Related Manuals for MCZ TEIA COMFORT AIR 10 S2
Summary of Contents for MCZ TEIA COMFORT AIR 10 S2
- Page 1 INSTALLATION GUIDE SEALED PELLET STOVE TEIA COMFORT AIR 10 S2 TEIA COMFORT AIR 10 UP! S2 PART 1 - REGULATIONS AND ASSEMBLY Instructions in English...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS ....................II INTRODUCTION ......................1 1-WARNINGS AND WARRANTY CONDITIONS ..............2 2-INSTALLATION .......................11 3-DRAWINGS AND TECHNICAL FEATURES ..............19 4-UNPACKING ......................24 5-HOW THE STOVE ARRIVES ..................28 6-REMOVING THE TOP ....................29 7-REMOVING THE UPPER PANEL ................30 8-CLADDING ASSEMBLY .....................31 9-OPENING THE DOORS .....................37 10-COMFORT AIR ......................38 11-LOADING THE PELLETS ..................40... -
Page 3: Introduction
No part of this manual may be translated into other languages, adapted and/or reproduced, even in part, in other mechanical and/or electronic form or media, for photocopies, recordings or other, without the prior written authorisation of MCZ Group Spa. The company reserves the right to make changes to the product at any time without prior notice. The owner company reserves its rights according to law. -
Page 4: 1-Warnings And Warranty Conditions
1-WARNINGS AND WARRANTY CONDITIONS SAFETY WARNINGS • The installation, electrical connection, operating test and maintenance must only be carried out by a qualified operator. • Install the product in compliance with the laws and regulations in force. • Only use the fuel recommended by the manufacturer. The product must not be used as an incinerator. - Page 5 1-WARNINGS AND WARRANTY CONDITIONS • Do not dry laundry on the product. Any drying racks or the like must be kept at a safe distance from the product. Fire hazard. • The product maintenance operations must be exclusively carried out by a qualified operator on a yearly basis.
- Page 6 1-WARNINGS AND WARRANTY CONDITIONS • Do not allow the product to come into contact with water, it contains live electrical parts. • Do not wash the product with water (or other liquids) as they could penetrate inside the unit, damaging the electrical insulation with the risk of electrocution. •...
- Page 7 1-WARNINGS AND WARRANTY CONDITIONS • The sound pressure level of this appliance does not exceed 70 dB(A). • Live electrical parts: only power the product once it has been fully assembled. • Disconnect the product from the 230V power supply before performing any maintenance operations.
- Page 8 1-WARNINGS AND WARRANTY CONDITIONS INFORMATION: • Please contact the retailer or qualified personnel for any information, problem or malfunction. • Only use the fuel specified by the manufacturer. • When the product is switched on for the first time, it is normal for it to emit smoke due to the paint heating up for the first time. Therefore make sure the room it is installed in is well-ventilated.
- Page 9 1-WARNINGS AND WARRANTY CONDITIONS WARRANTY CONDITIONS For the duration, terms, conditions, limitations of the MCZ conventional warranty, please refer to the specific warranty card that is included with the product. Information for management of waste electrical and electronic equipment containing batteries and accumulators This symbol appears on the product, on the batteries, on the accumulators or on their packaging or on their documentation;...
- Page 10 1-WARNINGS AND WARRANTY CONDITIONS WARNINGS FOR THE CORRECT DISPOSAL OF THE PRODUCT The owner is the sole party responsible for demolishing and disposing of the product. This must be performed in compliance with laws related to safety and environmental protection in force in his/her country. At the end of its working life, the product must not be disposed of as urban waste.
- Page 11 1-WARNINGS AND WARRANTY CONDITIONS LEGENDA WHERE TO DISPOSE MATERIALS Metal Glass If there is any, to be disposed of separately based on the material used: Tiles or ceramics OUTER CLADDING Stone Glass ceramic (fire door): to be disposed of with inert or mixed waste If there is any, to be disposed of separately based on the material used: Tempered glass (oven door): to be disposed...
- Page 12 The EC Declaration of Conformity, the Declaration of Performance required by EU Regulation 305/2011 and all other product certification documents can be downloaded by scanning the QR code on this page (also found on the product label) or by accessing the website page www.mczgroup.com/support/mcz Having specified the above, we highlight and report that: •...
-
Page 13: 2-Installation
2-INSTALLATION The instructions in this chapter refer explicitly to the Italian installation regulation UNI 10683. In any case, always observe the regulations in force in the country of installation. PELLETS The pellet is obtained from natural dried wood sawdust (without paint). The compactness of the material is guaranteed by the lignin contained in the wood itself, without glue or binders. - Page 14 2-INSTALLATION FOREWORD The heating system (generator + combustion air supply + combustion product expulsion system + any hydraulic/aeraulic system) must be installed in compliance with the laws and regulations in force , and carried out by a qualified technician, who must issue a declaration of conformity of the system to the system manager and shall undertake full responsibility for final installation and consequent good operation of the product.
