Table of Contents

Advertisement

Quick Links

Operation & Maintenance Manual
AlphaBlower
Model 24-84-H & 24-84-P
!
REMEMBER:
Register your product! No claims for warranty shall be considered unless your product
registration card is completed online within 30 days of purchase. Go to: snowwolfplows.com/registration.
2023 Rev 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AlphaBlower 24-84-H and is the answer not in the manual?

Questions and answers

Summary of Contents for SnowWolf AlphaBlower 24-84-H

  • Page 1 Operation & Maintenance Manual AlphaBlower Model 24-84-H & 24-84-P REMEMBER: Register your product! No claims for warranty shall be considered unless your product registration card is completed online within 30 days of purchase. Go to: snowwolfplows.com/registration. 2023 Rev 1...
  • Page 2 SNOWWOLF factory or authorized SNOWWOLF dealership or in any way so as in SNOWWOLF'S judgment, to affect its stability or reliability, nor which has been subject to misuse, negligence or accident beyond the Company recommended machine rated capacity.
  • Page 3: Table Of Contents

    CONTENTS Introduction ............................3 Owner Information .............3 Serial Number Location .
  • Page 4 Maintenance Schedule ............32 Lubrication .
  • Page 5: Introduction

    SnowWolf is continually working to improve its specific service operation. products. SnowWolf reserves the right to make any improvements or changes as deemed...
  • Page 6: Alphablower Identification

    Introduction AlphaBlower Identification DEFLECTOR CHUTE DRIFT CUTTER DRIFT CUTTER GEARBOX RUBBER FLAP CUTTING EDGE AUGER RIGHT SIDE AUGER CUTTING EDGE AlphaBlower Operation and Maintenance Manual...
  • Page 7 Introduction AlphaBlower Identification (Cont’d) DEFLECTOR CYLINDER LIFTING POINT MANIFOLD IMPELLER HOUSING AUGER WEAR SHOE AlphaBlower Operation and Maintenance Manual...
  • Page 8 AlphaBlower Operation and Maintenance Manual...
  • Page 9: Safety

    Safety Safety Information Safe Operation Needs A Qualified Operator Safety Alert Symbol This SAFETY ALERT SYMBOL identifies important safety messages AVOID SERIOUS INJURY OR DEATH equipment and in the owner’s manual. When you see this symbol, be alert to the Operators must receive instructions before possibility of personal injury and carefully operating the machine.
  • Page 10: Importance Of Safety

    • Always stop the snow blower if any persons your authorized Distributor, Dealer Parts enter the work area. Department or SnowWolf for safety decal replacement. • DO NOT modify the snow blower in any way. Unauthorized modification may impair the •...
  • Page 11 Safety Importance of Safety Cont’d Hydraulic Safety • Always disconnect hydraulic connections Fire Prevention Safety between the machine and the snow blower before performing maintenance to the snow • All fuels, most lubricants and some coolant blower. mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto •...
  • Page 12 AlphaBlower Operation and Maintenance Manual...
  • Page 13: Operation

    Operation General Information Pre-Operation Inspection Snow Blower Operating Tips Before operating the snow blower for the first time • Make sure the snow blower is adjusted and each time thereafter, use the following list as properly. (See “AlphaBlower Adjustment Skid a guideline during equipment inspection.
  • Page 14: Alphablower Inspection

    Operation AlphaBlower Inspection Monthly Inspection Check the following items every 50 hours of Daily Inspection operation: • Inspect the snow blower, frame, and all welds NOTE: Inspect the snow blower by performing for cracks, bends, or excessive wear. a walk around daily before and after use.
  • Page 15: Tractor Requirements

    Operation Tractor Requirements Entering and Exiting the Machine REQUIREMENTS Entering The Operator’s Position Power Input (min/max) 60- 150 HP Hitch Type Cat 2, 3 or 4 Use the machine’s safety treads, handles and steps to enter the operator’s position. PTO Revolutions When in the operator’s position, fasten the seat NOTE: It is important to use the correct type of belt, start the engine and release the parking...
  • Page 16: Alphablower Installation Skid Steer

    Operation AlphaBlower Installation Skid Steer Connecting The Snow Blower To A Once connected to the universal plate and secure, shut down machine and exit operators position. Skid Steer Hook up the 3 couplers Be sure the case drain is installed properly as this could cause catastrophic failure of the hydraulic motor.
  • Page 17: Alphablower Adjustment Skid Steer

