KitchenAid NSF KSBC1B2 - Certified Commercial Enclosure Blender Manual

KitchenAid NSF KSBC1B2 - Certified Commercial Enclosure Blender Manual

Also See for NSF KSBC1B2:

Advertisement

KitchenAid NSF KSBC1B2 - Certified Commercial Enclosure Blender Manual

PARTS AND FEATURES

PARTS AND FEATURES

  1. Ingredient cap with measuring cup
  2. Lid
  3. Blender jar
  4. Talon blade
  5. Power cord socket and removable power cord (not shown)
  6. Cord cleat (not shown):
    To store the cord.
  7. Base
  8. On/off switch (not shown)
  9. Open handle for easy stackability
  10. Removable blender jar pad
  11. Control dial
  12. Pulse toggle switch
  13. Start/Stop toggle switch
  14. Status indicator light
  15. Tamper
  16. Front cover with Handle
  17. Back cover
  18. Thumb Screw

GETTING STARTED

First, clean all parts and accessories (see "Care and Cleaning" section). Place the blender in a dry and clean area.

PRODUCT FUNCTION GUIDE

The Blender has a preset recipe program: Icy Drinks, Variable speeds, and Pulse functions.

Setting Description Blending Time (in min: sec) Suggested Items to Blend
Icy Drinks Incorporates icy drink ingredients at low speed, then ramps up to high speed for a complete blend. 0:22 Ice, whole fruits or vegetables, or frozen fruits. Drinks such as Margaritas, Daiquiris, and blended ice coffee drinks.
Low The Blender will run on low speed until the Start/stop is pressed, or will stop after 6 minutes. N/A
Med The Blender will run on medium speed until the Start/stop is pressed, or will stop after 6 minutes. N/A
High The Blender will run on high speed until the Start/stop is pressed, or will stop after 6 minutes. N/A
Pulse H/L Use Pulse during manual operation to add a boost of power. N/A
Variable Times Starts at a slow speed and ramps up to a high speed for optimal blending results. 0:05-0:60

DEVICE ASSEMBLY

  1. Install the back cover by aligning the tab on the rear side of the base with the slot on the back cover.
    DEVICE ASSEMBLY - Step 1 - Install the back cover
  2. Secure both sides over the tabs on the either side of the blender base.
    DEVICE ASSEMBLY - Step 2
  3. Install and secure the thumb screws on both sides by hand.
    DEVICE ASSEMBLY - Step 3 - Install thumb screws
  4. Secure the front cover to the back cover.
    DEVICE ASSEMBLY - Step 4 - Install the front cover

burn hazardburn hazard
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

  1. Make sure the power switch is OFF. Securely attach the removable power cord into the back of blender. Plug the Blender into a grounded 3 prong outlet.
    DEVICE ASSEMBLY - Step 5 - Plug in the unit
  2. Flip the power switch to ON (I). The status indicator light will flash, indicating that the Blender is in Standby mode and ready to operate.
    DEVICE ASSEMBLY - Step 6 - Flip the power switch

USING THE DEVICE


When moving your Blender, always close the Front cover and support/lift from the Blender base. Base will become disengaged from jar if carried by Blender jar or Blender jar handle only. Do not lift by the cover or cover handle.

  1. Add items (max. 60oz). Add liquids first, then soft foods, then leafy greens, and ice or frozen items last. Secure the lid.
    USING THE DEVICE - Step 1 - Adding items
  2. Open the front cover. Place the blender jar on the base, aligning with the jar pad. Close the Front cover.
    USING THE DEVICE - Step 2 - Placing a blender jar
  3. Turn the control dial to your desired speed, time, or program. Flip the START/STOP toggle switch up or down to start. See the "Product function guide" for more details.
    USING THE DEVICE - Step 3
  4. Using the Tamper (optional): Open front cover. Remove the Ingredient cap only. Stir or press contents down towards the blade. When finished, replace the Ingredient cap before resuming blending.
    USING THE DEVICE - Step 4 - Using the tamper
  5. Using the Pulse mode (optional): Press and hold the PULSE toggle switch up for a faster pulse, or down for a slower pulse.
    NOTE: The Pulse function may also be used on its own as a separate blending function while the Blender is in Standby mode.
    USING THE DEVICE - Step 5 - Using the pulse mode
  6. When finished, flip the START/STOP toggle switch up or down to stop. Allow the Blender to completely stop before removing the lid or pouring out the blended ingredients.
    NOTE: Icy Drink cycle and variable timer cycles will stop automatically at the completion of the cycle.
    USING THE DEVICE - Step 6 - Turning off the unit

CARE AND CLEANING

NOTE: Do not immerse the Blender base or cord in water. Do not use abrasive cleansers or scouring pads to avoid scratching.

  1. Fill half of the jar with warm water and add 1 or 2 drops of dish-washing liquid. Secure the Lid and Ingredient Cap. Place the jar on the base. Close the front cover.
    CARE AND CLEANING - Step 1
  2. Rotate the control dial to 50 seconds. Flip the START/STOP toggle switch up or down. When the timer finishes, remove and empty contents and rinse with warm water and dry thoroughly.
    CARE AND CLEANING - Step 2
  3. Unplug before cleaning. Wipe the base and the cord with a warm, damp cloth and dry with a soft cloth.
    CARE AND CLEANING - Step 3 - Wipe the base
  4. Wash the blender jar, jar pad, lid, front cover, back cover, handle, and ingredient cap by hand with a damp cloth and warm soapy water; rinse with warm water, and dry with a soft cloth.
    CARE AND CLEANING - Step 4

NOTE: Handle must be removed from the front cover prior to cleaning by removing the two screws inside the front cover.

