Related Manuals for Living Culture Villa
Summary of Contents for Living Culture Villa
- Page 1 User Instructions Villa Pergola for motorised operation Size:600x400 cm (double bay)
-
Page 2: Table Of Contents
Keep this manual for future reference. Dear Customer, Congratulations and thank you for choosing to buy the Villa Pergola from our company. To enjoy this product for a long time and for your own and the safety of other people, please follow the assembly instructions. -
Page 3: Parts List
Parts List Please check all parts against the parts list before commencing construction of pergola. SIZE：600X400CM (double bay) PARTS LIST... - Page 5 Hardware and other parts: ①M8x20 countersunk screw ②Screw for motor fixing ③Base plate ④Upright cover ⑤M10 screw cap ⑥M8x20 Hexagon bolt ⑦Plastic Spacer ⑧Locking nut ⑨Motor 1 with motor bracket ⑩Motor 2 with motor bracket ⑪M8X100 expansion bolt Gutter connector ○...
-
Page 6: Product Description
Product Description Make the most of your outdoor living area with your pergola. Relax and enjoy the outdoors while being protected from sun. The coated aluminum frame pergola is perfect for shading your garden, deck, courtyard and swimming pool. Important Safety Instructions Warning: For the safety of you and other persons it is important to follow below instructions and obey warnings. - Page 7 Do not install the pergola when you find damage parts are that parts are missing. Contact your dealer. Keep children and pets out of the working area during assembly and adjustments. This product and its fixing parts are only suitable for installation on a plain cement wall or stable brickwork.
-
Page 8: Mounting
Mounting and usage Step 1 Attach base plate ③ x6 to the bottom of posts (C-1 X1,C-2 X1,C-3 X1,C-4X1,C-5 X2),use bolts x12 to attach with hex key or electric drill. ① C-1&C-3 ,C-2&C-4, C-5&C-5 posts should be installed diagonally as below. Please make sure all posts on the same horizontal plane. - Page 9 Step 2 Attach beam A-1X2 ,beam A-4 x2 ,beam A-2x1,beam A-3 x1 ,beam A-5 x1,use bolts ⑥x32 to fasten.
- Page 10 Step3 Use bolts ⑥x4 to fasten beam 1 & beam 4.
- Page 11 Step4 Attach upright cover ④x4,use bolts ⑥x8 to fasten...
- Page 12 Step 5 Attach all eight gutters B-1X4,B-2X2,B-3X2 by hooking inside the A-1,A-2,A-3 beams. Remark: Please put some silicon on the connection between the gutters & middle beams&middle posts after installation.
- Page 13 Step 6 Located holes in centre of beams(A-2,A-3,A-5) D-2intohole which on slot beam A-2,A-3,A-5, lining up with the Place centre louver holes for 600*400 cm size. Using M10 nut ⑤X2, secure the louver in place Place Driving louver D-3in line with 7th slot (check attached direction） on the beam A-2,A-3,A-5, Fit all common louvers D1 into the remaining slots in the beams...
- Page 14 Step 7 ○ Fasten motor ⑨x1+ 10 X1as shown below.
- Page 15 Step 8 ○ ○ Fasten 12 x4 gutter connector and 13 x2 (50 to 40 connector). Connect the female and male plugs for the LED lighting (DC24V to DC24V) and motor (DC24V to DC24V) and plug the power cable into local socket.
- Page 16 Step 9 ○ E x 4 (flat L-shaped aluminum profile). One for each other of the slats is required. Use bolt⑥x128, plastic spacer⑦x128 and nut⑧x128 to tighten for 600X400cm size. Secure the louvers at each end. NOTE: Do not over tighten. Over tightening will prevent louvers from moving.
- Page 17 Step 10 ○ Mark holes for expansion bolt 11 x4 on each post. Note the drill size should be 12 mm. Insert the bolts. Use an hammer drill if necessary. Place the posts over the bolts. Tighten the nuts. Once installed, make sure any remaining plastic is removed and silicone is used along all corners and gutters to waterproof.
- Page 18 Motor setup...
-
Page 19: Dismounting
Dismounting If you want to disassemble the Pergola, please follow the following process. Attention! At least two people are needed for this step. Keep the Pergola louvers open before you begin with dismounting. Bind the Louvers of the Pergola together to ...