Advertisement
holes can be 5/16 or 3/8 inch diameter.
Replace the
plastic
cover
and
install
the
handrail
as
described
above.)
2.12
HEIGHT GAUGE ASSEMBLY
If your seale was ordered with a height gauge
follow the installation directions packed with the height
gauge.
2.20
§102 PHYSICIAN'S OFFICE SCALE
Carefully
remove
all parts
from the
shipping
carton.
Inspect all components for shipping damage.
The only assembly required for this scale is to mount
the flat pack readout to a wall at a convenient reading
height.
Preferably pick a location near an electrical
receptacle.
Detach
the
mounting
bracket
from
the
readout by removing the two top screws on both sides
of the readout.
A %" Allen hex wrench is supplied for
this purpose.
The
method
of fastening
will vary
according to the type of wall. Mount the bracket to the
wall with appropriate mounting hardware such as dry-
wall fasteners, "molly-bolts", screws, etc. (not included
with scale).
Reassemble the readout to the bracket by
re-installing the two previously removed screws.
Place the platform on the floor in the desired position.
NOTE:
The platform should be six to ten inches away
from the wall for proper operation (so the patient's body
will not touch the wall).
Connect the transducer cable
between the platform and the readout. Insert the power
cord's plug into an electrical outlet.
Handrails are not available for this scale.
2.30
5602 PORTABLE SURVEY SCALE
Carefully remove all parts from the shipping
carton.
Inspect all components for shipping damage.
This scale is shipped fully-assembled from the factory.
Simply
connect
the
transducer
cable
between
the
platform and
readout.
For proper use, the platform
should be placed on the floor, and the readout can be
held or placed on a table.
Handrails are not available for this scale.
240
6002 WHEELCHAIR SCALE
NOTE:
In some cases the 6002 scale may be shipped
in an assembled condition thus eliminating the need for
assembly.
Carefully remove
all parts from the shipping
carton.
Inspect the components for shipping damage.
Place the scale base on a floor or work bench.
The
interior cable that connects the readout to the weighing
platform will be tucked up inside the mast. Carefully pull
the end with the connector out of the bottom of the
mast.
Insert the mast into the base with the readout
facing the black weighing platform. Be sure the interior
cable is routed properly and not pinched by the mast.
Fasten the mast with the bolts and washers provided.
It is important to tighten the bolts securely to insure a
stable and solid connection.
Align the plastic connector of the interior cable with its
mate, located on the base near the bottom of the mast.
The connector will only mate one way.
If it does not go
together turn it over and try again.
Press it together
firmly for a good connection.
Be sure to tuck any slack
cable inside the mast so it will not drag on the floor.
241
WEIGHING DECK MOUNTING
The weighing deck is mounted to the scale by
four (4) special flat head screws.
The deck must be
positioned so that the two sets of holes (under the flaps)
ate closest to the mast.
These
holes are used for
mounting the handrail.
Line the weighing deck up with
the mounting holes in the aluminum
plate.
Install four
Y"
flat
head
screws
(supplied)
through
the
deck.
Tighten the mounting screws securely with the hex Alten
wrench provided.
2.42
HANDRAIL
If you have ordered the handrail for the scale
install it now by fastening it to the weighing deck. The
mounting feet of the 6002 handrail are attached to the
underside
of the weighing
deck with the hardware
provided.
Each
foot of the handrail attaches to the
platform with the two flat head screws
and
special
locking nuts provided.
It is important to tighten the
screws and nuts securely.
If you did not order the handrail at the time of the
6
5002, 5102, 5602, 6002, 6102, 6202, 6502, 6702
Advertisement
