1. Manuals
  2. Brands
  3. SnowWolf Manuals
  4. Snow Blower
  5. AlphaBlower 33-100-P
  6. Operation & maintenance manual

SnowWolf AlphaBlower 33-100-P Operation & Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operation & Maintenance Manual
AlphaBlower
Models 33-100-P & 33-100-H
!
REMEMBER:
Register your product! No claims for warranty shall be considered unless your product
registration card is completed online within 30 days of purchase. Go to: snowwolfplows.com/registration.
10-2021

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AlphaBlower 33-100-P and is the answer not in the manual?

Questions and answers

Related Manuals for SnowWolf AlphaBlower 33-100-P

Summary of Contents for SnowWolf AlphaBlower 33-100-P

  • Page 1 Operation & Maintenance Manual AlphaBlower Models 33-100-P & 33-100-H REMEMBER: Register your product! No claims for warranty shall be considered unless your product registration card is completed online within 30 days of purchase. Go to: snowwolfplows.com/registration. 10-2021...
  • Page 2 SNOWWOLF factory or authorized SNOWWOLF dealership or in any way so as in SNOWWOLF'S judgment, to affect its stability or reliability, nor which has been subject to misuse, negligence or accident beyond the Company recommended machine rated capacity.

  • Page 3: Table Of Contents

    Introduction ............................5 Owner Information .............7 Serial Number Location .
  • Page 4 Maintenance ............................37 Maintenance Safety ............39 General Maintenance .
  • Page 5 Options (Model 33-100-P) ........... . .86 Gearbox, Front Mounting .
  • Page 6 AlphaBlower Operation and Maintenance Manual...

  • Page 7: Introduction

    Introduction Owner Information ..............7 Serial Number Location .
  • Page 8 AlphaBlower Operation and Maintenance Manual...

  • Page 9: Owner Information

    SnowWolf is continually working to improve its NOTE: This document and the information products. SnowWolf reserves the right to make provided are the property of SnowWolf...

  • Page 10: Alphablower Identification (Model 33-100-P Shown)

    Introduction AlphaBlower Identification (Model 33-100-P Shown) DEFLECTOR DRIFT CUTTER (OPTIONAL) CHUTE DEFLECTOR DRIFT CUTTER CYLINDER (OPTIONAL) BLOWER HOUSING AUGER AUGER CUTTING CUTTING EDGE EDGE RIGHT SIDE AlphaBlower Operation and Maintenance Manual...
  • Page 11 Introduction AlphaBlower Identification (Model 33-100-P Shown) (Cont’d) TELESCOPIC CHUTE (OPTIONAL) LIFTING POINT CONNECTION FRAME FOR TOWING GAUGE WHEEL (OPTIONAL) CHUTE SWIVEL MOTOR THREE-POINT CONNECTION FRAME WEAR SHOE IMPELLER WEAR SHOE AlphaBlower Operation and Maintenance Manual...

  • Page 12: Standard Items

    Introduction The AlphaBlower two models are the 33-100-P Options (PTO Drive) or the 33-100-H (Hydraulic Drive). • Side Panels (Left or Right) The 33-100 is supplied for towing and reversing • Telescopic Loading Chute as standard. • Swivel Stopper for Chute The rotation direction of the impeller is such that the blower can be installed for reversing without •...

  • Page 13: Safety

    Safety Safety Information ............. . .13 Safe Operation Needs A Qualified Operator .
  • Page 14 AlphaBlower Operation and Maintenance Manual...

  • Page 15: Safety Information

    Safety Safety Information Safe Operation Needs A Qualified Operator Safety Alert Symbol This SAFETY ALERT SYMBOL identifies important safety messages AVOID SERIOUS INJURY OR DEATH equipment and in the owner’s manual. When you see this symbol, be alert to the Operators must receive instructions before possibility of personal injury and carefully operating the machine.

  • Page 16: Importance Of Safety

    Distributor, Dealer Parts • DO NOT modify the snow blower in any way. Department or SnowWolf for safety decal Unauthorized modification may impair the replacement. function and / or safety and could affect the life •...
  • Page 17 Safety Importance of Safety Cont’d Hydraulic Safety • Always disconnect hydraulic connections Fire Prevention Safety between the machine and the snow blower before performing maintenance to the snow • All fuels, most lubricants and some coolant blower. mixtures are flammable. Flammable fluids that are leaking or spilled onto hot surfaces or onto •...
  • Page 18 AlphaBlower Operation and Maintenance Manual...

