Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Keysight N2763B
Summary of Contents for Keysight N2763B
- Page 1 Keysight N2763B Rack Mount Kit for 4000G X-Series Oscilloscopes INSTALLATION GUIDE...
-
Page 2: Warranty
Keysight shall not be liable for errors or for A WARNING notice denotes a commercial computer software or incidental or consequential damages in commercial computer software hazard. - Page 3 This guide contains instructions for installing the Rack Mount Kit for 4000G X-Series Oscilloscopes. The Rack Mount Kit provides a support shelf and hardware for mounting Keysight 4000G X-Series oscilloscopes into Electronic Industries Association (EIA) standard 19-inch (487-mm) rack cabinets.
- Page 4 N5470-03701 Rack Mount Rail, Qty. 2 N2763-01201 Top Clamp N2763-68702 Rack Tray Assembly Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 5 N2763-24106 Top Trim Plate N2763-24104 Side Trim Plate, Qty. 2 N2763-68703 Bottom Trim Plate Assembly Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 6 3030-1768 Rack Mount Kit for 4000G X-Series Oscilloscopes...
-
Page 7: Installation
Installation Installation You will need the following tools to install the Rack Mount Kit: • T20 Torx driver. • #2 Phillips screwdriver. To perform the installation: 1 Set the oscilloscope on its back. Remove the T20 screw from each leg. T20 screw 2 Set the oscilloscope onto the N2763-68702 Rack Tray Assembly. - Page 8 Installation 3 Secure the oscilloscope to the Rack Tray Assembly using (Qty. 2) 0515-0456 screws. 0515-0456 screw 4 Remove the oscilloscope’s strap handle using a Torx T20 driver. handle removed Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 9 Installation 5 Attach the N2763-01201 Top Clamp to the top of the oscilloscope using (Qty 2) 0515-2049 screws. 0515-2049 screws Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 10 Installation 6 Attach the two N5470-03701 Rack Mount Rails to your rack using (Qty. 4) 2360-0806 screws and (Qty. 4) 0590-0804 nuts. Four 2360-0806 screws, 0590-0804 nuts Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 11 Installation 7 Slide the assembled oscilloscope and Rack Tray Assembly into the rack. 8 Secure the two Side Trim Plates to the rack using (Qty. 4) 3030-1768 screws and (Qty. 4) 0590-0804 nuts. Assembly may be easier if you slightly lift the oscilloscope to align the holes.
- Page 12 Installation 9 Secure the N5470-24102 Top Trim Plate to the rack using (Qty. 2) 3030-1768 screws and (Qty. 2) 0590-0804 nuts. 3030-1768 screws, 0590-0804 nuts Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 13 Installation 10 Bottom Trim Plate: a Optional: If you plan to connect cables from the oscilloscope to the BNC feedthroughs, connect them now. It may be difficult to connect them after securing the bottom trim plate. b Optional: If you plan to route the MSO cable through the notch in the Bottom Trim Plate, route it now.
- Page 14 Installation Rack Mount Kit for 4000G X-Series Oscilloscopes...
- Page 16 This information is subject to change without notice. © Keysight Technologies, Inc. 2012, 2023 Printed in Malaysia First Edition, October 2023 *N2763-97001* N2763-97001 www.keysight.com...
Need help?
Do you have a question about the N2763B and is the answer not in the manual?
Questions and answers