    Operation AlphaBlower Adjustment Skid Steer The snow blower must be adjusted so that it is level. INCORRECT INCORRECT CORRECT NOTE: The blower should now be resting on For the blower to penetrate all the way down to the cutting edge. the asphalt it is very important that the blower is correctly adjusted to be level prior to operation.
  • Page 18: Alphablower Installation To Tractor

    Operation AlphaBlower Installation Connecting The Snow Blower To The Tractor’s Three-Point Hitch To Tractor NOTE: Ensure that the PTO shaft guard is always in place, that it is in proper condition and secured using the supplied chain to prevent rotation during use. Figure 1 CRUSH HAZARD •...
  • Page 19 Operation Connecting The Snow Blower To The Tractor’s Three-Point Hitch (Cont’d) NOTE: Tractor hitch type may require a different procedure installation. (See tractor’s operation manual for the correct procedure.) Exit the operator’s position. (See “Entering The Operator’s Position” on page 13.) Close the tractor’s three-point hitch locking levers (if equipped).
  • Page 20: Pto Installation

    Operation PTO Installation 7. Install the axle and check the adaptation carefully and at all heights and movements. Install the PTO shaft from the blower to the tractor. The angle of the PTO should not exceed 20 degrees. Angles greater than 20 degrees result in excessive wear and reduce service life of PTO shafts.
  • Page 21 Operation Figure 2 PTO SHAFT ANGLE - REVERSING 2.25” 20° 15.75” 15° 2” 10° 5° 2” 20.5” 23.5” 11.75” 11.75” 19.5” 14.25” PTO SHAFT ANGLE - FRONT MOUNTING 2.25” 20° 15° 15.75” 2” 5° 10° 2” 7” 23.5” 11.75” 11.75” 23.5”...
  • Page 22: Alphablower Adjustment Tractor

    Operation AlphaBlower Adjustment Tractor The snow blower must be adjusted so that it is level. INCORRECT INCORRECT CORRECT For the blower to penetrate all the way down to 1. Locate a level surface to adjust the blower. the asphalt it is very important that the blower is 2.
  • Page 23 Operation AlphaBlower Adjustment Tractor (Cont’d) 6. Adjust wear shoes / gauge wheels so that these are flush with the surface.Then tighten the adjustment bolt slightly more so that the wear shoes / gauge wheels are pushed down against the surface. 7.
  • Page 24: Hydraulic Couplers

    Operation Hydraulic Couplers • Thoroughly clean the quick couplers before making connections. Dirt can quickly damage the hydraulic system. AVOID BURNS Hydraulic fluid, fluid tubes, fittings and quick couplers can when running machine and snow blower. careful when connecting disconnecting quick couplers. Connecting Hydraulic Couplers: Remove any dirt or debris from the surface of both the male and female couplers, and from the...
  • Page 25: Checking Alphablower Operation

    Operation Checking AlphaBlower Engage the machine’s auxiliary hydraulics. (See the machine’s operation manual for correct Operation procedure.) Auger Rotation NOTE: After installing the snow blower, test all Start auger rotation. functions before operating the snow Raise the engine RPM. blower in the work area. Allow the snow blower auger to rotate for a short time (approximately one minute).
  • Page 26: Operating The Alphablower

    Operation Operating The AlphaBlower Operation Start the engine and release the parking brake. Raise the snow blower slightly off the ground. Move to the work area. Engage the machine’s auxiliary hydraulics. (See AVOID INJURY OR DEATH the machine’s Operation Manual for correct While operating the machine: procedure.) •...
  • Page 27: Clearing A Plugged Alphablower

    Operation Clearing a Plugged AlphaBlower AVOID SERIOUS INJURY OR DEATH If the auger / chute becomes clogged with snow, turn the machine’s engine off. Use a clearing rod, never insert hands or feet into the chute or auger opening. NOTE: If the AlphaBlower is equipped with the hydraulic tip down option the chute can be tilted down to remove snow from the impeller housing.
  • Page 28: Alphablower Removal Skid Steer

