ................................3 Connection: ........................................6 Final Assembly ......................................11 Operational Setup ..................................... 13 Battery Operation and Safety Guidelines ............................16... -
Page 2: Required Tools & Accessories
120v) • USB-A Cord ** • Ethernet Cords, 4 pcs ** • Right-Angle Extension Cord, 3 FT • Router Options for Bloodhound R19D: o Cradlepoint R1900 with RX30 Managed Accessory, requires 12V 2x3 Power Supply (Cradlepoint #170870-000) * For connecting the router to the ports on the case... -
Page 3: Battery And Router Installation
Battery and Router Installation Step 1: Mount the OmniCharge 38K Battery Pack to the Cover Plate. A. This step only applies to the Bloodhound R19D. B. Cut and remove the flaps from the sides of the battery pack, shown in Figure 1. - Page 4 Ensure the router orientation is correct as shown in the images below. The router display should be visible through the slot(s) in the cover plate. Figure 4: Place the Cover Plate on the Antenna Plate. Figure 5: Install the Display Covers on the Cover Plate. Bloodhound R19D Installation Instructions Page 4 of 16...
- Page 5 Figure 6: Insert the R1900 Router into the Router Module. Figure 7: Mount the R1900 Router to the Cover Plate. Bloodhound R19D Installation Instructions Page 5 of 16...
-
Page 6: Connection
Connection: Figure 8: Connection Diagram for Bloodhound R19D Bloodhound Installation Instructions Page 6 of 16... - Page 7 Step 1: Connect the antenna cables to the router. A. Use canned air or isopropyl alcohol to clean all the connectors to ensure that there is no dust in the terminals. B. Connect the antenna cables to the designated terminals on the router, as shown in the tables and images below.
- Page 8 LTE 1 LTE 5 LTE 8 LTE 7 LTE 6 LTE 2 LTE 3 LTE 4 WIFI 1 WIFI 2 Power Supply For Managed Accessory Figure 9: Cradlepoint R1900 Connections...
- Page 9 Step 2: Connect the power supply to the router. A. Connect the router power supply to the power supply port on the managed accessory, shown in Figure 9. B. Plug the Right-Angle Power Cable into the Battery, shown in Figure 10. C.
- Page 10 Step 4: Connect the router to the RJ-45 ports on the case using ethernet cords. A. Connect the provided ethernet cords to the LAN ports on the router, shown in Figure 8. B. Connect the other ends of the ethernet cords from the router to the RJ-45 ports on the case. C.
-
Page 11: Final Assembly
Final Assembly Step 1: Make sure all the cables and devices are properly connected. A. Inspect every cable connection and ensure that no connections are loose. B. Use cable ties or other wire management to neatly bundle the cables as shown below. Ensure that the Antenna Cables are divided into two segments, as shown below, to ensure they do not press against the Power Adapter. - Page 12 Step 2: Fasten the cover plate to the case. A. Place the cover plate onto the bottom half of the case. Ensure that no cables are pinched between the cover plate and the case. B. Fasten the cover plate to the case using the twenty-one PTA0351 black oval head screws with washers provided in the kit, as shown in Figure 14.
-
Page 13: Operational Setup
Operational Setup Step 1: Open the fan and vent caps. A. Before turning the antenna ON, always open the fan and vent caps. The type of cap may vary. Ensure that the antenna is away from any liquids when the caps are open. Figure 15: Open the fan and vent caps. - Page 14 Step 3: Connect the antenna to a computer. A. Use an ethernet cable to connect a computer to one of the RJ-45 ports on the case that are connected to the LAN ports on the router. Step 4: Login to Cradlepoint NetCloud. A.
- Page 15 Step 5: Select the antenna in the device list on Cradlepoint NetCloud. A. On the left side of the page, select STATUS. From the dropdown menu, select INTERNET and then CONNECTIONS. B. In the Device List table, select the option with a cellular SIM, as shown in Figure 18. Figure 18: Select the device with a cellular SIM in Cradlepoint NetCloud.
-
Page 16: Battery Operation And Safety Guidelines
Battery Operation and Safety Guidelines A. To manually power ON/OFF, press and hold the power button (located on the top of the unit) for 3 seconds. All LED lights/display should turn ON/OFF. B. Recharging the battery pack can be done with the included 48W Charging Adapter or with a Type- C PD Charger with at least 45W of power and up to 65W maximum. - Page 17 CAUTION To comply with FOC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance. DO NOT •...
Need help?
Do you have a question about the BLOODHOUND R19D and is the answer not in the manual?
Questions and answers