Advertisement
Wiring the Outside WAVE TO OPEN Sensor
(CM-331/42WS-SGLR)
Wire in power to the TB1 terminal block on the back lower left
side (not polarity sensitive). On terminal block TB3, wire the
common and normally open poles of the relay to Dry1 & Input
on the CX-33. The Remote terminal (TB2) will be wired in parallel
with the Remote terminal (TB2) of the Inside WAVE TO LOCK.
Then it's wired to Relay 3 (common & normally open) of the
CX-33. Install the SGLR (light ring) circuit board on the front-face
of the Outside WAVE TO OPEN sensor.
Confirm the DIP switch settings using the legend below. Adjust
the range accordingly with POT1 and POT 2 for the desired
activation time.
Wiring the Inside WAVE TO OPEN Sensor
(CM-325/42WS)
Wire in power using the two red wires (not polarity sensitive).
Next, connect the Blue wire (normally open) and the green wire
(common) to Dry2 & Input on the CX-33.
The range and the activation time can be adjusted from the
front-face of the sensor. The range adjustment is on the top and
the activation time is located on the bottom.
Wiring the Inside WAVE TO LOCK Sensor
(CM-331/43WS)
Wire in power to the TB1 terminal block on the back lower left
side (not polarity sensitive).
On terminal block TB3, wire the common and normally open
poles of the relay to Dry3 & Input on the CX-33.
The Remote terminal (TB2) will be wired in parallel with the
Remote terminal (TB2) of the Outside WAVE TO OPEN. Then it's
wired to Relay 3 (common & normally open) of the CX-33.
Install the SGLR (light ring) circuit board on the front-face of the
Inside WAVE TO LOCK sensor.
Confirm the DIP switch settings using the legend below. Adjust
the range accordingly with POT1 and POT2 for the desired
activation time.
Once all field devices are wired to the CX-WC16PS then AC
power can be wired in.
IMPORTANT: Do not apply power to the unit until you
have fully read the instructions and have made the
required adjustments.
The supplied CX-TRX-5024 transformer will have its secondary
terminals wired to the terminals on the top of the left terminal
strip marked as "AC".
Next, wire the primary terminals to the AC feed to be used.
Confirm your connections and apply power by turning on the
electrical panels breaker.
WC16PS SERIES RESTROOM CONTROL
Selecting a Mode
The CX-WC16PS has two Restroom applications built in (Mode 7
& 8). The default mode for the CX-WC16PS is Mode 7
(normally unlocked).
Determining which mode is correct for you will be based on
whether the Restroom will be normally unlocked (Mode 7) or
normally locked (Mode 8).
There are three LED displays that will allow you to see what mode
you have selected when advancing through the modes.
To change the mode of the CX-WC16PS, simply press the
MENU button once and use the UP button to advance to the
desired mode.
Editing the Settings for a Mode
Camden builds in typical times for lock release and door
operator activation and is ready to use without changing any
parameters. If you need to change the timing or delay for an
output, it can be done by pressing the "MENU" button within the
mode you selected.
Once the option is selected you can use the "UP or DOWN"
buttons to select the timing needed. The first option
(H & 1 flashing) will be how long relay 1 will be activated for
(0-50 seconds).
The second option (d & 1 flashing) will be how long to wait
before activating relay 2 (0-15 seconds).
The third option (H & 2 flashing) will be how long relay 2 will be
activated for (0-50 seconds).
The fourth option (d & 2 flashing) will be how long to wait before
activating relay 3 (0-15 seconds).
The fifth option (H & 3 flashing) will be how long relay 3 will be
activated for (0-50 seconds). See chart below.
Factory Reset (Defaulting the CX-33)
To return the CX-33 back to its factory default settings you will
need to remove power, then hold down the "MENU" button
while powering up the CX-33.
Once started you will see the firmware version listed then a
number "1" will be displayed. Reconnect your power and press
the "MENU" button once then use the "UP" or "DOWN" button to
advance to the desired mode.
Fully test the operation of the CX-WC16PS for proper
functionality.
IN S TALL AT ION INSTRUCTIO NS
Page 2 of 13
Advertisement
