Sealey S01046.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
Maintain the sander in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
9
Before each use check abrasive belt for condition. If worn or damaged replace immediately.
9
Use only the correct size and type of sanding belt with this sander.
9
Ensure there are no flammable or combustible materials near the work area.
9
WARNING! Always wear approved eye or face and hand protection when operating the sander.
‰
Use face, dust, or respiratory protection in accordance with COSHH regulations.
9
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
Ensure work piece is secure before operating the sander. Never hold a work piece by hand.
9
Check the work piece to ensure there are no protruding screws, bolts, nuts, nails, rivets, etc.
9
Avoid unintentional starting.
9
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Prolonged exposure to vibration from this sander poses a health risk. It is the owner's responsibility to correctly assess the potential
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
8
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WARNING! DO NOT sand any materials containing asbestos.
‰
DO NOT carry the sander by the hose, or yank the hose from the air supply.
8
DO NOT force, or apply heavy pressure to, the sander, let the sander do the work.
8
DO NOT switch the sander on whilst the belt is in contact with the work piece.
8
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping/cleaning rags etc.
8
DO NOT carry the sander with your finger on the power lever.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
1.2. HAND ARM VIBRATION
WARNING! – RISK OF HAND ARM VIBRATION INJURY
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 1.1m/s²
Uncertainty value (k): 0.13m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
© Jack Sealey Limited
AIR BELT SANDER
S01046.V2
MODEL NO:
Wear ear Wear protective
protection gloves
Original Language Version
Wear a mask Warning
S01046.V2 Issue 2 (H,1,2,3,F) 04/10/23