  • Page 19: Operation

    Operation General Information ............. .19 Pre-Operation Inspection .
  • Page 20 AlphaBlower Operation and Maintenance Manual...

  • Page 21: General Information

    Operation General Information Snow Blower Operating Tips • Make sure the snow blower is adjusted Pre-Operation Inspection properly. (See “AlphaBlower Adjustment” on page 29.) Before operating the snow blower for the first time NOTE: Improper snow blower adjustment will and each time thereafter, use the following list as cause increased wear to the cutting a guideline during equipment inspection.

  • Page 22: Wireless Controls 33-100-H

    Operation Wireless Controls Synchronizing Transmitter and Receiver 33-100-H Each transmitter and receiver pair is synchronized together at the factory. If a new transmitter is NOTE: Wireless controls operate the 33-100-H needed, synchronizing is required. Use the only. following procedure: Operation 1.
  • Page 23 Operation 6. Press button that corresponds to OFF until 17. To engage the e-stop functionality, press green LED goes on, then off. This can be the button 2 until the green LED goes on, then off. same button that turns the output on. In this 18.

  • Page 24: Sleep Time

    Operation Sleep Time All transmitters have the ability to change the sleep time from the default to user's preference. The transmitter is factory set to turn off (sleep) after 15 minutes. To change the time the transmitter waits before going to sleep, use the following procedure: 1.

  • Page 25: Alphablower Inspection

    Operation AlphaBlower Inspection Monthly Inspection Check the following items every 50 hours of Daily Inspection operation: • Inspect the snow blower for cracks, bends, or NOTE: Inspect the snow blower by performing excessive wear. a walk around daily before and after use.

  • Page 26: Tractor Requirements

    Operation Tractor Requirements Entering and Exiting the Machine REQUIREMENTS Entering The Operator’s Position Power Input (min/max) 130 - 250 HP Hitch Type Cat 2, 3 or 4 Use the machine’s safety treads, handles and steps to enter the operator’s position. PTO Revolutions When in the operator’s position, fasten the seat belt, start the engine and release the parking...

  • Page 27: Alphablower Installation

    Operation AlphaBlower Installation Connecting The Snow Blower To The Tractor’s Three-Point Hitch NOTE: Ensure that the PTO shaft guard is always in place, that it is in proper condition and secured using the supplied chain to prevent rotation during use. Figure 1 CRUSH HAZARD •...
  • Page 28 Operation Connecting The Snow Blower To The Tractor’s Three-Point Hitch (Cont’d) NOTE: Tractor hitch type may require a different procedure installation. (See tractor’s operation manual for the correct procedure.) Exit the operator’s position. (See “Exiting The Operator’s Position” on page 24.) Close the tractor’s three-point hitch locking levers (if equipped).

  • Page 29: Pto Installation

    Operation PTO Installation Install the PTO shaft from the blower to the tractor. The angle of the PTO should not exceed 20 NOTE: [Figure 3] shows the relation between degrees. Angles greater than 20 degrees the height (H) of the tractor’s PTO and the result in excessive wear and reduce service angle of the PTO shaft.
  • Page 30 Operation Figure 3 PTO SHAFT ANGLE - REVERSING 2.25” 20° 15.75” 15° 2” 10° 5° 2” 20.5” 23.5” 11.75” 11.75” 19.5” 14.25” PTO SHAFT ANGLE - FRONT MOUNTING 2.25” 20° 15° 15.75” 2” 5° 10° 2” 7” 23.5” 11.75” 11.75” 23.5”...

  • Page 31: Alphablower Adjustment

    Operation AlphaBlower Adjustment The snow blower must be adjusted so that it is level. INCORRECT INCORRECT CORRECT For the blower to penetrate all the way down to 1. Locate a level surface to adjust the blower. the asphalt it is very important that the blower is 2.
  • Page 32 Operation AlphaBlower Adjustment (Cont’d) 6. Adjust wear shoes / gauge wheels so that these are flush with the surface.Then tighten the adjustment screw slightly more so that the wear shoes / gauge wheels are pushed down against the surface. 7. Adjust the top link outward slightly. The blower will now lift a little at the front.