SANITIZING THE BLENDER JAR

  1. Remove all contents from the blender jar.
  2. Fill ¾ of the jar with a sanitizing solution mix of 1.5 tsp. (7.4 mL) institutional or household bleach in 60 oz (1.75 L) water. Place the lid, and securely place the blender jar onto the blender base.
  3. Run the blender on the High Speed setting for 35 seconds.
  4. Turn off to let the sanitizing mix sit in the blender jar for an additional 2 minutes.
  5. Pour out the solution. Do not rinse the blender jar.
  6. Place the lid on the blender jar. Make sure the empty blender jar is fully in place on the blender base. Run the empty Blender for an additional 10 seconds. Do not rinse the jar after sanitizing.
  7. Allow the blender jar to air dry.

TROUBLESHOOTING GUIDE

burn hazardburn hazard
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Problem Solution
Status indicator light is off while unit is plugged in and On/Off switch is in On position: After 10 minutes of no activity, the blender will go into Sleep mode. Flip START/STOP toggle switch up or down to bring the blender back into Standby mode.

Status indicator light is flashing orange color

Indicates error mode. This can be caused by: using a spatula or any other utensil that could obstruct the blade to freely spin, or having an ice cube or hard food in a location that locks up the blade.

Unplug the blender and remove the jar from the base, and clear the items. Place the jar back on the base, and then turn on the blender to continue regular use.

The unit stops after continuously running for 6 minutes

This is normal operation for variable speed functions. Refer to "Product function guide" for details.

The unit stops while blending

If blender stops prior to the completion of the selected function, contact an authorized service center for assistance.

If the ingredients of a recipe aren't blending

An air pocket can be created around the blade causing the ingredients to miss the blade. Use the tamper to push ingredients down into the blade. Refer to "Using the commercial blender" section. For certain recipes, adding more liquid may also assist in incorporating the ingredients.

Blender jar overflows

Unplug and remove the jar pad from the housing to make sure the base is fully dry. The control dial can be detached by pulling it off with force. Wipe dry, and then replace it back.

Troubleshooting does not solve the problem

See the "Warranty and service" section. Contact an Authorized Service Center for assistance.

Do not return the Blender to the retailer – retailers do not provide service.

WARRANTY AND SERVICE

ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRES, OR ORDERING ACCESSORIES AND REPLACEMENT PARTS
In the United States and Puerto Rico:
For service information, or to order accessories or replacement parts, call toll-free at 1-855-845-9684 or write to:
Customer eXperience Center,
KitchenAid Small Appliances,
P.O. Box 218, St. Joseph, MI 49085-0218

Outside the United States and Puerto Rico:
Consult your local KitchenAid dealer or the store where you purchased the Commercial Blender for information on how to obtain service.

For service information in Canada:
Call toll-free 1-800-807-6777.

Or write to:
Customer eXperience Centre
KitchenAid Canada
200 - 6750 Century Ave.
Mississauga, ON L5N 0B7

PRODUCT SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

warning This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.
You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

  1. Read all instructions.
  2. shock hazard To protect against risk of electrical shock, do not put Blender in water or other liquid.
  3. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
  4. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
  5. Avoid contact with moving parts.
  6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair or adjustment.
  7. Do not use outdoors.
  8. Do not let cord hang over edge of table or counter.
  9. Keep hands and utensils, other than the tamper provided, out of the container while blending to reduce the risk of severe injury to persons or damage to the blender. The cover must remain in place when using the tamper through the cover opening. A scraper may be used but must be used only when the blender is not running.
  10. Blades are sharp. Handle carefully.
  11. Always operate Blender with cover in place.
  12. The use of attachments, including canning blender jars, not recommended by KitchenAid may cause a risk of injury to persons.
  13. Do not use appliance for other than intended use.
  14. When blending hot liquids or ingredients, Ingredient Cap should remain in place over the lid opening. Always start on lowest speed and slowly ramp to desired speed when blending hot liquids or ingredients.

SAVE THESE INSTRUCTIONS
This product is designed for commercial use.

ELECTRICAL REQUIREMENTS

burn hazardburn hazard
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Voltage: 120 V
Frequency: 60 HZ
Amps: 15.0 A

NOTE: If the plug does not fit in the outlet, contact a qualified electrician. Do not modify the plug in any way. Do not use an adapter.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

MOTOR HORSEPOWER

Motor horsepower for the blender motor was measured using a dynamometer, a machine that laboratories routinely use to measure the mechanical power of motors. Our 3.0 peak horsepower (HP) motor reference reflects the horsepower output of the motor itself and not the Blender's horsepower output in the blender jar. As with any blender, the power output in the jar is not the same as the horsepower of the motor itself.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download KitchenAid NSF KSBC1B2 - Certified Commercial Enclosure Blender Manual

Advertisement

Need Assistance?

Do you have a question about the NSF KSBC1B2 that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents