Pioneer XR-J11 Operating Instructions Manual page 16

BASIC OPERATIONS
4. Press the • (REC) button.
• Recording begins.
5. Play the recording source.
6. To stop recording, press
M/A
(STOP/EJECT) button.
Do not operate Deck I when recording on Deck II.
NOTE:
If beat noise is recorded during reception of an AM broadcast, place
the AM loop antenna away from this unit and video cassette
recorder.
Pausing and restarting recording
1. Press Deck IIII (PAUSE) button.
• Recording will be suspended.
2. To restart recording again, press II (PAUSE) button.
DOLBY NR SYSTEM (Except for Australian
and multi-voltage models of XR-J11)
The Dolby NR Systems are designed to reduce high-frequency tape
hiss noise generated during playback.
The level of low-volume, high-frequency sounds is increased during
recording, and decreased by the same amount during playback to
restore the original level. At the same time, high-frequency noise
(the most easily perceived by the human ear) is attenuated.
Dolby B-type NR system reduces high-frequency tape noise,
widening the dynamic range.
NOTE:
Avoid playing back tapes reduced using the Dolby NR system with
DOLBY NR switch in the OFF position, or tapes recorded without
Dolby NR system with DOLBY NR switch in the ON position, since this
does not allow faithful reproduction of the original sound.
SYNCHRO COPY (TAPE COPY)_
In order to copy from one cassette tape to another follow this
procedure:
If a tape recorded with the DOLBY NR system is copied, the
copied tape will also be recorded automatically with DOLBY NR
system.
If a tape recorded without the DOLBY NR system is copied, the
copied tape will also be recorded automatically without the
DOLBY NR system.
1. Set the input selector to TAPE, press the
M/A
(STOP/EJECT)
button, then insert the cassette to be copied into Deck I
compartment and insert a blank cassette into Deck II
compartment.
2. Press the (II) PAUSE button on Deck I, and then press the ►
(PLAY) button.
3. Press the • (REC) button on Deck II.
• Deck I will start playing back and Deck II will start recording.
• Tape copying is unaffected by the volume and graphic equalizer
settings.
4. Press the
M/A
(STOP/EJECT) button on both decks to stop the
copying at anytime.
PLAYING THE COMPONENTS CONNECTED j
TO VIDEO JACKS_|
1. Set input selector button on the amplifier to VIDEO.
2. Play the component connected to VIDEO jacks.
[compact disc play
Operation procedures before playback
I (Inserting a disc)
(See
Fig.(7])
1. Press OPEN/CLOSE button.
The disc tray will be ejected forward.
COMPU TRACK
1 2 3
A
5 : ! ! : Is 5 6
7 8
ill : •
■
9 10 1 1 12
2. Place a disc on the disc tray.
Insert the disc on the disc tray while following the respective disc
guide (8 cm or 12 cm disc guide), as shown in the figure.
NOTE:
• When setting an 8 cm CD, do not use the 8 cm CD adaptor.
• Be sure to place the disc on the tray with the label side upward.
• Hold the disc so that you do not touch the playing side (the
iridescent side) with your hands or fingers.
• If both 8 cm and 12 cm discs are inserted and played
simultaneously, the disc may be scratched or malfunction may
result Insert only one disc at a time.
3. Press OPEN/CLOSE button, or gently push the disc tray in
with your fingers.
After insertion of the disc tray, the total number of tracks on the
disc and the total playback time will be displayed for about 5
seconds.
COMPU TRACK
1
a 3 A
:
1
: :
■
• •
5 6 7
B
i
J sj'L J
9
ID
11 12
16
<ARB7008>