  • Page 33: Hydraulic Couplers

    Operation Hydraulic Couplers Checking AlphaBlower Operation NOTE: After installing the snow blower, test all functions before operating the snow blower in the work area. • Thoroughly clean the quick couplers before making connections. Dirt can quickly damage the hydraulic system. AVOID INJURY OR DEATH •...
  • Page 34 Operation Checking AlphaBlower Operation (Cont’d) Engage the machine’s auxiliary hydraulics. (See the machine’s operation manual for correct procedure.) Auger Rotation Start auger rotation. Raise the engine RPM. Allow the snow blower auger to rotate for a short time (approximately one minute). Stop auger rotation.

  • Page 35: Operating The Alphablower

    Operation Operating The Enter the machine. (See “Entering The Operator’s Position” on page 24.) AlphaBlower Start the engine and release the parking brake. Raise the snow blower slightly off the ground. Operation Move to the work area. Engage the machine’s auxiliary hydraulics. (See the machine’s Operation Manual for correct procedure.) AVOID INJURY OR DEATH...

  • Page 36: Clearing A Plugged Alphablower

    Operation Clearing a Plugged AlphaBlower AVOID SERIOUS INJURY OR DEATH If the auger / chute becomes clogged with snow, turn the machine’s engine off. Use a clearing rod, never insert hands or feet into the chute or auger opening. NOTE: If the AlphaBlower is equipped with the hydraulic tip down option the chute can be tilted down to remove snow from the impeller housing.

  • Page 37: Alphablower Removal

    Operation AlphaBlower Removal NOTE: When the connection frame has been AVOID BURNS installed for towing, the support jack must always be installed before the Hydraulic fluid, tubes, fittings and quick snow blower is disconnected from the couplers can get hot during operation. Be machine.
  • Page 38 AlphaBlower Operation and Maintenance Manual...

  • Page 39: Maintenance

    Maintenance Maintenance Safety ............. .39 General Maintenance .
  • Page 40 AlphaBlower Operation and Maintenance Manual...

  • Page 41: Maintenance Safety

    PTO shaft from the tractor specifications. SnowWolf will before performing maintenance on the snow responsible for injuries or damage caused by blower.

  • Page 42: General Maintenance

    Maintenance General Maintenance NOTE: After initial use, or repair/replacement of damaged parts, it is important to check the repaired or replaced parts for proper bolt AVOID SERIOUS INJURY OR DEATH torque, operation and leaks. Before operating or servicing system: Read and understand the machine’s owners manual.

  • Page 43: Alphablower Maintenance

    Maintenance AlphaBlower Maintenance AVOID SERIOUS INJURY OR DEATH Always turn off and lockout power on the machine before servicing the snow blower. AVOID SERIOUS INJURY OR DEATH Always disconnect hydraulic connections between the snow blower and the machine before performing any type of maintenance to the snow blower.

  • Page 44: Maintenance Schedule

    Maintenance Maintenance Schedule SERVICE PROCEDURES DESCRIPTION Daily Maintenance (or every 10 hrs) Check Grease Oil Lube Change Claw Coupling Wear Shoe Gauge Wheel Weekly Maintenance (or every 50 hrs) PTO Shaft Axle Ball Bearings Chute Fixing Screws Check Hydraulic Hoses Snow Blower Frame Hardware Monthly Maintenance (or every 170 hrs)

  • Page 45: Lubrication

    Maintenance Lubrication Gearbox Oil Change Figure 2 PTO Shaft Figure 1 NOTE: Make sure the snowblower is level. Grease the PTO shaft fittings (Item 1), bearing for the guard (Item 2) and telescoping tubes (Item 3) Remove the drain plug located on the bottom of [Figure 1] every 40 hours of operation.
  • Page 46 Maintenance Lubrication (Cont’d) Slew Ring Figure 5 Ball Bearings Figure 3 The slew ring (Item 1) [Figure 5] is equipped with four grease zerks. Use grease of the type Mobil Mobilith SHC 220 or equivalent. Rotate the chute The snow blower is equipped with three ball around and grease repeatedly to distribute the bearings (Item 1) [Figure 3] for the axle grease around the entire slew ring.

