Table of Contents
Related Manuals for HBX HydroBloc 0110
Summary of Contents for HBX HydroBloc 0110
- Page 1 Version 1.2.0 HYD-0110 HBX Control Systems Inc. H y d r o B l o c M a n u a l P a g e 1 © H B X C o n t r o l S y s t e m s I n c .
-
Page 2: Table Of Contents
Control Systems Inc. H B X H Y D - 0 1 1 0 H y d r o B l o c H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . -
Page 3: Section 1 - Introduction & Installation
– Return Connection installation. – Supply Fitting The HBX HYD-0110 is a microprocessor • 4 3/4” Unions based controller and as such is not to • 1 Interconnect Wire be regarded as a safety (limit) control. -
Page 4: General Technical Data
GENERAL TECHNICAL DATA Nameplate Information: The exterior label contains specific information unique Input Voltage: to your HBX HydroBloc and identifies some of the 120 VAC, ± 10%, 60Hz, 2A basic features. The label displays the serial number 2 x Thermistor Inputs:... -
Page 5: Main Parts And Labels
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 2. Navigation Buttons 1. Digital Display 13. Terminal Block 3. -
Page 6: Pump Curve
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 HYDROBLOC PERFORMANCE PUMP CURVE Pump Curve for UPS15-78 Speed 1 Speed 2 Speed 3... -
Page 7: Fitting Installation
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 INSTALLATION FITTING ASSEMBLY To place each fitting into the port on the Hydrobloc first place the o-ring over the fitting. -
Page 8: Terminal Designations
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 WIRING AND INSTALLATION Terminal 1 and 2: Thermostat Input Run wire straight from thermostat. -
Page 9: Section 2 - Programming The Control
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 SCREEN COLOURS Light Blue No Heat Demand — Heat Demand and the boiler is running —... - Page 10 H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 DESIGN TEMPERATURES OUT DESIGN — This is the design outdoor temperature. It is used in outdoor reset design calculation.
- Page 11 H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 BOILER SETTINGS Type: Reset — When set to RESET the supply water temperature will change based on outdoor reset.
- Page 12 H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 DEFAULTS/PURGE C or F — This setting is used to set the temperatures displayed on the control in either Celsius or Fahrenheit.
-
Page 13: Section 3 - Application Drawings
H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 HYD-0110-01 DRAWING: Boiler/Chiller Description: Controller Indoor This drawing exhibits the HydroBloc in a multiple- Outdoor Thermostat Sensor... - Page 14 H B X H Y D - 0 1 1 0 H y d r o B l o c V e r s i o n 1 . 2 . 0 HYD-0110-03 DRAWING: Description: Outdoor Each unit of a multi-family dwelling (an apartment Sensor for example) can have independent outdoor reset control.
-
Page 15: Warranty Information
HBX shall not be liable under this warranty; if its testing and examination discloses that the alleged defect in the product does not exist or was caused by the purchasers or third persons misuse, neglect, improper installation or testing, unauthorized attempts to repair or any other cause beyond the range of intended use, or by accident, fire, lightning or other hazard. - Page 16 HBX Control Systems Inc. 4516 - 112 Avenue SE © HBX Control Systems Inc. 2020 Calgary, AB Canada T2C 2K2 H y d r o B l o c M a n u a l P a g e 1 5...
Need help?
Do you have a question about the HydroBloc 0110 and is the answer not in the manual?
Questions and answers