- Page 15 2-INSTALLATION MINIMUM DISTANCES Observe the distances from flammable objects (sofas, furniture, wood panelling, etc..) as specified in the following diagram. If objects considered to be particularly sensitive to heat are present, such as furniture, curtains or sofas, as a precaution, increase the stove clearances substantially to avoid possible deterioration due to the effect of heat.
- Page 16 2-INSTALLATION In any case, ensure adequate distance to facilitate access during cleaning and extraordinary maintenance. If this is not possible, it must still be possible to distance the product from adjacent walls/elements. This operation must be performed by a technician qualified to disconnect the combustion product expulsion ducts and their subsequent restoration.
- Page 17 2-INSTALLATION Below 15kW: Air duct diameter Maximum length Maximum length (smooth duct) (corrugated duct) 50mm 60mm 80mm 100mm Above 15kW: Air duct diameter Maximum length Maximum length (smooth duct) (corrugated duct) 50mm 60mm 80mm 100mm Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 18 2-INSTALLATION Preparing the smoke expulsion system The combustion product expulsion system is a particularly important element for the proper operation of the appliance and must be correctly sized according to EN 13384-1. Its creation/adaptation/verification must always be carried out by a legally qualified operator and must comply with the regulations in force in the country where the appliance is installed.
- Page 19 2-INSTALLATION Chimneypot The chimneypot, meaning the end part of the flue, must meet the following characteristics: • the smoke outlet section must be at least double the internal section of the chimney; • prevent the penetration of rain or snow; •...
- Page 20 2-INSTALLATION EXAMPLES OF INSTALLATION (DIAMETERS AND LENGTHS TO BE SIZED) 1. Flue installation with hole for the passage of the pipe increased by: • minimum 100mm around the pipe if next to non-flammable parts such as cement, brick, etc.; or •...
-
Page 21: 3-Drawings And Technical Features
3-DRAWINGS AND TECHNICAL FEATURES DRAWINGS AND CHARACTERISTICS TEIA COMFORT AIR 10 S2 STOVE DIMENSIONS Ø60 Ø80 Ø60 Technical Dept. - All rights reserved - Reproduction prohibited... - Page 22 3-DRAWINGS AND TECHNICAL FEATURES TEIA COMFORT AIR 10 UP! S2 STOVE DIMENSIONS Ø60 Ø60 Ø80...
- Page 23 3-DRAWINGS AND TECHNICAL FEATURES TECHNICAL SPECIFICATIONS TEIA COMFORT AIR 10 S2 Energy Efficiency Class Nominal output power 10.0 kW (8600 kcal/h) Minimum power output 3.5 kW (3010 kcal/h) Efficiency at Max 90.4% Efficiency at Min 91.5% Temperature of exhaust smoke at Max 212 °C...
- Page 24 3-DRAWINGS AND TECHNICAL FEATURES TECHNICAL SPECIFICATIONS TEIA COMFORT AIR 10 UP! S2 Energy Efficiency Class Nominal output power 10.0 kW (8600 kcal/h) Minimum power output 3.5 kW (3010 kcal/h) Efficiency at Max 90.4% Efficiency at Min 91.5% Temperature of exhaust smoke at Max 212 °C Temperature of exhaust smoke at Min 108 °C...
- Page 25 ACCORDING TO COMMISSION REGULATIONS (EU) 2015/1185 - (EU) 2015/1186 (PRODUCT FICHE) MCZ GROUP SpA Manufacturer: Trademak: Model Identifier: TEIA COMFORT AIR 10 S2 / TEIA COMFORT AIR 10 UP! S2 Indirect heating functionality: Direct heat output (space heat output): 10,0 Indirect heat output (water heat output):...
-
Page 26: 4-Unpacking
4-UNPACKING INSTRUCTIONS FOR PACKAGING DISPOSAL The material that the appliance’s packaging is made of must be managed correctly, in order to make collection, reuse, recovery and recycling easier, where possible. The table below illustrates the possible components that the packaging is made of, and the relative instructions for correct disposal. DESCRIPTION CODE MATERIAL SYMBOL... - Page 27 4-UNPACKING Handle the product with suitable means paying attention to the applicable safety regulations in force. Do not turn the packaging over and handle the majolica parts with care. The stoves are delivered in a single package with steel sides packaged together with the structure and placed at the side. Open the package, remove the cardboard, polystyrene and any straps and position the stove in the preset place making sure that it complies with the requirements.
- Page 28 4-UNPACKING REMOVING THE FASTENING BRACKETS Remove the stoves from the pallet by removing the two screws “u” and the plate “s” from the stove foot. There are four “s” brackets.
