Matco Tools MAXIMUS PRO HD Quick Start Manual

MDMAXPROHD Scan Tool
The scan tool acts as the central processing system, which is used to receive and analyze the
live vehicle data from the VCI dongle and then output the test result.
Data Transmission Port
(Reserved for add-on
modules, and
other USB devices use only.)
Memory Card Slot
(To store the memory card
for storage extension.)
Charging Indicator
(Red means Charging, and
Green means Fully Charged.)
Microphone
10.1" Touch Screen
Rear Camera
Audio Speaker
Foldable Stand
(Flip out it to any angle and work comfortable
at your desk, or hang it on steering wheel.)
VCI (Vehicle Communication Interface)
The MAXSYNC VCI dongle works as a heavy duty / medium duty / light duty vehicle
communication interface device, which is used to connect to the vehicle's DLC (Data Link
Connector) port via the diagnostic cable to read the test data and then send it to the scan tool.
DB-15 Diagnostic Connector
(To connect the diagnostic cable.)
3.97 Inch Touch Screen
LAN/WAN Port
(Reserved for other purposes. )
*Note: When the VCI dongle is connected to the scan tool via data cable, the system will
switch to USB mode automatically and the wireless communication will be disabled.
Type-C Charging Port
(Reserved for charging or transferring data.)
Power/Screen
Lock Button
Volume Buttons
Ambient Light Sensor
Microphone
Front Camera
Camera Flash
Audio Speaker
*Warning: The VCI dongle
obtains power through the
vehicle's DLC (Data Link
Connector) via the diagnostic
cable. Do NOT connect the
DC-IN port to an external DC
power supply if the VCI
dongle can be powered up
normally.
If the pin of the DLC is
damaged or the DLC has
insufficient power, connect
the DC-IN port to an external
DC power supply.
No responsibility can be
assumed for any damage or
loss caused as a result of not
strictly following the above
method.
DC-IN Port
(See "*Warning".)
Data I/O Port
(To connect it to the scan tool to
perform diagnosis via the data cable.)
Quick Start Guide
Included Accessory Checklist
Vehicle Communication
MDMAXPROHD Scan
Tool Interface (VCI) Dongle
A tablet for showing test A device for accessing
vehicle data.
results.
Diagnostic Cable
Password Envelope
Connect the VCI dongle to
the vehicle's OBD II DLC
A piece of paper bearing
port. It can be separated Product S/N and
into two parts: DB15F to Verification Code, which is
HD15F data cable and required for your VCI
activation.
HD15M to OBD II adapter.
Cigarette Lighter Cable
Battery Clamps Cable
Supply power to the VCI
through connection to Supply power to the VCI
cigarette lighter through connection to
receptacle. vehicle battery.
Quick Start Guide
Working Principle
The following illustration demonstrates how the MAXIMUS PROHD diagnostic system
works.
MAXIMUS PROHD Scan Tool
Internet
Wi-Fi
*Note: If the VCI dongle is successfully activated, the scan tool
will automatically obtain the VCI ID and connect to it. In this case
it is not necessary for the user to manually configure it again. For
details on how to activate the VCI dongle, refer to Section 4.
Register & Update.
To Vehicle's DLC Port
Commercial Vehicle
1. Charging & Turning On
1. Connect one end of the included power adapter to Type-C charging port of the scan tool,
then connect the other end to the AC outlet.
*Warning: Please use the included power adapter to charge your tool. No responsibility
can be assumed for any damage or loss caused as a result of using power adapters other
than the one supplied.
2. After charging is complete, disconnect the power adapter from the AC outlet. Press
the

[POWER]
button on the
scan tool , the system starts initializing and then enters the home
screen.
MDMAXPROHD
Power Adapter
To supply power to the
scan tool through
connection to AC outlet.
Data Cable
Connect the VCI and scan
tool to perform vehicle
diagnosis.
Adapter Cables
Connect the diagnostic
cable and vehicle's non-
OBD II diagnostic socket.
2311226-16
MDMAXPROHD
VCI Dongle
or
Diagnostic Cable
2311226-16