  • Page 47: Auger Axle Couplings

    Maintenance Auger Axle Couplings Hydraulic Hoses Check the couplings between the gearbox and the Check that there is no damage to hydraulic hoses. auger axle for wear. If there is significant wear, the Replace any damaged hoses. Also check for any bushings in the coupling must be replaced.

  • Page 48: Front Mount Gearbox (33-100-P)

    Maintenance Front Mount Gearbox (33-100-P) Figure 6 PTO Spline Bracket on Snow Blower on Snow Blower 1. Install the grub screws (Item 1) and the O-ring (Item 2) on the locking sleeve (Item 3) [Figure 6]. Check that the locking sleeve and the grub screws fit the holes on the splines pin.

  • Page 49: Cutting Edge Replacement

    Cutting Edge Replacement NOTE: Replace or flip the bolt-on cutting edge when it wears within 1/2” - 3/4”. Replace only with genuine SnowWolf cutting edge and hardware. 1. Park the machine on a level surface with the snow blower properly attached.

  • Page 50: Alphablower Disassembly

    Maintenance AlphaBlower Figure 8 Disassembly AVOID SERIOUS INJURY OR DEATH Securely block up the snow blower before working underneath. 1. Provide support beneath the augers and using wooden blocks. Figure 7 6. Support the gearbox (Item 3) [Figure 8] using a jack or similar.

  • Page 51: Alphablower Assembly

    Maintenance AlphaBlower Assembly Auger Axle Installation 1. Apply grease to all spline pins before When the augers are turned by 1/2 a turn there installation to prevent the pins from corroding. should be no more than 0.04” variation measured between the flanges. If the variation is greater 2.

  • Page 52: Troubleshooting

    Maintenance Troubleshooting 33-100-P PROBLEM CAUSE SOLUTION Snow Blower not adjusted Adjust the snow blower. properly. Snow blower leaving snow behind. Replace cutting edge / wing Cutting edge worn or damaged. cutting edges. Gearbox faulty. Repair or replace. Bolt in PTO shaft sheared. Replace bolt.

  • Page 53: Wireless Controls 33-100-H

    Maintenance Troubleshooting (Cont’d) Wireless Controls 33-100-H PROBLEM CAUSE SOLUTION Blown fuse. Replace 20 amp fuse. Receiver not operating. Bad wire connection. Check wire connections. Replace receiver. See Wireless Receiver not working properly. Receiver faulty. Controls 33-100-H on page 20. Charge battery. Replace transmitter.

  • Page 54: Storage And Return To Service

    Maintenance Storage And Return To Service Storage Return to Service After the seasons use or when the snow blower After the snow blower has been in storage, it is will not be in use for a period of time, perform the necessary to follow a list of items to return the following steps.

  • Page 55: Parts

    Parts AlphaBlower (Both Models) ............56 AlpaBlower Parts .
  • Page 56 AlphaBlower Operation and Maintenance Manual...
  • Page 57 Parts This page left intentionally blank AlphaBlower Operation and Maintenance Manual...

  • Page 58: Alphablower (Both Models)

