1. Manuals
  2. Brands
  3. PC Partner Manuals
  4. Motherboard
  5. BSB871S
  6. Manual

PC Partner BSB871S Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-
REORIENT OR RELOCATE THE RECEIVING ANTENNA
-
INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
-
CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
-
CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION
TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result
in harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to
operate this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for errors
or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective owners.
Electronic Emission Notices
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BSB871S and is the answer not in the manual?

Questions and answers

Related Manuals for PC Partner BSB871S

Summary of Contents for PC Partner BSB871S

  • Page 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 2: Table Of Contents

    Table of Contents HARDWARE CONFIGURATION .............. 3 Key Features ....................3 Motherboard Layout (Model Code No. - 35887100XX) ....... 5 Jumper Settings ..................6 CPU Speed Selection ................6 JP1 - Host Bus Speed Select ..............6 JP4 - CMOS Clear .................. 6 JP15 - Firm Ware Hub Top Block Memory Protect ........

  • Page 3: Hardware Configuration

    HARDWARE CONFIGURATION This motherboard is based on the Intel® 810 chipset that is the first generation Integrated Graphics chipset designed for the Intel® Celeron® PPGA Processor. The graphics accelerator architecture consists of dedicated multi-media engines executing in parallel to deliver high performance 2D, 3D, and motion compensation video capabilities.
  • Page 4 • Two USB ports (via a header). • Keyboard port (factory option for PS/2 type). • PS/2 mouse port (via a header). • Infrared (IrDA) support (via a header). • One Line / Speaker out, one Mic in, one Line in and MIDI / Gameport (via a header).

  • Page 5: Motherboard Layout (Model Code No. - 35887100Xx)

    Motherboard Layout (Model Code No. - 35887100XX) The following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. Warning: All connectors on board are labeled Pin “1” at one conner. Ribbon cables should always be connected with the red stripe on the Pin “1”...

  • Page 6: Jumper Settings

    Jumper Settings This chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. JP29 JP34 JP16 JP17 CPU Speed Selection In this motherboard, jumperless feature is implemented such that no jumper is required to be set for different type of CPU installed.

  • Page 7: Jp15 - Firm Ware Hub Top Block Memory Protect

    JP15 - Firm Ware Hub Top Block Memory Protect JP15 Selection (Open)* Locked* (Close) Unlocked JP16 - Infrared Connector Power Select JP16 Select (1-2) Powered by +5V (2-3)* Powered by +5V Stand by* JP17 - Speaker Out Select JP17 Select (1-2) To Outside Speaker (2-3)*...

  • Page 8: Memory Configuration

    Memory Configuration You can install DIMM memory in the motherboard DIMM sockets. The board has DIMM sockets arranged as banks 1, and 2. You can install DIMMs in any of the two banks, and use different size DIMMs in different banks. The BIOS detects the size and type of installed memory.

  • Page 9: Installing The Processor

    Installing the Processor For easy installation of the CPU, it is recommended that you remove all Cards in PCI slots first. • Unpack the CPU and identify the pin 1 corner of the CPU. • Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of the CPU socket is designated by a small triangle printed on the motherboard.

  • Page 10: Bios Setup

    BIOS SETUP This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM, which retains the setup information when the power is turned off. Starting Setup The Award BIOS is immediately activated when you turn on the computer.
  • Page 11 CMOS Setup Utility - Copyright (C) 1984-1999 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save & Exit Setup PnP/PCI Configurations Exit Without Saving CPU Speed Setting Esc : Quit...

  • Page 12: Standard Cmos Features

    Set Supervisor/ Changes, sets, or disables password. It allows you to limit User Password access to the system and the Setup Program. Save & Exit Saves value changes to CMOS and exits setup. Setup Exit Without Abandons all CMOS value changes and exits setup. Save Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories.
  • Page 13 Primary These categories identify the types of the two channels that Master/Primary have been installed in the computer. There are 45 predefined Slave/Secondary types and one user definable types in BIOS. Type 1 to Type 45 are Master/Secondary predefined. Type “user” is user-definable. Slave Press PgUp or PgDn to select a numbered hard disk type or type the number and press <Enter>.

  • Page 14: Advanced Bios Features

    Advanced BIOS Features This section allows you to configure your system for basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. Advanced Chipset Features The Chipset Features Setup option is used to change the values of the chipset registers.
  • Page 15 ENTER PASSWORD: Type the password, up to eight characters in length, and press<Enter>. The new password will clear the previously entered password from the CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and operate without a password.

  • Page 16: Flash Update Procedure

    Flash Update Procedure A program AWDFLASH.EXE is included in the utility diskette or CD. The user is recommended to follow the procedure below to update the flash BIOS. 1. Create a DOS-bootable floppy diskette. Copy the new BIOS file (just obtained or downloaded) and the utility program AWDFLASH.EXE to the diskette.

Table of Contents