Advertisement
Quick Links
Advertisement
Related Manuals for Living Culture TASMAN
Summary of Contents for Living Culture TASMAN
- Page 1 TASMAN & NORFOLK ALUMINUM PERGOLA MANUAL 5X3 5X4 6X3 6X4...
- Page 2 <2/21> INSTALLATION NOTES Before you start to install product ,please read below notes: 1.This is a general version manual .Please make sure that you review original design when place an order and read this manual several times before start to assemble the pergola .These installation steps can be referred to in this manual ,However ,other specific details such as motor position ,drainage direction ect.
-
Page 3: Table Of Contents
<3/21> motor code name section photo code name section photo motor post connecting louvre post louvre led light post louvre control post gutter beam & cover gutter beam & gutter gutter cover gutter beam & cover gutter beam & gutter gutter cover... - Page 4 <4/21> HARDWARE code name photo base plate SUS hex screw (M8*16) M8 washer SUS hex expansion bolt（M10*100） L post end cover cross tapping screw (4.2*16) cross drilling screw 4.2*19) post corner extension piece louvre pivot cover 4*14 cross drilling screw φ8*M6*5 hex thumb screw motor connecting louvre cover（R）...
- Page 5 <5/21> TOOLS ∅ 14mm hammer electrical hand drill screwdriver drill bar drill marker 16mm wrench ladderX3 helmet rubber hammer electric spirit tape level INSTALLATION STEP 1: Assemble the posts with base plates Tip： A4 post is the power input site , and the docoration cover is different...
- Page 6 <6/21> STEP 2:Assemble the beam & gutter ( with pivot holder)with post Tip： 2.1 Insert the two gutter beams into the post use soft sponge to clean the surface treatment grooves and screw it 2.2 Fasten the screw from inside at the connection 2.3 Assemble the pergola frame on the floor and make it stand that needs one person to...
- Page 7 <7/21> STEP 3 :Adjust the pergola position and fix the posts on the floor 3.1、Adjust the 3.2、mark the position hole position 90° 90° 90° 90° 90° 90° 3.4 Stuff the expansion 3.3 Drill the 90° 90° plug into the hole holes Tip: 1.Ensure the post in correct position ,and...
-
Page 8: Gutter
<8/21> 4.4 Confirm each louvre position , then start to settle louvres as design A version showed 4.4-2 Settle the louvres ,keep the 4.4-1 Settle the louvres in the pivot holders led light louvre and motor connecting at both sides（fasten them when all louvres louvre at correct position settled with no fault）... - Page 9 <9/21> STEP 5:Connect to the power 5.3 Connect the cables 5.2 Insert the control system 5.1 You should connect the voltage into the post A1 please cable before insert the control system three plugs are led light cable two plugs are motor cable Tips：...
- Page 10 <10/21> 6.2-3 Check the remote function There are two procedures of remote , one is simple procedure without any zip screen ,the other is procedure 2 , you can remote the pergola and zip screen at one remote .The remote was pre-setted channel display procedure 1 .
- Page 11 <11/21> STEP 9 : Check the pergola function 9.1、the PCCB is essential during installation 9.2、check the motor function 9.3、check the remote function 9.3、check the louver movement and noise 9.4、check the led light function 9.5、check the other device function...
- Page 12 <12/21> HOW TO USE TUYA APP STEP1 :Open TUYA app 1. Prepare a common wifi for the pergola Tip: it needs 2.4GHz wifi 2. Open the phone bluetooth and TUYA app 5.Press and hole the button until the blue indicate light is blinking 6.
- Page 13 <13/21> How to authorize account to family members 一、 TUYA APP When you connect to tuya app successfully ,you can share the account to your family members share Tips： 1the owner's phone (A) connect to pergola ，he can operate the pergola by his phone A， 2.the other family members also download TUYA app and singn in 1.
- Page 14 <14/21> WALL-MOUNTED INSTALLATION INSTRUCTION Hardware list expansion plug(M14*75) wood screw (M10*100) 30 mm cap SUS hex screw (M8*12) 17mm wrench...
- Page 15 <15/21> STEP 1:Firstly install the wall-mounted beam & gutter 2.2 Mark the holes position through the 2.1 Take use of electric spirit level pre-drill holes on the gutter to mark the beam & gutter position 2.6 Stuff the 2.3 Drill 14 mm holes 2.4 Stuff the expansion 2.5 Use wrench...
- Page 16 <16/21> STEP 2 : Assemble the pergola frame 2.2-2 Loosen these two screws 2.1 Assemble the frame on the floor and make it stand 2.2-3 Insert the beam & gutter into the junction 2.2-4 Fasten the screw 2.2-5 Fasten the up and bottom screw 2.2-1 Insert the gutter into the post groove...
- Page 17 <17/21> The remain installation are as same as the previous steps Tips： 1.When you settle the louvres ,you should fasten the louvre pivot covers by each 3 pcs of louvres settled screw the louvre pivot covers 2.When the louvre vertical to wall ,you should install the again wall side control rod first.
- Page 18 <18/21> Ceiling Fan beam manual Hardware M8 screw nut fan beam plate M8X30 hex screw M6x70 hex screw M8 hex cap （2washers 2 +gasket+1 nut） fan beam Installation 1.1 Pull the ceiling fan beam 1.3 Fix one side as picture cable into the beam &...
-
Page 19: Led Light
<19/21> Trouble shooting malfunction solutions 1.check the cables connect if correct 2.check if there is an avaliable voltage for pergola : motor and led lights 110V or 220V don't work 3.check the remote if learn to match the control system 4.check the remote battery is work or not 5.check the control system has power output or not 1.check the motor is working or not... - Page 20 <20/21> Care and Maintenance CARING FOR YOUR PERGOLA Structure surface coated with the thermosetting powder coating must be cleaned once a year to maintain their original appearance Thermosetting powders are sensitive to : 1.Physical friction ,hard impact ,extrusion ,chemicals including alkaline solvent and acidic solvent.
- Page 21 Please feel free to leave reviews on our website or call us directly . Thanks again and we are pleasure to serve you , if there is anything is not clear to you ,please contact us . Gratefully LIVING CULTURE...