    Operation AlphaBlower Removal Skid Steer AVOID BURNS NOTE: Put the snow blower on planks or Hydraulic fluid, tubes, fittings and quick blocks before removing it from the couplers can get hot during operation. Be machine to prevent it from settling or careful when connecting and disconnecting sinking in soft / wet ground.
  • Page 29: Alphablower Removal Tractor

    Operation AlphaBlower Removal Tractor NOTE: When the connection frame has been installed for towing, the support jack AVOID BURNS must always be installed before the Hydraulic fluid, tubes, fittings and quick snow blower is disconnected from the couplers can get hot during operation. Be machine.
  • Page 30 AlphaBlower Operation and Maintenance Manual...
  • Page 31: Maintenance

    SnowWolf will auxiliary hydraulic hose quick couplers responsible for injuries or damage caused by from the skid steer before performing use of unapproved parts and / or accessories.
  • Page 32: General Maintenance

    Maintenance General Maintenance NOTE: After initial use, or repair/replacement of damaged parts, it is important to check the repaired or replaced parts for proper bolt torque, operation and leaks. AVOID SERIOUS INJURY OR DEATH Before operating or servicing system: Read and understand the machine’s owners manual.
  • Page 33: Alphablower Maintenance

    Maintenance AlphaBlower Maintenance AVOID SERIOUS INJURY OR DEATH Always turn off and lockout power on the machine before servicing the snow blower. AVOID SERIOUS INJURY OR DEATH Always disconnect hydraulic connections between the snow blower and the machine before performing any type of maintenance to the snow blower.
  • Page 34: Maintenance Schedule

    Maintenance Maintenance Schedule SERVICE PROCEDURES DESCRIPTION Daily Maintenance (or every 10 hrs) Check Grease Oil Lube Change Wear Shoe Gauge Wheel Weekly Maintenance (or every 40 hrs) PTO Shaft Axle Ball Bearings Chute Fixing Bolts Check Hydraulic Hoses Snow Blower Frame Hardware Monthly Maintenance (or every 170 hrs) Auger Bearings...
  • Page 35: Lubrication

    Maintenance Lubrication Blower Grease Points Figure 2 PTO Shaft Figure 1 Grease the PTO shaft fittings (Item 1), bearing for the guard (Item 2) and telescoping tubes (Item 3) [Figure 1] every 40 hours of operation. NOTE: For lubrication of the telescoping tubes (Item 3) the PTO shaft must be pulled The snow blower is equipped with three ball apart.
  • Page 36: Oil Change On The Cut Out Clutch

    Maintenance Lubrication (Cont’d) Gearbox Oil Change for Front Mounted Units Follow the same procedure above for the front Gearbox Oil Change mounted gearbox. Figure 3 PTO Gearbox Oil PTO gearbox, L30-030: 1,4 liters gear oil, Mobil SHC Gear 220. (models: 24-84-PA, 24-84- Oil Change on the Cut Out Clutch Change the oil for the cut out clutch every 500 hours or at least once per year.
  • Page 37: Auger Axle Couplings

    Maintenance Auger Axle Couplings Hydraulic Hoses Check the couplings between the gearbox and the Check that there is no damage to hydraulic hoses. auger axle for wear. If there is significant wear, the Replace any damaged hoses. Also check for any bushings in the coupling must be replaced.
  • Page 38: Cutting Edge Replacement

    Cutting Edge Replacement NOTE: Replace or flip the bolt-on cutting edge when it wears within 1/2” - 3/4”. Replace only with genuine SnowWolf cutting edge and hardware. 1. Park the machine on a level surface with the snow blower properly attached.
  • Page 39: Troubleshooting

    Maintenance Troubleshooting 24-84-P PROBLEM CAUSE SOLUTION Snow Blower not adjusted Adjust the snow blower. properly. Snow blower leaving snow behind. Replace cutting edge / wing Cutting edge worn or damaged. cutting edges. Gearbox faulty. Repair or replace. Bolt in PTO shaft sheared. Replace bolt.
  • Page 40: Storage And Return To Service

    Maintenance Storage And Return To Service Storage Return to Service After the seasons use or when the snow blower After the snow blower has been in storage, it is will not be in use for a period of time, perform the necessary to follow a list of items to return the following steps.
  • Page 41: Parts