    Parts AlphaBlower (Both Models) AlpaBlower Parts AlphaBlower Operation and Maintenance Manual...
  • Page 59 Parts ITEM PART # DESCRIPTION 0990-C Chute, 4-Stage with Guard and Deflector 2013-010C Snow Blower, 540 rpm 2013-010CX Snow Blower, 1000 rpm 2014-400TP Connection Frame, 3-Point 0990-300 Cylinder, Hydraulic Tilt 0994 Chute, Telescopic (Optional) 2006-550 Swivel Stopper 2011-560H Drift Cutter, Right 2011-560V Drift Cutter, Left 10, 11...
  • Page 60 Parts AlphaBlower (Both Models) (Cont’d) AlphaBlower Parts (Cont’d) Detail A Detail A AlphaBlower Operation and Maintenance Manual...
  • Page 61 Parts ITEM PART # DESCRIPTION F102-12035 Bolt, Hex F102-12030 Bolt, Hex F312-12 Nut, Lock 2013-999B 0278-097 Clearing Rod 2013-350CV Auger, Left 2013-501 Cutting Edge, Level, 12 x 200 x 1256 F313-16N Nut, Lock F102-16055 Bolt, Hex F113-16050 Bolt, Locking F420-12 Washer, Seating 2013-520 Replaceable Edge, Blower Housing...
  • Page 62 Parts AlphaBlower (Both Models) (Cont’d) AlphaBlower Parts (Cont’d) Detail C Detail B AlphaBlower Operation and Maintenance Manual...
  • Page 63 Parts 33-100-P ITEM PART # DESCRIPTION 0984-510 Motor, Hyd Swivel F312-12 Nut, Lock F402-13 Washer, Seating F102-12045 Bolt, Hex 2007-835 Handle 2007-838 Sleeve F312-16 Nut, Lock F102-16065 Bolt, Hex F102-12065 Bolt, Hex F460-04 Spring Pin F302-16 Nut, Hex 2010-380 Guard, PTO Stub Shaft 2010-385 Guard, Fixtures F430-60...
  • Page 64 Parts AlphaBlower (Both Models) (Cont’d) AlphaBlower Parts (Cont’d) 33-100-P ITEM PART # DESCRIPTION 2013-350CH Auger, right F102-08035 Bolt, Hex F102-16045 Bolt, Hex F410-08 Washer, Seating 2014-256 Washer, Lock F312-08 Nut, Lock F423-16 Washer, Friction 2013-391 Guard L30-027 Gear Box 540 RPM L30-028 Gear Box 1000 RPM 2012-253...

  • Page 65: Auger Axle

    Parts AlphaBlower (Both Models) (Cont’d) Auger Axle ITEM PART # DESCRIPTION 2013-351H Screw, Right 2013-351V Screw, Left 2013-355CH Auger Axle, Right 2013-355CV Auger Axle, Left 2013-355CV Auger Wing, Right 2013-370V Auger Wing, Left F102-12035 Bolt, Hex F102-16040 Bolt, Hex F102-16050 Bolt, Hex F312-12 Nut, Lock...
  • Page 66 Parts AlphaBlower (Both Models) (Cont’d) Auger Axle (Cont’d) Detail A ITEM PART # DESCRIPTION 2013-360BH Auger Axle, Right 2013-360VH Auger Axle, Left 2013-375C Plate, Flange 2013-390H Clutch, Cut Out, Right 2013-390V Clutch, Cut Out, Left F102-16070 Bolt, Hex F305-20L Nut, Hex F312-16 Nut, Lock K03-22...
  • Page 67 Parts This page left intentionally blank AlphaBlower Operation and Maintenance Manual...

  • Page 68: Hydraulic Swivel Motor

    Parts AlphaBlower (Both Models) (Cont’d) Hydraulic Swivel Motor AlphaBlower Operation and Maintenance Manual...
  • Page 69 Parts ITEM PART # DESCRIPTION 0984-301C Cog Wheel 0984-310 Hose, Hydraulic (includes items 20, 21 & 22) 0984-603 Cover 0984-604 Sleeve, Spacer 0984-605 Engine Support Slew Ring F102-08025 Bolt, Hex F102-12100 Bolt, Hex F312-12 Nut, Lock F402-08 Washer, Seating F410-10 Washer, Seating G01-074 Nipple, 1/2”...

  • Page 70: Deluxe Chute, 4-Stage

    Parts AlphaBlower (Both Models) (Cont’d) Deluxe Chute, 4-Stage See Chute, Hydraulic Tilt on page Detail A AlphaBlower Operation and Maintenance Manual...
  • Page 71 Parts 33-106-P ITEM PART # DESCRIPTION 0991-016 Bolt, Hex 1900-040 Flap 4 1900-045 Flap 3 1900-050 Flap 2 1900-055 Flap 1 1900-073 1900-075 Chute 1900-079 Sleeve 1900-080 Tutfeste 1900-085 Sleeve 1900-086 Sleeve 1900-090 Guard 1900-140 Sleeve 1900-208 Hose, Hydraulic 1900-210 Hose, Hydraulic 1900-212 Hose, Hydraulic...

