Table of Contents
Advertisement
#S – Enter Setup Password .................................24
#S= – Store Setup Password ...............................24
Callback Security Reset #CBR.................................23
Caller ID Query +VRID.............................................22
Caller ID S0..............................................................27
Caller ID Selection +VCID=......................................22
Carriage Return Character S3 .................................27
Carrier Loss Disconnect Time S10...........................27
Cisco Configuration %R ...........................................16
Command Mode Description......................................5
Command Mode Time %DT.....................................16
Command Speed Response %S..............................16
Command String ........................................................5
Communication Standard Setting B ...........................9
Compression Control %C.........................................15
Configuration Storing &W.........................................13
Country Code Display I9 ..........................................10
D
Data Calling Tone C.................................................15
Data Calling Tone S35 .............................................27
Data Carrier Detect &C ............................................12
Data Compression Control %C ................................15
Data Mode Description...............................................5
Data mode O............................................................11
Data Set Ready ControL &S ....................................13
Data Terminal Ready &D .........................................12
DCD Control &C.......................................................12
Default Settings &F ..................................................12
Default Settings Cleared &W1 .................................13
Definition of an AT Command ....................................5
Delay Timer S18 ......................................................27
Diagnostic Information Display I11...........................10
Dial D .........................................................................9
Dial Stored Telephone Number DS=n......................10
Dialing Tones S11....................................................27
DID commands
*DD – Digit Format ...............................................25
*DF – Format for Reporting Incoming DID Number
..........................................................................26
*DN – Number of DID Digits Expected .................25
*DS – Start Protocol .............................................25
*DT – Wait for Digit Time-Out Time ......................25
*DW – Busy-Out Timer .........................................26
DID Start Protocol *DS.............................................25
Digit Format *DD ......................................................25
Digital Loss (56K) with PBX S108 ............................29
Direct Connect Enable %H ......................................16
Disconnect Delay S10..............................................27
Display Current Settings &V.....................................13
Distinctive Ring +VDR=............................................22
DSR Control &S .......................................................13
DTR (Data Terminal Ready) Control &D ..................12
DTR Dialing $D ........................................................16
E
Echo E .....................................................................10
Echo Online Data Characters F ...............................10
Enable Dialing Message %M ...................................10
Enable V.34 Modulation S28....................................27
Enable/Disable 56K Auto Rate S42 .........................28
Enter Setup Password #S ........................................24
Error Control Setting S36 .........................................27
Error Control Setting S48 .........................................29
Multi-Tech Systems, Inc. AT Commands Reference Guide (PN S000272E)
Error Correction Mode Selection \N .........................14
Escape Character S2 ...............................................27
Escape Sequence +++AT ........................................24
Escape Sequence Description ...................................5
Escape Sequence for Remote Configuration
%%%ATMTSMODEM ..........................................24
F
Factory Default Settings &W1 ..................................13
Fallback and Fall Forward %E .................................16
Firmware Version Display I0 ....................................10
Firmware Version Display I4 ....................................10
Flow Control Selection &K .......................................13
Flow Control Selection \Q ........................................15
Format for Entering AT Commands ...........................5
Format for Reporting Incoming DID Number *DF.....26
G
Guard Tone Control &G ...........................................12
H
Hangup Delay S10 ...................................................27
Hangup H .................................................................10
Hook Control H.........................................................10
I
Inactivity Timer S30..................................................27
Inactivity Timer \T.....................................................15
Information Request I...............................................10
Initialization String ......................................................5
L
Leased-Line Operation &L .......................................13
Line Feed Character S4 ...........................................27
Load Factory Settings &F.........................................12
Local Callback Inactivity Timer #CBI........................23
Long Break $LB .......................................................16
M
Maximum 56K Connect Speed S38 .........................28
Maximum Speed S37...............................................28
MNP 5 Data Compression %C.................................15
MNP Error Correction \N2 ........................................14
Modem Baud Rate $MB...........................................17
Modem on Hold Enable +PMH=...............................18
Modem on Hold Initiate +PMHR=.............................18
Modem on Hold Timer +PMHT= ..............................19
Modem Reset Z........................................................12
Modulation Handshake N.........................................11
Modulation Selection +MS= .....................................21
Monitor Speaker Mode M .........................................10
N
Number of DID Digits Expected *DN........................25
O
On-hook/off-hook H..................................................10
Online Command Mode Description ..........................5
P
Parity Setting #P ......................................................24
Pause Time for Comma Setting S8..........................27
Chapter 3 – Result Codes
32
Advertisement
Table of Contents