    Parts This page left intentionally blank AlphaBlower Operation and Maintenance Manual...
  • Page 42: Alphablower

    Parts AlphaBlower AlphaBlower Parts AlphaBlower Operation and Maintenance Manual...
  • Page 43 Parts ITEM PART # DESCRIPTION 1900-010 Standard Chute w/ HYD 4 Flaps Snow Blower, 540 rpm Snow Blower, 1000 rpm 2014-400TP Connection Frame, 3-Point 0990-300 Cylinder, Hydraulic Tilt 0994 Chute, Telescopic (Optional) 2006-550 Swivel Stopper 2011-560H Drift Cutter, Right 2011-560V Drift Cutter, Left 10, 11 2012-550...
  • Page 44: Chute

    Parts Chute AlphaBlower Operation and Maintenance Manual...
  • Page 45 Parts ITEM PART # DESCRIPTION 2116-711 Chute, Bottom Plate 2116-712 Chute, Body 2116-713 Lower Flap 2116-714 Upper Flap 2116-716 Support Plate 2116-742 Parallel Rod 2116-744 Wear Plate, Hardox F102-08050 Hexagon Screw, M8 x 50 F102-12020 Hexagon Screw, M12 x 20 F102-12030 Hexagon Screw, M12 x 30 F102-16035...
  • Page 46: Deluxe Chute, 4-Stage

    Parts Deluxe Chute, 4-Stage See Chute, Hydraulic Tilt on page Detail A AlphaBlower Operation and Maintenance Manual...
  • Page 47 Parts ITEM PART # DESCRIPTION 0991-016 BOLT, HEX, M24 1900-040 FLAP 4 1900-045 FLAP 3 1900-050 FLAP 2 1900-055 FLAP 1 1900-073 1900-075 CHUTE 1900-079 SLEEVE 1900-080 CHUTE ATTACHMENT 1900-085 SLEEVE 1900-086 SLEEVE 1900-090 GUARD 1900-140 SLEEVE 1900-208 HOSE, HYDRAULIC 1900-210 HOSE, HYDRAULIC 1900-212...
  • Page 48: Chute, Telescopic (Optional)

    Parts Chute, Telescopic (Optional) Detail E Detail A Detail C Detail B Detail D AlphaBlower Operation and Maintenance Manual...
  • Page 49 Parts ITEM PART # DESCRIPTION 0994-003 BOLT 0994-020 LOADING SECTION, LOWER 0994-040 BRACKET, SLIDING 0994-050 HATCH 0994-060 ARM, LOCKING 0994-100 LOADING SECTION, UPPER 0994-150 DEFLECTOR, ADJUSTABLE 0994-160 BRACKET P81061 HOSE, 1/4 x 118", 4800PSI, #4FJIC-#4FJIC P81060 HOSE, 1/4 x 176", 4800PSI, #4FJIC-#4FJIC P81059 HOSE, 1/4 x 183", 4800PSI, #4FJIC-#4FJIC P81056...
  • Page 50: Blower Parts

    Parts Blower Parts ITEM PART # DESCRIPTION 2116-100 Blower Housing, Welded 2116-350VB Auger Left 2116-350HB Auger Right (not shown) 2116-561H Drift Cutting Edge Right 2116-561V Drift Cutting Edge Left 2116-562H Support Right 2116-562V Support Left F102-12030 Bolt, Hex, M12 x 30 F112-12030 Bolt, Carriage, M12 x 30 F312-12...
  • Page 51: Hydraulic Swivel Motor

    Parts Hydraulic Swivel Motor ITEM PART # DESCRIPTION 2116-805 HYDRAULIC SWIVEL MOTOR 0984-301C COG WHEEL P81058 HOSE, HYDRAULIC 2116-758 COVER 0984-604 SLEEVE, SPACER 2116-757 ENGINE SUPPORT SLEW RING F102-08025 BOLT, HEX, M8 x 25 F102-12100 BOLT, HEX, M12 x 100 F312-12 NUT, LOCK, M12 F402-08...
  • Page 52: Hydraulic Swivel Motor Assembly