  • Page 72: Chute, Hydraulic Tilt

    Parts AlphaBlower (Both Models) (Cont’d) Chute, Hydraulic Tilt 33-106-P ITEM PART # DESCRIPTION 1900-200 Hose, Hydraulic 1900-205 Hose, Hydraulic 1900-206 Hose, Hydraulic F102-06080 Bolt, Hex F312-06 Nut, Locking F430-16 Retaining Ring F611-027 Clamp, Double G01-076 Nipple G01-080 Nipple G01-091 T-nipple G50-062 Gasket, Steel / Rubber H05-011...

  • Page 73: Chute, Swivel Stopper

    Parts AlphaBlower (Both Models) (Cont’d) Chute, Swivel Stopper ITEM PART # DESCRIPTION 0984-551 Bracket 0984-552 Bracket F102-10035 Bolt, Hex F169-12030 Bolt, Cylinder F302-06 Nut, Hex F312-10 Nut, Lock F402-10 Washer, Seating F420-12 Washer, Spring K08-023 Rubber Damper AlphaBlower Operation and Maintenance Manual...

  • Page 74: Three-Point, Connection Frame

    Parts AlphaBlower (Both Models) (Cont’d) Three-Point, Connection Frame AlphaBlower Operation and Maintenance Manual...
  • Page 75 Parts ITEM PART # DESCRIPTION 0859 Bolt, Top Link Cat. 2 1290-095 Bolt, Support Jack 2011-098 Bracket 2012-440 Coupling Bolt 2014-400C Connection Frame, 3-Point, Welded 2014-420 Support, Jack 2110-020 Bolt F102-08080 Bolt, Hex F102-10055 Bolt, Hex F312-08 Nut, Lock F312-10 Nut, Lock F470-05 Ring Pin...

  • Page 76: Alphablower (Model 33-100-H)

    Parts AlphaBlower (Model 33-100-H) Hydraulic Manifold AlphaBlower Operation and Maintenance Manual...
  • Page 77 Parts ITEM PART # DESCRIPTION P30188 Manifold Assembly With Fittings (includes items 1-15) P38232 Cartridge, Check Valve P38229 Cartridge, Relief Valve Differential 100-1500 PSI Plug, SAE-8 Hex Head P38228 Spool Valve, (Torque to 70 FT. LBS) P38231 Coil, P Series, 12 VDC, Deutsch P38230 Cartridge, Solenoid, 4W3P Tandem Center Plug, SAE-6, Hex Head...

  • Page 78: Hydraulic Pump

    Parts AlphaBlower (Model 33-100-H) (Cont’d) Hydraulic Pump ITEM PART # DESCRIPTION P38225 Hydraulic Pump Assembly AlphaBlower Operation and Maintenance Manual...

  • Page 79: Wireless Controls

    Parts Wireless Controls ITEM PART # DESCRIPTION Magnetic Charger Pad Transmitter, 8 Button Receiver AlphaBlower Operation and Maintenance Manual...

  • Page 80: Decal Identification (Both Models)

    DECAL, CAUTION HYDRAULICS DC124 DECAL, READ MANUAL DC126 DECAL, STAY CLEAR DC123 DECAL, CRUSH HAZARD DC127 DECAL, 3 in 1 WARNING DC28 DECAL, SNOWWOLF DC29 DECAL, WOLHEAD SWSN DECAL, SERIAL # DC115 33-100-H DC116 33-100-P AlphaBlower Operation and Maintenance Manual...
  • Page 81 Parts This page left intentionally blank AlphaBlower Operation and Maintenance Manual...

  • Page 82: Options (Both Models)

    Parts Options (Both Models) Chute, Telescopic Detail E Detail A Detail C Detail B Detail D AlphaBlower Operation and Maintenance Manual...
  • Page 83 Parts ITEM PART # DESCRIPTION 0994-003 Bolt 0994-020 Loading Section, Lower 0994-040 Bracket, Sliding 0994-050 Hatch 0994-060 Arm, Locking 0994-100 Loading Section, Upper 0994-150 Deflector, Adjustable 0994-160 Bracket 0994-210 Hose, Hydraulic 0994-220 Hose, Hydraulic 0994-230 Hose, Hydraulic 1535-560 Hose, Hydraulic 1554-988 Hose, Hydraulic 2060-951...

