Table of Contents
Advertisement
Quick Links
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-
REORIENT OR RELOCATE THE RECEIVING ANTENNA
-
INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
-
CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
-
CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result in
harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate
this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be
copied or reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility
for errors or omissions is assumed. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their
respective owners.
Electronic Emission Notices
SAPPHIRE PURE PERFORMANCE II
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PC Partner SAPPHIRE PURE PERFORMANCE II
Summary of Contents for PC Partner SAPPHIRE PURE PERFORMANCE II
- Page 1 Neither is any liability assumed for damages resulting from the use of the information contained herein. Trademarks All brand names, logos and registered trademarks mentioned are property of their respective owners. SAPPHIRE PURE PERFORMANCE II...
-
Page 2: Table Of Contents
TABLE OF CONTENTS HARDWARE CONFIGURATION ..............4 Key Features ....................4 MOTHERBOARD LAYOUT ................7 REAR PANEL ....................8 AUDIO CONFIGURATION ................10 SPEAKER CONFIGURATION ................ 10 Method 1: 2/4/6 Channel audio output on back panel only ....10 Method 2: Using S-Bracket connectors ..........12 CONNECTORS ..................... - Page 3 SATA RAID SETUP ..................40 Creating RAID Sets ................40 Deleting RAID Sets ................40 Resolving Conflict .................. 41 DRIVER AND RAID SOFTWARE INSTALLATION ........41 Microsoft Windows Driver Installation ........... 41 Install Windows2000/XP ................ 41 APPENDIX ....................42 SAPPHIRE PURE PERFORMANCE II...
-
Page 4: Hardware Configuration
HARDWARE CONFIGURATION Key Features Chipset • ATI® RS400+SB400 Chipset. Processor • Supports Intel® Celeron® , Pentium® 4 processors in the LGA775 -pin package (with 0.8V~1.6V voltage). • Supports 64-bit PSB (Processor System Bus) frequency of 400MHz/ 533MHz/800MHz (100MHz/133MHz/200MHz bus clock). VRM 10.0 (Voltage Regulator Modules) on Board •... - Page 5 IEEE 802.3X Full Duplex Flow Control. • Supports 10 Mb/s, 100 Mb/s and 1000 Mb/s operation. • Supports Wake-On-LAN function and remote wake-up. Onboard IEEE1394 • Compliant with 1394 open HCI specifications v1.0 and v1.1. • Integrated 400Mbit 2-port PHY. SAPPHIRE PURE PERFORMANCE II...
- Page 6 PCI Express Graphics Interface • One 16-lane (x16 port) PCI Express port intended for Graphics Attach, Fully compliant to the PCI Express Base Specification revision 1.0a. • A base PCI Express frequency of 2.5GB/s only. • PCI Express supports and Enhanced Addressing Mechanism. PCI Express x1 Port •...
-
Page 7: Motherboard Layout
When you start up the system, please wait for 5 seconds after you power on AC. It is not recommended to add a metal spacer plate on the back of the Socket775. Otherwise, some components will be short and damaged. SAPPHIRE PURE PERFORMANCE II... -
Page 8: Rear Panel
REAR PANEL The back panel provides the following connectors: PS/2 Mouse Connector The Sapphire motherboard provides a standard PS/2 mouse mini DIN ® connector for attaching a PS/2 mouse.You can plug a PS/2 mouse directly ® ® into this connector. PS/2 Keyboard Connector The Sapphire motherboard provides a standard PS/2 keyboard mini DIN... - Page 9 CD player, Tape player, or other audio devices. Mic In is a connector for microphones. The ALC650/655 embeds an internal analog switch (by driver software) to select LINE input or Surround output, and select MIC input or CENTER/ LFE output. SAPPHIRE PURE PERFORMANCE II...
-
Page 10: Audio Configuration
AUDIO CONFIGURATION After installing the audio driver, you can select 2/4/6 channel surround audio output in software utility and then connect surround speakers to appropriate audio ports. There are two ways to obtain 2/4/6 channel audio output: 2/4/6 channel audio output of back panel only. All surround speakers connect to audio connector. - Page 11 A. If you choose 4-channel mode for 4 speaker output, the selected item is shown as below (Figure1). (Figure1) B. If you choose 6-channel mode for 5.1 speaker output, the selected item is shown as below (Figure2). (Figure2) SAPPHIRE PURE PERFORMANCE II...
-
Page 12: Method 2: Using S-Bracket Connectors
Method 2: Using S-BRACKET connectors: S-Bracket (The S-Bracket is showed in page 15) is an optional accessory. It gives access to analog and digital audio output by integrating both SPDIF and analog LINE OUT connectors. To use the S-Bracket, you should select correct setting in the software utility. - Page 13 Line Out connectors of S-Bracket, or six speakers to the connector of S-Bracket. If you want to use Line In and MIC function at the same time, please click the Rear Speaker Out and Center/Subwoofer Speaker Out buttons. (shown below) SAPPHIRE PURE PERFORMANCE II...