    Parts Hydraulic Swivel Motor Assembly ITEM PART # DESCRIPTION 0984-510 Slew Ring Ø500 toothed 2116-144B Support Bracket 2116-805 Hydraulic Swivel Motor F102-08025 Bolt, Hex, M8 x 25 F102-12035 Bolt, Hex, M12 x 35 F102-12045 Bolt, Hex, M12 x 45 F312-08 Nut, Lock, M8 F312-12 Nut, Lock, M12...
  • Page 53: Chute, Hydraulic Tilt

    Parts Chute, Hydraulic Tilt 33-106-P ITEM PART # DESCRIPTION 1900-200 Hose, Hydraulic 1900-205 Hose, Hydraulic 1900-206 Hose, Hydraulic F102-06080 Bolt, Hex F312-06 Nut, Locking F430-16 Retaining Ring F611-027 Clamp, Double G01-076 Nipple G01-080 Nipple G01-091 T-nipple G50-062 Gasket, Steel / Rubber H05-011 Cylinder, Hydraulic K05-008...
  • Page 54: Chute, Swivel Stopper

    Parts Chute, Swivel Stopper ITEM PART # DESCRIPTION 0984-551 Bracket 0984-552 Bracket F102-10035 Bolt, Hex, M10 x 35 F169-12030 Bolt, Socket Head, M12 x30 F302-06 Nut, Hex, M6 F312-10 Nut, Locking, M10 F402-10 Washer, Seating, 10.5 DIN125 F420-12 Washer, Seating, B12 K08-023 Rubber Damper AlphaBlower Operation and Maintenance Manual...
  • Page 55: Blower Fan

    Parts Blower Fan ITEM PART # DESCRIPTION 2116-300 Fan, Welded 2116-320 Bearing House, Welded F102-12030 Bolt, Hex, M12 x 30 F112-12045 Bolt, Carriage, M12 x 45 - 8.8 F312-12 Nut, Locking, M12 AlphaBlower Operation and Maintenance Manual...
  • Page 56: Gearbox Mounting

    Parts Gearbox Mounting ITEM PART # DESCRIPTION 2116-340 Gear Box, Mounted 2116-256 Gear Box, Guard 2116-020B Gear Box Mount, Welded F102-16035 Bolt, Hex, M16 x 35 F422-16 Washer, Locking, 16 mm Nordlock F102-10020 Bolt, Hex, M10 x 20 F402-10 Seating Washer, 10,5 DIN125 R91-081 Sticker, “Read the User Manual”...
  • Page 57: Blower Housing / Wear Shoes

    Parts Blower Housing / Wear Shoes ITEM PART # DESCRIPTION 2116-211 Axle 2116-215 Wear Shoes, Mounted 2116-219 Plate, Fixing 2116-250H Wear Shoe, Right 2116-250V Wear Shoe, Left (not shown) 2116-320 Bearing, Housing 2116-350HB Auger, Right 2116-350VB Auger, Left (not shown) F102-10035 Bolt, Hex, M10 x 35 F112-12045...
  • Page 58: Rubber Flap Parts

    Parts Rubber Flap Parts ITEM PART # DESCRIPTION 2116-553 Rubber Flap 2116-554 Clamping Plate F102-10025 Bolt, Hex, M10 x 25 F312-10 Nut, Locking, M10 AlphaBlower Operation and Maintenance Manual...
  • Page 59: Auger Axle Parts

    Parts Auger Axle Parts ITEM PART # DESCRIPTION 2116-254 Bracket 2116-253 Bearing, Guard K02-003 Flanged Bearing, UCF210 F102-16050 Bolt, Hex, M16 x 50 F402-17 Seating, Washer, 17 F312-16 Nut, Locking, M16 F173-12030A Bolt, Socket, Flat Head, M12 x 30 F312-12 Nut, Locking, M12 F430-50 Retaining Ring, A50x2...
  • Page 60: Cutting Edge / Axle Parts

    Parts Cutting Edge / Axle Parts ITEM PART # DESCRIPTION 2110-501 Cutting Edge, 2116-250V Wear Shoe, Left 2116-250H Wear Shoe Right, (not shown) F102-10035 Bolt, Hex, M10 x 35 F102-16035 Bolt, Hex, M16 x 35 F113-16050 Bolt, Carriage, M16 X 50 -10.9 F312-10 Nut, Lock, M10 F312-16...
  • Page 61: Gearbox

