Schenck process Intecont Tersus Beltweigher Instruction Manual page 157

P05.07 - AO Speed ......................................................................................................................................................... 70
P05.08 - Speed Offset ...................................................................................................................................................... 70
P05.09 - Speed Range ..................................................................................................................................................... 71
P06 - Limit Values ............................................................................................................................................................ 71
P06.01 - Limit Actual Flow Rate MIN .............................................................................................................................. 71
P06.02 - Event Actual Flow Rate MIN ............................................................................................................................. 71
P06.03 - Limit Actual Flow Rate MAX ............................................................................................................................. 71
P06.04 - Event Actual Flow Rate MAX ............................................................................................................................ 72
P06.05 - Limit Load MIN.................................................................................................................................................. 72
P06.06 - Event Load MIN ................................................................................................................................................ 72
P06.07 - Limit Load MAX ................................................................................................................................................ 72
P06.08 - Event Load MAX ............................................................................................................................................... 72
P06.09 - Limit Speed MIN ............................................................................................................................................... 73
P06.10 - Event Speed MIN .............................................................................................................................................. 73
P06.11 - Limit Speed MAX .............................................................................................................................................. 73
P06.12 - Event Speed MAX ............................................................................................................................................ 73
P07 - Filters ...................................................................................................................................................................... 73
P07.01 - Filter Actual Flow Rate ...................................................................................................................................... 73
P07.02 - Filter Actual Flow Rate analog .......................................................................................................................... 73
P07.03 - Filter Belt Load.................................................................................................................................................. 74
P07.04 - Filter Belt Speed ............................................................................................................................................... 74
P07.05 - LC Filter ............................................................................................................................................................. 74
P07.06 - Afterflow Totalizer .............................................................................................................................................. 74
P08 - AUTO Zero Set ........................................................................................................................................... 74, 75, 76
P08.01 - Auto Zero Active ................................................................................................................................................ 74
P08.02 - Limit Value Difference ........................................................................................................................................ 74
P08.03 - Mean Limit Value ............................................................................................................................................... 75
P08.04 - Zeroing Limit ...................................................................................................................................................... 75
P08.05 - Event Tare Correction ....................................................................................................................................... 75
P08.06 - Zero Set Time .................................................................................................................................................... 75
P08.07 - Event Time elapsed .......................................................................................................................................... 75
P08.08 - Print Result ........................................................................................................................................................ 76
P08.09 - Zero Set Difference ............................................................................................................................................ 76
P08.10 - Event Tare Difference > MAX ........................................................................................................................... 76
P08.11 - Zero Drop-Out Active ......................................................................................................................................... 76
P08.12 - Zero Drop-Out Limit ........................................................................................................................................... 76
P09 - Batch Mode ............................................................................................................................................................ 76
P09.01 - Pre-cut-off Amount ............................................................................................................................................. 77
P09.02 - Correction Amount ............................................................................................................................................. 77
P09.03 - Adaptation Factor .............................................................................................................................................. 77
P09.04 - Batch Tolerance + ............................................................................................................................................. 77
P09.05 - Batch Tolerance - .............................................................................................................................................. 77
P09.06 - Event Out of Tolerance ..................................................................................................................................... 78
P09.07 - Belt Empty ......................................................................................................................................................... 78
P09.08 - Event Batch > Setpoint ..................................................................................................................................... 78
P09.09 - Batch Setpoint Source ....................................................................................................................................... 78
P09.10 - Batch Automatic Record .................................................................................................................................... 78
P09.11 - Reset print FMZ 1 .............................................................................................................................................. 79
P09.12 - Reset print FMZ 2 .............................................................................................................................................. 79
P10 - Printer Setting ............................................................................................................................................. 79, 80, 81
P10.01 - Baud rate ........................................................................................................................................................... 79
P10.02 - Print Subtotal ..................................................................................................................................................... 79
P10.03 - Print after STOP ................................................................................................................................................ 79
P10.04 - Print Page Length .............................................................................................................................................. 80
P10.05 - Batch Setpoint Line ............................................................................................................................................ 80
P10.06 - Batch Setpoint Column ...................................................................................................................................... 80
P10.07 - Batch Actual Value Line ..................................................................................................................................... 80
P10.08 - Batch Actual Value Column ............................................................................................................................... 80
P10.09 - FMZ 1 Line ........................................................................................................................................................ 80
P10.10 - FMZ 1 Column ................................................................................................................................................... 80
P10.11 - FMZ 2 Line ........................................................................................................................................................ 80
P10.12 - FMZ 2 Column ................................................................................................................................................... 81
P10.13 - Date/Time Line .................................................................................................................................................. 81
P10.14 - Date/Time Column ............................................................................................................................................. 81
P10.15 - Event Line .......................................................................................................................................................... 81
P10.16 - Event Column .................................................................................................................................................... 81
INTECONT® Tersus Belt weigher, Instruction Manual
Schenck Process Group
Index
BV-H2464GB, 1234
- 151 -