-
Page 14: Connectors
CONNECTORS The Sapphire motherboard provides connectors to connect to FDD, IDE HDD, USB Ports and CPU/System FAN etc. Floppy Disk Drive Connector - CN3 The Sapphire motherboard provides a standard floppy disk drive connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. IDE Connectors - CN1, CN2 The Sapphire motherboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/ 66/100/133 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA... -
Page 15: Six Channel Audio Output Connector - J19
Audio left surrounding output SOUT-R Audio right surrounding output Ground Ground CET-OUT Audio center output LFE-OUT Audio bass output Ground SPK L Front left output SPK R Front right output S-Bracket Cable (optional) Connect to J19 SAPPHIRE PURE PERFORMANCE II... -
Page 16: Tv Out Header - J3
TV Out Header - J3 The Sapphire motherboard provides TV Out header. J3 - Pin Definition Assignment COMP/B TV Out cable PP-I7RS400 User’s Manual... -
Page 17: Ieee1394 Connector - J23
The Sapphire motherboard provides a 1394 pin header that allow you to connect IEEE 1394 ports. J23 - Pin Definition SIGNAL TPA+ TPA- Ground Ground TPB+ TPB- Cable power Cable power Key (no pin) Ground IEEE 1394 Cable (optional) SAPPHIRE PURE PERFORMANCE II... -
Page 18: Chassis Alarm Lead - Jp12
Chassis Alarm Lead: JP12(optional) This lead is for a chassis designed with intrusion detection feature.this requires an external detection mechanism such as a chassis intrusion sensor or microswitch.When you remove any chassis component,the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. JP12 JP12 - Pin Definition Assignment... -
Page 19: Fan Power Connectors - Cpufan1, Sysfan1
The green LED lights when the system is in the power-on state. The red LED lights whenever AC mains power is attached, irrespective of whether the system is power-on or power-off or standby mode. D55-5VSB_LED (Red) D54-VCC_LED (Green) SAPPHIRE PURE PERFORMANCE II... -
Page 20: Cd-In Header - J18
CD-IN Header - J18 This header allows for connection from the CD-ROM Drive. AUX-IN Header - J20 This header allows for connection from the Audio Device. J18 - Pin Definition Assignment CD-L CD-R J20 - Pin Definition Assignment AUX-L AUX-R PP-I7RS400 User’s Manual... -
Page 21: Front Panel Audio Header - Fp-S1
Also please make sure the pin assignment on the cable is the same as the pin assignment on the motherboard header. To find out if the chassis you are buying supports front audio connection, please contract your dealer. SAPPHIRE PURE PERFORMANCE II... -
Page 22: Usb Headers - Fp-U1, Fp-U2
USB Headers - FP-U1, FP-U2 This Sapphire motherboard has eight USB ports. Some computer cases have a special module that mounts USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector FP-U1, FP-U2 to connect the front mounted ports to the Sapphire mainboard. -
Page 23: Front Panel Header - Fp1
The Sapphire motherboard provides a front panel connection to the front panel switches and LEDs. FP1 is compliant with the Front Panel I/O Connectivity Design Guide. KEYLOCK SPEAKER IRRX IRTX RESET PWR_SW PW_LED- HDD_LED- PW_LED+ HDD_LED+ SAPPHIRE PURE PERFORMANCE II... -
Page 24: Serial Ata Hard Disk Connectors - Sata1/Sata2/Sata3/Sata4
Serial ATA Hard Disk Connectors - SATA1/SATA2/SATA3/SATA4 The Sapphire motherboard has four SATA connectors. Each supports generation SATA data rates of 150 MB/s. Both connectors are fully compliant with Serial ATA 1.0 specifications. Each SATA connector can connect to one hard disk device. Please refer to SATA Raid setup (Page 38) for detail software installation procedure. - Page 25 SATA Hard Disk. Please do not fold the serial ATA cable in a 90-degree angle, which will cause the loss of data during the transmission. Serial ATA Hard Disk Devices Power Cable (optional) SAPPHIRE PURE PERFORMANCE II...