  • Page 84: Side Panels

    Parts Options Model (Both Models) (Cont’d) Side Panels ITEM PART # DESCRIPTION 2011-270H Plate, Replaceable, Right 2011-270V Plate, Replaceable, Left 2013-260H Plate, Right Side 2013-260V Plate, Left Side F102-16040 Bolt, Hex F102-16045 Bolt, Hex F102-16055 Bolt, Hex F312-16 Nut, Lock AlphaBlower Operation and Maintenance Manual...

  • Page 85: Drift Cutter

    Parts Options (Both Models) (Cont’d) Drift Cutter ITEM PART # DESCRIPTION 2011-561V Drift Cutter, Top, Plate, Left 2011-561H Drift Cutter, Top, Plate, Right 2011-564 Bracket 2011-565V Supporting Rod, Left 2011-565H Supporting Rod, Right F102-12055 Bolt, Hex F102-16040 Bolt, Hex F312-12 Nut, Lock F312-16 Nut, Lock...

  • Page 86: Gauge Wheels (Foam Filled)

    Parts Options (Both Models) (Cont’d) Gauge Wheels (Foam Filled) AlphaBlower Operation and Maintenance Manual...
  • Page 87 Parts ITEM PART # DESCRIPTION Gauge Wheels. Set with 2 Wheels - 1 x 2012-550H 2012-550 - 1 x 2012-550V 2012-550V Gauge Wheel, Left 2012-560V Wheel Bracket, Left K07-034 Axle no. 21 K07-039 Wheel 6.00 x 9” PR10, Truck Wheel 2012-550H Gauge Wheel, Right, (includes items 2, 3, 6, 7 &...

  • Page 88: Options (Model 33-100-P)

    Parts Options (Model 33-100-P) Gearbox, Front Mounting AlphaBlower Operation and Maintenance Manual...
  • Page 89 Parts ITEM PART # DESCRIPTION 2012-612 Locking Sleeve 2012-613 Washer, Lock 2012-614 Locking Flange 2012-615 Axle Guard Fixture 2012-617 Drilling Template 2012-620 Safety Bolt 2014-164 Bracket 2014-840 Bracket, Gear Box 2014-845 Plate, Support F102-12020 Bolt, Hex F102-12130 Bolt, Hex F102-16040 Bolt, Hex F102-16050 Bolt, Hex...

  • Page 90: Wing Kit

    Options (Cont’d) Wing Kit Detail A AlphaBlower Operation and Maintenance Manual...
  • Page 91 Parts ITEM PART # DESCRIPTION 0859 Bolt Cat.II 0995-464M Hydraulic Hose 3/8” x 4000 R/V 1252-289 Hydraulic Hose 1/2” x 750 R/V 1292-AC Hydraulic Cylinder 2013-701 Shims 2013-710 Bracket 2013-720 Cutting Edge 2013-730 Cylinder Bracket 2013-735 Bolt 2013-745 Sleeve 2013-750 Bolt 2013-760 Cutting Edge...
  • Page 92 AlphaBlower Operation and Maintenance Manual...

  • Page 93: Specifications

    Specifications AlphaBlower Specifications ............93 Torque Specifications .
  • Page 94 AlphaBlower Operation and Maintenance Manual...

  • Page 95: Alphablower Specifications

    Specifications AlphaBlower Specifications DESCRIPTION 33-100-H 33-100-P Overall Width at Drift Breakers (cm) 106.5" (270) 106.5" (270) Center Cutting Height (cm) 44.0" (112) 44.0" (112) Side Cutting Height (cm) 76.4" (194) 76.4" (194) Impeller Diameter (cm) 32.7" (83) 32.7" (83) Impeller Depth (cm) 11"...

  • Page 96: Torque Specifications

    Specifications Torque Specifications Standard Hardware And Lock Nuts BOLT SAE GRADE 5 SAE GRADE 8 LOCK NUTS TYPE Nominal Plated or Plated W / Plated or Plated W / Plated or Plated W / Size Unplated ZnCr Unplated ZnCr Unplated ZnCr W / Grade W / Grade...
  • Page 98 14311 Ewing Avenue, Burnsville, MN 55306 1-800-905-2265 snowwolfplows.com © 2021 SnowWolf...

This manual is also suitable for:

Alphablower 33-100-h

Table of Contents