- Page 29 4-UNPACKING Position the stove and connect it to the flue pipe. Use the 4 adjustable feet (J) to get the stove correctly levelled so that the smoke outlet (S) is lined up with the connecting pipe (H). If the stove needs to be connected to an outlet pipe which goes through the rear wall (to connect to the flue), take utmost care to make sure that the joint is not forced.
-
Page 30: 5-How The Stove Arrives
5-HOW THE STOVE ARRIVES On delivery, the Ego stove has no metal cladding and with the top fitted, as shown in the image below. Take the box with the metal sides (figure below) and prepare them for installation. The sides are fitted with screws for fixing to the structure. -
Page 31: 6-Removing The Top
6-REMOVING THE TOP To assemble the sides of the stove it is necessary to remove the top “C” from the structure. Lift the pellet cover by simply grasping it by the handle and pulling it towards you. Remove the two screws “y” from under the cover. Now remove the entire top “C”... -
Page 32: 7-Removing The Upper Panel
7-REMOVING THE UPPER PANEL REMOVING THE UPPER PANEL Panel “D” is already fixed to the stove structure, it may be removed in the event of maintenance, servicing or cleaning. After removing any top and sides, remove screws “k”, two on the right and two on the left, and remove the top front panel “D”. -
Page 33: 8-Cladding Assembly
8-CLADDING ASSEMBLY LOWER PANEL ASSEMBLY From the coating packaging take: • lower panel “B” • 4 screws “x” • 2 notched washers “r” Secure the panel “B” to the stove using the screws “x” and the washers “r”. Technical Dept. - All rights reserved - Reproduction prohibited... - Page 34 8-CLADDING ASSEMBLY SIDE PANEL ASSEMBLY Take from the packaging: • 1 side panel “A” (they are reversible) • 2 screws “x” • 2 washers “r” Insert the holes “u” on the bottom of the panel “A” on the hooks “z” in the structure of the stove.
- Page 35 8-CLADDING ASSEMBLY Then move panel “A” towards the structure and secure it with the two screws “x”. Place the M5 notched washer “r” between the screw “x” and the panel “A”. Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 36 8-CLADDING ASSEMBLY Fit the panel “A” on the other side in the same way.
- Page 37 8-CLADDING ASSEMBLY After completing the installation of the metal panels, refit the top “C” and secure it to the structure with the previously removed screws. Technical Dept. - All rights reserved - Reproduction prohibited...
- Page 38 8-CLADDING ASSEMBLY ACCESS TO THE ELECTRONIC BOARD The circuit board “J” is on the right side (handle side). If you need to access the board, you must remove the back side panel as explained above. ACCESS TO THE GEARMOTOR You must remove the side panel to access the gear motor “U”.
-
Page 39: 9-Opening The Doors
9-OPENING THE DOORS DOOR OPENING To open the firebox door “R”, insert the cold handle “z” into the hole in the handle and pull it towards you. Attention! The firebox door must be closed properly for the stove to work correctly. Only open the doors when the stove is switched off and cold. -
Page 40: 10-Comfort Air
10-COMFORT AIR Comfort Air ducting Comfort Air stoves can channel the air into other rooms through the connection with the accessory pipes to the rear “S” shaped flange provided as per standard. The recommended maximum duct length is 8 metres per fan. It is advisable to set up ducts of similar length to distribute the hot air evenly in the various rooms. - Page 41 10-COMFORT AIR Attention! It is mandatory to install the vents with “V” netting (1 or 2 depending on the type of appliance) on the rear “S” output for safety purposes and to prevent the rear wall from being hit directly by the hot air flow, generating halos, blackening or even dangerous heating in the case of flammable walls.
-
Page 42: 11-Loading The Pellets
11-LOADING THE PELLETS LOADING THE PELLETS Fuel is loaded from the upper part of the stove by lifting the door “C” and the pellet loading door “E”. Pour the pellets in slowly so that they are deposited at the bottom of the hopper. If loading pellets when the stove is running, open the door of the tank using the stove mitten that comes with the stove itself. -
Page 43: 12-Electrical Connection
12-ELECTRICAL CONNECTION ELECTRICAL CONNECTION First connect the power cable to the back of the stove and then to a wall socket. It is recommended to disconnect the power cable when the stove is not used. The cable must never come into contact with the smoke exhaust pipe or any other part of the stove. ELECTRICAL STOVE CONNECTION STOVE POWER SUPPLY Connect the power cable to the back of the stove and then to a wall socket. - Page 44 MCZ GROUP S.p.A. Via La Croce n°8 33074 Vigonovo di Fontanafredda (PN) – ITALY Telephone: 0434/599599 a.s. Fax: 0434/599598 Website: www.mcz.it e-mail: mcz@mcz.it 8902247200 REV 0 24/02/2023...