-
Page 26: Jumper Setting
JUMPER SETTING The Sapphire motherboard provides jumpers enabling configuration of the hardware. Clear CMOS Jumper - JP9 If you want to clear the system configuration, use the JP9(Clear CMOS Jumper) to clear data. Selection 1-2* Normal* CMOS Clear Onboard AC97 Sound Select - JP2 Function 1-2* AC97 Sound Enable*... -
Page 27: Slots
• Two virtual channel support for full unsynchronized data transfers. • Supports full 2.5Gb/s bandwidth in each direction per x1 lane. PCI (Peripheral Component Interconnect) Slots • Five 32-bit PCI ports for add-in card connections. Slots SAPPHIRE PURE PERFORMANCE II... -
Page 28: Cpu Installation
CPU INSTALLATION Please refer to the following steps to install the CPU. 1.Please turn off the power and unplug the power cord before installing the CPU. Use index finger and thumb to raise the metal lever so it is separated from the bottom steel shell grip hook. - Page 29 CPU. This may also be done by removing the lid beforehand. 5.Press the metal lever so it is secured in the bottom steel shell grip hook. SAPPHIRE PURE PERFORMANCE II...
- Page 30 6. It is recommended that the CPU heatsink should be approved by Intel Corporation. Choose the orientation of the thermal solution for optimal wire routing to the fan header on the Sapphire motherboard. Position the thermal solution over the processor. Ensure the fan wiring is positioned to prevent wire pinching between the heatsink and the processor, or between the heatsink clip and the socket.
- Page 31 9. Gently rotate the cap clockwise 1/4 turn to fasten the heatsink onto the Sapphire motherboard. 10. Lastly, attach the fan wire connector to the 4 pin fan header connector Sapphire motherboard labeled CPU FAN. SAPPHIRE PURE PERFORMANCE II...
-
Page 32: Memory Configurations
MEMORY CONFIGURATIONS 1.DDR DIMM Sockets Location Please refer to the following figure for the location of the DDR DIMM Sockets. 2.Install DDR DIMMs Please follow the below mentioned steps to install DDR DIMMs. 1. Hold the DDR DIMM module by the edges and remove it from its antistatic package. -
Page 33: Memory Configurations
• In dual channel mode, always install an identical (the same type and size) DDR DIMM pair in sockets. • It is not recommended to use a three-DIMM configuration. • Memory channel speed is determined by the slowest DIMM populated in the system. SAPPHIRE PURE PERFORMANCE II... -
Page 34: Bios Setup
BIOS SETUP About the Setup Utility The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. -
Page 35: Main Menu
This entry only appears if your system supports Power Management Management “Green PC” standards. Setup PnP/PCI This entry appears if your system supports PnP/PCI. Configurations PC Health Status Display CPU and Case Fan Speed, temperature, etc. SAPPHIRE PURE PERFORMANCE II... -
Page 36: Standard Cmos Features
Load Fail-Safe The BIOS defaults have been set by Sapphire and represent Defaults settings which provide the minimum requirements for your system to operate. Load Optimized The chipset defaults are settings which provide for maximum Defaults system performance. Sapphire has assigned these values to provide optimized performance. -
Page 37: Advanced Bios Features
This section describes how to configure the PCI bus system. This section covers some very technical items and it is recommended that only experienced users should make any changes to the default settings. PC Health Status The PC Health Status display CPU and Case Fan Speed. SAPPHIRE PURE PERFORMANCE II... -
Page 38: Set Supervisor/User Password
Set Supervisor/User Password When this function is selected, the following message appears at the center of the screen to assist you in creating a password. ENTER PASSWORD Type the password, up to eight characters, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. -
Page 39: Bios Update Procedure
Do not turn off or RESET the computer during the flash process. If you are unsure how to upgrade the BIOS, it is best to take your computer to an Authorized Service Center and have a trained technician do the work for you. SAPPHIRE PURE PERFORMANCE II... -
Page 40: Sata Raid Setup
SATA RAID SETUP Creating and deleting RAID sets is a function found in the RAID utility. During bootup, the following message will appear, pausing for a few seconds to allow the user to enter the RAID utility: Press Ctrl+S or F4 to enter RAID utility An easy-to-use screen will appear with the following choices: Create RAID Set Delete RAID Set Rebuild RAID Set Resolve Conflicts Below this will be a list of drives currently installed on the system. -
Page 41: Resolving Conflict
3. Press “F6” when display “Press F6 if you need to install a third party SCSI or RAID driver...” 4. Insert floppy disk. 5. Choose the OS device driver wanted for loading. 6. Install OS. 7. Install driver after OS is installed. SAPPHIRE PURE PERFORMANCE II... -
Page 42: Appendix
APPENDIX Note to User: The bundled driver CD attached an Auto-Run feature for all the drivers that the Sapphire motherboard needs. Please select the drivers that you want to install and click the button on the installation panel. PP-I7RS400 User’s Manual... - Page 43 SAPPHIRE PURE PERFORMANCE II...
- Page 44 PP-I7RS400 User’s Manual FC1117A8...
Need help?
Do you have a question about the SAPPHIRE PURE PERFORMANCE II and is the answer not in the manual?
Questions and answers