    Parts Gearbox ITEM PART # DESCRIPTION 2116-340 Gearbox 2116-341 Adapter 2116-358 Auger Attachment F169-10030 Bolt, Socket Head, 12.9 M10 x 30 F173-10030 Bolt, Socket Head, 10,9 M10 x 30 K99-022 Greasing Zerk, Straight M6 L01-344 EHTC 10/21 L L30-029 Gearbox, 9400A 3:1 AlphaBlower Operation and Maintenance Manual...
  • Page 62: Fan Axle Parts

    Parts Fan Axle Parts ITEM PART # DESCRIPTION 2116-138 Supporting Ring, Inner 2116-139 Supporting Ring 2116-304B Fan Axle 2116-321 Bearing Housing, Welded F430-50 Retaining Ring, A50 x 2 F435-90 Retaining Ring, I - 90 x 2.5 G01-017 Plug 3/8” R w/flange, DIN910 G50-057 Steel / Rubber Gasket for 3/8"BSP G53-5004...
  • Page 63: Wear Shoe

    Parts Wear Shoe ITEM PART # DESCRIPTION 2116-213 Sleeve w/bearing 2116-214 Bracket, Welded 2116-260 Support Disc F102-12065 Bolt, Hex, M12 x 65 F102-20075 Bolt, Hex, M20 x 75 F312-12 Nut, Locking, M12 F312-20 Nut, Locking, M20 AlphaBlower Operation and Maintenance Manual...
  • Page 64: Blower Skidsteer Mount

    Parts Blower Skidsteer Mount AlphaBlower Operation and Maintenance Manual...
  • Page 65 Parts ITEM PART # DESCRIPTION P81000 BLOWER SKIDSTEER MOUNT P20028 NUT, LOCK, 3/4”-10 GRADE C, STOVER P60230 BOLT, HEX, 3/4 x 3-1/2” YELLOW ZINC, GR8 P60296 WASHER, 3/4” SAE, GR8 P81100 ADJUSTER PIVOT PLATE FOR MOUNT ON 24-84 P81102 THRUST WASHER, SS BLOWER P81104 BOLT, HEX, 3/4-10 x 7”...
  • Page 66: Hydraulic Manifold, Motor

    Parts Hydraulic Manifold, Motor AlphaBlower Operation and Maintenance Manual...
  • Page 67 Parts ITEM PART # DESCRIPTION P30118 Manifold Assembly With Fittings (includes items 1-8) P38232 Cartridge, Check Valve P38229 Cartridge, Relief Valve Differential 100-1500 PSI Plug, SAE-8 Hex Head P38228 Spool Valve, (Torque to 70 FT. LBS) P38231 Coil, P Series, 12 VDC, Deutsch P38230 Cartridge, Solenoid, 4W3P Tandem Center Plug, SAE-6, Hex Head...
  • Page 68: Decal Identification

    DECAL, GREASE POINT DC125 DECAL, CAUTION HYDRAULICS DC124 DECAL, READ MANUAL DC126 DECAL, STAY CLEAR DC123 DECAL, CRUSH HAZARD DC127 DECAL, 3 in 1 WARNING DC28 DECAL, SNOWWOLF DC29 DECAL, WOLHEAD SWSN DECAL, SERIAL # 24-84-H 24-84-P AlphaBlower Operation and Maintenance Manual...
  • Page 69: Specifications

    Specifications AlphaBlower Specifications DESCRIPTION INCH (MM) Overall Height (A) 81” (2050 mm) Overall Length (B) 58” (1480 mm) Overall Width (C) 91” (2300 mm) Cutting Width (D) 87” (2200 mm) Cutting Height Without Upper Cutting Edge (E) 37” (940 mm) Cutting Height With Upper Cutting Edge (F) 57”...
  • Page 70: Torque Specifications

    Specifications Torque Specifications Standard Hardware And Lock Nuts BOLT SAE GRADE 5 SAE GRADE 8 LOCK NUTS TYPE Nominal Plated or Plated W / Plated or Plated W / Plated or Plated W / Size Unplated ZnCr Unplated ZnCr Unplated ZnCr W / Grade W / Grade...
  • Page 72 15100 Business Parkway, Rosemount, MN 55068 1-800-905-2265 snowwolfplows.com © 2023 SnowWolf...

This manual is also suitable for:

Alphablower 24-84-p

Table of Contents