Blaze B600 Operating Instructions Manual
Contemporary styled wood heaters
Hide thumbs
Also See for B600:
- Operating instructions manual (12 pages) ,
- Installation instructions manual (11 pages) ,
- Installation instructions manual (20 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Blaze B600
Summary of Contents for Blaze B600
- Page 1 OPERATING INSTRUCTIONS Contemporary Styled Wood Heaters...
- Page 2 BLAZE B600/B900 Glen Dimplex Australia proudly supports the activities of Landcare Australia through its membership of the AHHA. BLAZE B605/B905 VERSION 1.0...
-
Page 3: Table Of Contents
TABLE OF CONTENTS USER INSTRUCTIONS MAINTENANCE AND SERVICING Introduction ......Replacement of Fire Bricks ....1.1. -
Page 4: User Instructions
User Instructions INTRODUCTION WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN Before use of this appliance please read these Swallowing may lead to serious injury in as little instructions fully. as 2 hours or death, due to chemical burns and WARNING: ANY MODIFICATION OF THE APPLIANCE potential perforation of the oesophagus. -
Page 5: Air Controls
1.1. AIR CONTROL 1.3. FAN The Blaze B600/B900 and B605/B905 wood heaters The fan can be used to spread heat around the feature a single air control system. It is designed room quicker, as well as distribute heat into other to introduce oxygen into the base of the fire, rooms. -
Page 6: Using Appliance For The First Time
USING APPLIANCE FOR THE FIRST LIGHTING THE FIRE TIME Place firelighters or paper and dry kindling wood in the base of the firebox. The power cable for the Blaze B600/B605 and B900/B905 may be bundled in the rear of the unit Light the paper or firelighters. for transportation. Ensure that the cable is pulled clear from the heater before lighting. -
Page 7: Low Heat Output
BURNING TIPS 5.2. LOW HEAT OUTPUT The heat output of the appliance can be 6.1. FUEL QUALITY reduced by closing the air slide, which will restrict Use wood with a moisture content of less than the oxygen supplied to the fire and slow down the 20%. Logs should not feel moist or damp, or have rate at which the wood burns. -
Page 8: Ash Removal
10. CLEANING THE FLUE ● High and gusty winds Check inside of flue prior to each season for any ● Outside temperature and weather build-up of creosote (wood tar). To do this: conditions First remove the baffle (refer to “2. ● Blocked flue Replacement of Baffle Plate” under Maintenance & Servicing section). For advice on the correction of persistent flue problems consult your supplier/installer. Using a small mirror and torch hold the mirror ASH REMOVAL on an angle below the flue with the torch shining at it and look for black creosote... -
Page 9: Troubleshooting Tips
11. TROUBLESHOOTING TIPS 11.1. GLASS IN DOOR BLACKENING This can have several possible causes: ● Burning unseasoned wood — if the wood is too wet, it will cause the glass to blacken. ● Appliance operated at low temperature — after an overnight burn where the air slide control has been fully closed, the glass may have blackened. When the fire is re-stoked and burning on the high heat setting, the... -
Page 10: Maintenance And Servicing
To remove the baffle: Replace with new bricks, and refit the Remove bricks from firebox. Lift the baffle retainer which holds the bricks in place. up at the back enough to clear the rear B600/B605 brick layout: support pegs. With the rear of the baffle plate still elevated, slide it forward, up and over the front row of support pegs, and out. -
Page 11: Removing The Door
REPLACING THE ASH PLATE ADJUSTING THE DOOR HINGE The ash plate protects the front of the firebox Over time the screws securing the door hinge below the door from the hot coal bed and fire. plate to the heater may loosen resulting in the door dropping, i.e. visually appears on slight angle Over time the ash plate may burn through, in and no longer perfectly horizontal. -
Page 12: Fitting New Door Glass
FITTING NEW DOOR GLASS FITTING A NEW DOOR SEAL This task may be easier with the door removed This task may be easier with the door removed from the heater and laid flat on a work-bench. from the heater and laid flat on a workbench. To replace the door glass: Remove any old seal from the door. Remove the six M8 button head screws and Clean out the groove in the door that the twelve washers securing the glass retainer to... -
Page 13: Door Handle Adjustment
DOOR HANDLE ADJUSTMENT Remove washer from door handle assembly: Over time, the door seal can become Remove the nut from the door handle compressed resulting in a less than adequate shaft inside the door. seal between the door and the front edge of the Remove the latch and remove one firebox. For example, if the wood burns unusually washer. -
Page 14: Receiver Replacement
Australia Pty Ltd (referred as “Glen Dimplex”). Unplug the power lead before proceeding. This warranty is provided to the first domestic purchaser of a Blaze Wood or Stove Fire (radiant To access the remote control receiver: or convection). It applies for 10 years from the date of purchase from or through an authorized B600/B900: Blaze Fire Distributor in relation to each product. - Page 15 What is covered under this warranty? ● Travel costs for a distance greater than 50 km from the nearest approved Blaze ● Repair or replacement of parts Heating Service Agent. ● Labour costs relating to the Wood or Stove ●...
-
Page 16: Replacement Spare Parts List
11. REPLACEMENT SPARE PARTS LIST PART MODEL DETAIL B600/B605 N900-253 5 @ 220 x 175 x 25mm 2 @ 220 x 85 x 25mm Fire Bricks Set 1 @ 220 x 140 x 25mm B900/B905 N900-285 10 @ 270 x 175 x 25mm... - Page 20 Glen Dimplex Australia Pty Ltd 8 Lakeview Drive, Scoresby Victoria 3179 Australia T: 1300 554 155 General & Sales Enquiries: flame.care@glendimplex.com.au Technical Service: flame.support@glendimplex.com.au www.glendimplex.com.au...
Need help?
Do you have a question about the B600 and is the answer not in the manual?
Questions and answers