1. Manuals
  2. Brands
  3. PC Partner Manuals
  4. Motherboard
  5. 35880301
  6. Technical reference booklet

PC Partner 35880301 Technical Reference Booklet

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-
REORIENT OR RELOCATE THE RECEIVING ANTENNA
-
INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
-
CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
-
CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result
in harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to
operate this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for errors
or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective owners.
Electronic Emission Notices
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 35880301 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for PC Partner 35880301

Summary of Contents for PC Partner 35880301

  • Page 1 Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 2: Table Of Contents

    Table of Contents HARDWARE CONFIGURATION .............. 3 Key Features ....................3 Motherboard Layout (Model Code No. - 35880301) ........5 Jumper Settings ..................6 CPU Type Selection - JP7 ..............6 CMOS Clear - JP4 .................. 6 Installation ....................7 Installing the Retention Mechanism ............

  • Page 3: Hardware Configuration

    HARDWARE CONFIGURATION The Pentium® II Baby AT motherboard is based on the Intel® 440EX or 440LX Chipset. The chipset is a highly integrated solution for a cost-effective and compact motherboard. The motherboard supports SDRAM and 3.3V EDO. Features on-board include super-I/O, Ultra DMA33, PCI bus master IDE, AGP Ver 1.0, PCI Ver 2.1 compliant, USB, VRM 8.1 compliant, ECC (440LX ver.
  • Page 4 • Support Bus Master IDE and PIO mode 4 (up to 16.7M bytes/sec) and Ultra DMA33 (up to 33M bytes/sec) transfer. • One ECP/EPP parallel port (via a header). • Two 16550 Compatible UART serial ports (via a header). • One floppy port, Supports two FDD of 360KB, 720KB, 1.2MB , 1.44MB and 2.88MB capacity.

  • Page 5: Motherboard Layout (Model Code No. - 35880301)

    Motherboard Layout (Model Code No. - 35880301) The following diagrams show the relative positions of the jumpers, connectors, major components and banks on the motherboard. Hardware Setup...

  • Page 6: Jumper Settings

    Jumper Settings This chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. CPU Type Selection - JP7 CPU Type and Speed Pentium II - 233MHz Pentium II - 266MHz* Pentium II - 300MHz...

  • Page 7: Installation

    Instalation Installing the Retention Mechanism To install the retention mechanism, follow these steps: 1. Locate Slot 1 and the four attachment studs on the motherboard. 2. To position the mechanism, orient it as shown in figure. The tab on the connector fits into a notch in the base of the mechanism.

  • Page 8: Installing The Dimms

    Installing the DIMMs 1. Turn off all peripheral devices connected to the computer. Turn off the computer. 2. Remove the computer cover and locate the DIMM sockets. 3. Holding the DIMM by the edges, remove it from its antistatic package. 4.

  • Page 9: Bios Setup

    BIOS SETUP This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM, which retains the setup information when the power is turned off.
  • Page 10 ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE. INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION SETUP HDD LOW LEVEL FORMAT LOAD BIOS DEFAULTS SAVE &...

  • Page 11: Standard Cmos Setup

    Supervisor / Changes, sets , or disables password. It allows you to limit access User Password to the system and the Setup Program. Setting IDE HDD Auto Automatically detects and configures the hard disk parameters. The Detection Award BIOS includes this ability in the event you are uncertain of your hard disk’s parameters.

  • Page 12: Bios Features Setup

    Primary These categories identify the types of the two channels that Master/Primary have been installed in the computer. There are 45 predefined types Slave/Secondary and four user definable types are BIOS. Type 1 to Type 45 are Master/Secondary predefined. Type “user” is user-definable. Slave Press PgUp or PgDn to select a numbered hard disk type or type the number and press <Enter>.

  • Page 13: Chipset Features Setup

    Chipset Features Setup The Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer. This section allows you to configure the system based on the specific features of the installed chipset.

  • Page 14: Power Management Setup

    The password requirement is defined by the Security Option of the BIOS Features Setup Menu. If the Security Option is set to “System”, the password will be required both at resetting and at entering setup . If the option is set to “Setup”, the prompt only appears when you try to enter setup.

  • Page 15: Flash Update Procedure

    Flash Update Procedure A program AWDFLASH.EXE is included in the utility diskette. The user is recommended to follow the procedure below to update the flash BIOS. 1. Create a DOS-bootable floppy diskette. Copy the new BIOS file (just obtained or downloaded) and the utility program AWDFLASH.EXE to the diskette.
  • Page 16 Technical Reference Booklet...

Table of Contents