Jabra GN9120 Manual
Flex nc microphone with ehs
Hide thumbs
Also See for GN9120:
- User manual (75 pages) ,
- Reference manual (74 pages) ,
- Quick setup manual (10 pages)
Advertisement
Quick Links
Jabra GN9120 Flex NC Microphone With EHS
How to connect my Jabra GN9120 EHS / GN9125 EHS with
Nortel IP 1120E, 1140E, 1150E, 1165E
Prerequisite:
Jabra GN9120 EHS + Jabra Link 14201-32 (from FW 2.2.0)
Jabra GN9125 EHS + Jabra Link 14201-32 (from FW 2.2.0)
In combination with one of the following phones:
Nortel IP 1120E
Nortel IP 1140E
Nortel IP 1150E
There is a minimum revision level (UNIStim 5.2) needed when using our
EHS adapter on Nortel 1140e with CS2100 server. The CS1000 is OK
with 3.1 or greater. It can be downloaded from
http://support.nortel.com.
Connection:
1. Connect the 1-sided end (USB plug) of the EHS adapter with the USB
socket on your phone phone.
2. Insert the RJ10 plug into the socket identified with the "phone"
symbol and the RJ45 plug into the socket identified with "AUX" on
the base.
EHS setup:
The Jabra GN912x must support and be set up on DHSG EHS.
Proceed as follows to check the EHS installed:
https://www.jabra.in/supportpages/jabra-gn9120/9120-28-11/faq/50e3d2d4-4986-
4d9b-b283-11c16b2ceb5f
23/01/2024 09:32
Page 1 of 4
Advertisement
Related Manuals for Jabra GN9120
Summary of Contents for Jabra GN9120
- Page 1 23/01/2024 09:32 Jabra GN9120 Flex NC Microphone With EHS How to connect my Jabra GN9120 EHS / GN9125 EHS with Nortel IP 1120E, 1140E, 1150E, 1165E Prerequisite: Jabra GN9120 EHS + Jabra Link 14201-32 (from FW 2.2.0) Jabra GN9125 EHS + Jabra Link 14201-32 (from FW 2.2.0)
- Page 2 3. With the PLUS or MINUS buttons, you can now switch between the different EHS types. 4. To confirm the EHS has successfully installed, the base automatically switches back to charge mode after approx. 10 seconds. Base setup: Set the phone set-up switch (A-G) to "A". https://www.jabra.in/supportpages/jabra-gn9120/9120-28-11/faq/50e3d2d4-4986- Page 2 of 4 4d9b-b283-11c16b2ceb5f...
- Page 3 If they see "password", enter default: "26567*738" then follow the below info. If they see "Preferences", then they choose "3" for headset/active headset device and select "USB". Be https://www.jabra.in/supportpages/jabra-gn9120/9120-28-11/faq/50e3d2d4-4986- Page 3 of 4 4d9b-b283-11c16b2ceb5f...
- Page 4 23/01/2024 09:32 sure "HID commands" is enabled. Press "apply" to save the settings. Also be sure phones (idle & active) ring settings are set to "default". https://www.jabra.in/supportpages/jabra-gn9120/9120-28-11/faq/50e3d2d4-4986- Page 4 of 4 4d9b-b283-11c16b2ceb5f...