Related Manuals for Lotus Prio Series
Summary of Contents for Lotus Prio Series
- Page 1 Mounting and User Instructions Lotus-Prio Series Stoves (Lotus Prio 1, Prio 2, Prio 3, and Prio 4, Prio 5, Prio 6) Version 1, 10/4-2005...
- Page 3 Introduction Congratulations on your new Lotus Wood Stove We sincerely trust that your Lotus Wood Stove will bring many happy hours for you. However, to benefit fully from your investment, you should read these instructions thoroughly. They contain some specific advice on how to benefit fully from your stove –...
- Page 4 Distance to Combustible Material For combustible material, such as combustible walls, furniture, etc., for reasons of safety a number of minimum distances apply. The following minimum distances apply: 150 mm behind 350 mm To the side 900 mm forward Distance to non-combustible material To non-combustible material, there should be a distance of 80-100 mm in order that the stove may release and distribute the heat while you may clean on and around the stove.
-
Page 5: Technical Specifications
C (1 : 2) Then hook the stove up on the fitting. The stove has two holes fitting the two top holes of the fitting. Fix the stove on the fitting. Stove hanging in this notch Mount shadow strip in this hole before stove is suspended Technical Specifications Model... - Page 6 Mean Values at testing to DS/EN 13240: Flue Gas Temperature: 293 C Flue Gas Mass Flow: 5.7 g/s Rate of Efficiency: Rated Output: 6.3 Kw Flue: 12 pa Chimney A good draught in your chimney is paramount to how well a stove will burn. Note that there should be access to cleaning doors.
- Page 7 Stålrøgvendeplade Steel smoke baffle plate Skamolrøgvendeplade Skamol smoke baffle plate Mounting of Smoke Baffle Plates Below, it has been shown how the smoke baffle plates are to be placed when viewing a section in the stove from the side. Each smoke baffle plate is removed separately. Both smoke baffle plates are removed by lifting up at one side after which they may come clear at the other side and be taken down into the combustion chamber and out of the door.
-
Page 8: Use Of Stove
Floor When placing your new Lotus stove on the floor, it should be put on a non- combustible plate, for instance of steel or stone material. The plate should be so large that it will reach a minimum of 30 cm in front of the stove, and 15 cm at each side of the fireplace opening. - Page 9 May only be used for kindling as well as stoking and may not be left open during the ordinary combustion). The register is damped as required during the kindling. When the fire has burned down to embers (no more flames), open the door gently so as not to whirl out the embers.
-
Page 10: Sound Advice
Cleaning of Stove All Lotus stoves have been factory treated with original Senotherm lacquer in ”coke” or ”grey” colour. Due to this treatment, the stove will, during the first kindlings, exude a special odour but that will vanish after a few times. Good airing to be provided. - Page 11 Wood for your Lotus stove should have a diameter of 7-9 cm and be max. appr. 30 cm long as it will otherwise come too close to the stove sides (at the DS testing 25 cm long wood has been used).
-
Page 12: Operating Trouble
Operating Trouble In case of any operating trouble with your Lotus stove, you may find the cause of that below. If not, please do not hesitate to contact your Lotus distributor. Stove hard to control – burning too quickly If your stove is new, check our guide. -
Page 13: Warranty
Lotus Heating Systems A/S. This warranty does not cover damage caused by inappropriate, non-expert/incompetent use of the stove. If a product is returned to Lotus Heating Systems A/S, and the damage subsequently turns out not to be covered by this warranty, any costs incurred shall be incumbent on the customer.